=head1 NAME smokeping_upgrade - Notes on upgrading Smokeping =head1 OVERVIEW This document tries to list incompatible or otherwise user-visible changes in Smokeping versions, with instructions on how to fix any possible problems. It also sporadically mentions new features and the like. The document currently starts with changes from 1.34 to 1.37. If you run into problems with upgrading from earlier versions, please send a description of the problems, preferably with notes on how to fix them, to the C mailing list, so they can be added to this document. The same applies to any problems you find with current versions that are not documented here, of course. Patch submissions against the POD source of this file are most appreciated. If a version is not listed, there are no known problems in upgrading to it from the previous release. An official list of changes with each release can be found in the CHANGES file in the Smokeping distribution. This document tries to complement that with upgrading instructions etc. =head1 1.38 to 2.0 The biggest change with the 2.0 release is that the configuration file is now parsed much more strictly. This should result in (hopefully understandable) error messages making the configuration less of the trial-and-error variety than it used to be. It also automates the generation of the configuration documentation from the source code, so the docs are now more accurate. The configuration syntax has stayed mostly the same, except for the issues below. =over =item PROBE_CONF The PROBE_CONF subsections have been deprecated. All the target-specific variables are now configured in the same section as the target is. Just deleting the ++ PROBE_CONF lines should fix this (for any number of '+', obviously.) The existence of a PROBE_CONF section makes smokeping exit with an error message at parse time. Note for distributors: these lines could easily be removed automatically during upgrade. =item Variable order The C variable must now be set before any variables that depend on the selected probe. This is because setting C modifies the grammar of the rest of the section dynamically at parse time. Additionally, C must now precede C, for reasons that have to do with the current implementation of mandatory variable checking. Both of these errors are recognized at parse time and produce error messages accordingly. Note for distributors: the C command now has a new '--check' option that can be used to verify the syntax of the configuration file. It might be a good idea to do this on upgrade and give the user an explanatory note if the verification fails. =item Target-specific variables in the Probes section This is not an incompatible change, but it is mentioned here nevertheless. Target-specific variables can now be specified in the Probes section as well, and the values given become defaults for all the targets. =item Timeouts The C variable in the Probes section is now the maximum time expected for B ping to take. Previously it was the maximum time allowed for all the pings to one target. This is an incompatible change, but the code now works in the way it was documented to work even in 1.38. Those probes offering a target-specific C variable will get a default for it from the Probes section, as noted in the previous item. This should ensure that probes that enforce the ping timeout themselves (most do) will not get killed due to timeout before they have a chance to do it. =item Matchers The matcher modules have been renamed to start with a capital letter, to differentiate the actual modules from the base classes. You have to capitalize the matcher name in the pattern definition accordingly. =item Minimum number of pings The C variable now has an enforced minimum value of 3, as the whole design of Smokeping is based on the idea of sending several probes and measuring and visualizing the variation between them. =item RRD parameter checking Smokeping now checks at startup that the parameters of any existing RRD files match those specified in the configuration file. If there is a discrepancy, it will give an error message and refuse to start. This situation is most likely to happen if you have modified the C or C variables in your configuration file. You'll then have to delete the old RRD file or somehow convert it to use the new parameters. The C command might be helpful here. =back In addition to this, some probes have had minor incompatible changes to their configuration. =over =item L The C variable is now mandatory. This is a side effect from a bigger change: the probe is now derived from the FPing probe and supports all the variables FPing does. =item L This probe is also now derived from FPing and supports all the variables FPing does. =item L The URL that will be used is now specified with the variable C instead of C. The new variable can (and usually should) include a placeholder for the C variable of each target as C<%host%>, eg. C. The new variable is mandatory. The change was made to fix the confusing situation where the C variable was required for each actual target, but it didn't actually have any effect (as the server to be probed came from the C variable.) Timeouts are now recognized properly by looking at the curl exit code. The default timeout of this probe has been raised to 10 seconds. The command line is now executed without an intervening /bin/sh, and so quotes are not needed anymore around the User-Agent string (the C parameter). Smokeping will complain if it notices quotes around the string. =item L The default timeout of this probe has been raised to 10 seconds. =item L The default timeout of this probe has been raised to 10 seconds. =item L The C variable is now mandatory, as the old default "/" didn't make sense because it's relative rather than absolute. =item L The C variable is now mandatory, as Net::LDAP bails out without it. The C variable was changed to C and its semantics were changed accordingly (it's now the minimum time between two queries rather than the time slept between the end of one and the start of the another.) =item L The C variable was changed to C and its semantics were changed accordingly. See the LDAP explanation above. =item L The C variable was changed to C and its semantics were changed accordingly. See the LDAP explanation above. Additionally, the time is now specified in seconds rather than microseconds. =item L The C variable was changed to C and its semantics were changed accordingly. See the LDAP explanation above. Additionally, the time is now specified in seconds rather than microseconds. =item L The name of this probe was changed: it now starts with a capital letter like all the others do. The C variable was removed. The target should now be specified in the C variable, like it is with all the other probes. =back =head1 1.34 to 1.37 =over =item The L probe The configuration of this probe was moved from the Targets section to the Probes section, as all the variables are really probe-specific. The moved variables were C, C and C. =item Logging changes The C daemon now warns at startup if syslog support is not turned on in the config file. This is because many diagnostic messages will otherwise get lost. =item Concurrent probes Each probe now runs in its own process, instead of them all running sequentially in one process. This makes it possible to specify different step lengths for different probes. You can get the old behaviour back by setting 'concurrentprobes = no'. =back =head1 COPYRIGHT Copyright 2005 by Niko Tyni. =head1 LICENSE This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. =head1 AUTHOR Niko Tyni =head1 SEE ALSO The other Smokeping documents, especially L.