1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
|
=head1 NAME
smokeping_master_slave - How run multiple distributed instances of SmokePing
=head1 OVERVIEW
Normally smokeping probes run their tests from the host where smokeping runs
to some target host and monitor the latency of the connection between the
two.
The Master/Slave concept enables all smokeping probes to run remotely. The
use case for this is to measure the overall connectivity in a network. If
you are interested in checking that your central DNS server or your file
server works for everyone, you could setup several smokeping instances
checking up on on the two servers from multiple locations within your
network. With the Master/Slave smokeping configuration this process becomes
much simpler, as one smokeping master server can control multiple slaves.
All monitoring data is stored and presented on the server, but collected by
the slaves. The slaves will also get their configuration information from
the master, so that you just have to maintain the master server
configuration file and the rest is taken care of automatically.
=head1 DESCRIPTION
=head2 Architecture
The slaves communicate with the master smokeping server via the normal
smokeping web interface. On initial startup each slave connects to the
master server and asks for its assignments. When the slave has done a round
of probing it connects to the master again to deliver the results.
If the assignment for a slave changes, the master will tell the slave after
the slave has delivered its results.
The master and the slaves sign their messages by supplying an md5 hash of the
message appended with a shared secret. Optionally the whole communication
can run over ssl.
[slave 1] [slave 2] [slave 3]
| | |
+-------+ | +--------+
| | |
v v v
+---------------+
| master |
+---------------+
The slave is a normal smokeping instance setup where the configuration comes
from the master instead of a local configuration file. The slave tries to
contact the master server after every round of probing, supplying its
results. If the master server can not be reached, the results will be sent
to the server together with the next round of results. Results will be
stored in a perl storable so that they survive a restart of the smokeping
instance.
=head2 Master Configuration
To configure a master/slave setup, add a slaves section to your smokeping
configuration file. Each slave has a section in the slaves part of the
master configuration file. The section name must match the hostname of the
slave. If some configuration parameter must be set to a special value for
the slave, use an override section to configure this.
The slave names must be the names the hosts think they have not their
outside hostnames or ip addresses or anything like that. When the slave
calls the master to get its config or report its measurements it will tell
the master its 'hostname'. This together with the shared secret is used to
authenticate and identify who is who.
*** slaves ****
secrets=/etc/smokeping/slavesecrets.conf
+slave1
display_name=erul22
location=India
++override
Probes.FPing.binary = /usr/bin/fping
...
Then in the targets section you can define slaves at every level. Again the
settings get inherited by lower order targets and can be overwritten
anywhere in the tree.
A slave will then get the appropriate configuration assigned by the server.
*** targets ***
slaves = slave1 slave2
...
+dest1
slaves =
...
+dest2
slaves = slave1
...
+dest3
...
The data from the slaves will be stored in F<TargetName~SlaveName.rrd>. So the example above would
create the following files:
dest1.rrd
dest2.rrd
dest2~slave1.rrd
dest3.rrd
dest3~slave1.rrd
dest3~slave2.rrd
=head2 Slave Configuration
A smokeping slave setup has no configuration file. It just needs to know
that it runs in slave-mode and its secret. The secret is stored in a file for
optimal protection. By default the persistent data cache will be located in
F</tmp/smokeping.$USER.cache>.
./smokeping --master-url=http://smokeping/smokeping.cgi \
--cache-dir=/var/smokeping/cache.file \
--shared-secret=/var/smokeping/secret.txt
=head1 COPYRIGHT
Copyright (c) 2007 by Tobias Oetiker, OETIKER+PARTNER AG. All right reserved.
=head1 LICENSE
This program is free software; you can redistribute it
and/or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation; either
version 2 of the License, or (at your option) any later
version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE. See the GNU General Public License for more
details.
You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free
Software Foundation, Inc., 675 Mass Ave, Cambridge, MA
02139, USA.
=head1 AUTHOR
Tobias Oetiker E<lt>tobi@oetiker.chE<gt>
=cut
|
