summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorjpetermans <tibcmhhm@gmail.com>2017-05-09 01:15:20 +0200
committerjpetermans <tibcmhhm@gmail.com>2017-05-09 01:15:20 +0200
commit821f72eae94ce4f1b93bab1376b2187698206b65 (patch)
tree22f3cd2eaa13978c8aad7b8423573fa5e052bdb1
parentb5675e20255a9306097ad58dabc8727a2c190946 (diff)
downloadqmk_firmware-821f72eae94ce4f1b93bab1376b2187698206b65.tar.gz
qmk_firmware-821f72eae94ce4f1b93bab1376b2187698206b65.tar.xz
documentation cleanup
-rw-r--r--keyboards/infinity60/keymaps/jpetermans/readme.md69
-rw-r--r--keyboards/infinity60/led_controller.c6
2 files changed, 41 insertions, 34 deletions
diff --git a/keyboards/infinity60/keymaps/jpetermans/readme.md b/keyboards/infinity60/keymaps/jpetermans/readme.md
index 9c5b89173..fcad4b140 100644
--- a/keyboards/infinity60/keymaps/jpetermans/readme.md
+++ b/keyboards/infinity60/keymaps/jpetermans/readme.md
@@ -3,10 +3,10 @@ Backlight for Infinity60
## Led Controller Specs
-The Infinity60 pcb uses the IS31FL3731C matrix LED driver from ISSI [datasheet](http://www.issi.com/WW/pdf/31FL3731C.pdf). The IS31 has the ability to control two led matrices (A & B), each matrix controlling 9 pins, each pin controlling 8 leds. The Infinity only utilizes matrix A.
+The Infinity60 (revision 1.1a) pcb uses the IS31FL3731C matrix LED driver from ISSI [(datasheet)](http://www.issi.com/WW/pdf/31FL3731C.pdf). The IS31 has the ability to control two led matrices (A & B), each matrix controlling 9 pins, each pin controlling 8 leds. The Infinity only utilizes matrix A.
-Infinity60 LED MAP:
-digits mean "row" and "col", i.e. 45 means C4-5 in the IS31 datasheet, matrix A
+Infinity60 LED Map:
+digits mean "row" and "col", i.e. 45 means pin 4, column 5 in the IS31 datasheet
```c
11 12 13 14 15 16 17 18 21 22 23 24 25 26 27*
28 31 32 33 34 35 36 37 38 41 42 43 44 45
@@ -17,19 +17,26 @@ digits mean "row" and "col", i.e. 45 means C4-5 in the IS31 datasheet, matrix A
*Unused in Alphabet Layout
The IS31 includes 8 pages (or frames) 0-7 and each page consists of 0xB4 (144) bytes
-- **0 - 17** LED control (on/off). 18 pins which alternate between A and B matrices (CA1, CB1, CA2, CB2, ..). Each byte controls the 8 leds on that pin with bits (8 to 1).
-- **18 - 35** Blink control. Same as LED control above, but sets blink on/off.
-- **36 - 143** PWM control. One byte per LED, sets PWM from 0 to 255. Same as above, the register alternates bytes between the A & B matrices.
+- **0 - 17**
+ * LED control (on/off).
+ * 18 pins which alternate between A and B matrices (CA1, CB1, CA2, CB2, ..).
+ * Each byte controls the 8 leds on that pin with bits (8 to 1).
+- **18 - 35**
+ * Blink control.
+ * Same as LED control above, but sets blink on/off.
+- **36 - 143**
+ * PWM control. One byte per LED, sets PWM from 0 to 255.
+ * Same as above, the register alternates, every 8 *bytes* (not bits) between the A & B matrices.
## Led Controller Code
-led_controller.c sets up ability to write led layers at startup or control leds on demand as part of fn_actions. By default led_controller.c assumes page 0 will be used for full on/off and page 7 for controlling individual leds. The remaining 6 pages (1-6) are free to preset led maps at init or on demand. Communication with the IS31 is primarily done through the led_mailbox using chMBPost described further below under "Sending messages in Keymap.c"
+In the Infinity60 project folder, led_controller.c sets up ability to write led layers at startup or control leds on demand as part of fn_actions. By default led_controller.c assumes page 0 will be used for full on/off and page 7 for controlling individual leds. The remaining 6 pages (1-6) are free to preset led maps at init or on demand. Communication with the IS31 is primarily done through the led_mailbox using chMBPost described further below under "Sending messages in Keymap.c"
-One function is available to directly control leds:
+One function is available to directly set leds without the mailbox:
```
write_led_page(page#, array of leds by address, # of leds in array)
```
This function saves a full page using a supplied array of led locations such as:
-```
+```c
uint8_t led_numpad[16] = {
18,21,22,23,
37,38,41,42,
@@ -39,24 +46,24 @@ uint8_t led_numpad[16] = {
write_led_page(5, led_numpad, 16);
```
-Remaining led control is done through the led mailbox using these message types.
-- **SET_FULL_ROW** - 3 bytes: row#, message type, 8-bit mask. Sets all leds on one pin per the bit mask.
-- **OFF_LED** - 2 bytes: message type, led address. Turn off specific led.
-- **ON_LED** - 2 bytes: message type, led address. Turn on specific led.
-- **TOGGLE_LED** - 2 bytes: message type, led address. Toggle specific led on/off.
-- **BLINK_OFF_LED** - 2 bytes: message type, led address. Set blink off for specific led.
-- **BLINK_ON_LED** - 2 bytes: message type, led address. Set blink on for specific led.
-- **BLINK_TOGGLE_LED** - 2 bytes: message type, led address. Toggle blink for specific led.
-- **TOGGLE_ALL** - 2 bytes: message type, not used. Turn on/off full backlight.
-- **TOGGLE_BACKLIGHT** - 2 bytes: message type, on/off. Sets backlight completely off, no leds will display.
-- **DISPLAY_PAGE** - 2 bytes: message type, page to display. Switch to specific pre-set page.
-- **RESET_PAGE** - 2 bytes: message type, page to reset. Reset/erase specific page.
-- **TOGGLE_NUM_LOCK** - 2 bytes: message type, on/off (NUM_LOCK_LED_ADDRESS). Toggle numlock on/off. Usually run with the `set_leds` function to check state of numlock or capslock. If all leds are on (e.i. TOGGLE_ALL) then this sets numlock to blink instead (this is still a little buggy if toggling on/off quickly).
-- **TOGGLE_CAPS_LOCK** - 2 bytes: message type, on/off (CAPS_LOCK_LED_ADDRESS). Same as numlock.
-- **STEP_BRIGHTNESS** - 2 bytes: message type, and step up (1) or step down (0). Increase or decrease led brightness.
+Remaining led control is done through the led mailbox using these message types:
+- **SET_FULL_ROW** (3 bytes) - row#, message type, 8-bit mask. Sets all leds on one pin per the bit mask.
+- **OFF_LED** (2 bytes) - message type, led address. Turn off specific led.
+- **ON_LED** (2 bytes) - message type, led address. Turn on specific led.
+- **TOGGLE_LED** (2 bytes) - message type, led address. Toggle specific led on/off.
+- **BLINK_OFF_LED** (2 bytes) - message type, led address. Set blink off for specific led.
+- **BLINK_ON_LED** (2 bytes) - message type, led address. Set blink on for specific led.
+- **BLINK_TOGGLE_LED** (2 bytes) - message type, led address. Toggle blink for specific led.
+- **TOGGLE_ALL** (2 bytes) - message type, not used. Turn on/off full backlight.
+- **TOGGLE_BACKLIGHT** (2 bytes) - message type, on/off. Sets backlight completely off, no leds will display.
+- **DISPLAY_PAGE** (2 bytes) - message type, page to display. Switch to specific pre-set page.
+- **RESET_PAGE** (2 bytes) - message type, page to reset. Reset/erase specific page.
+- **TOGGLE_NUM_LOCK** (2 bytes) - message type, on/off (NUM_LOCK_LED_ADDRESS). Toggle numlock on/off. Usually run with the `set_leds` function to check state of numlock or capslock. If all leds are on (e.i. TOGGLE_ALL) then this sets numlock to blink instead (this is still a little buggy if toggling on/off quickly).
+- **TOGGLE_CAPS_LOCK** (2 bytes) - message type, on/off (CAPS_LOCK_LED_ADDRESS). Same as numlock.
+- **STEP_BRIGHTNESS** (2 bytes) - message type, and step up (1) or step down (0). Increase or decrease led brightness.
## Sending messages in Keymap.c
-Sending an action to the led mailbox is done using chMBPost with the following form.
+Sending an action to the led mailbox is done using chMBPost:
```
chMBPost(&led_mailbox, message, timeout);
```
@@ -66,14 +73,14 @@ chMBPost(&led_mailbox, message, timeout);
An example:
1. set the message to be sent. First byte (LSB) is the led address, and second is the message type
-`msg=(ON_LED << 8) | 42;`
+ *`msg=(ON_LED << 8) | 42;`
2. send msg to the led mailbox
-`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
+ *`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
Another:
-`msg=(BLINK_TOGGLE_LED << 8) | 46;`
-`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
+ *`msg=(BLINK_TOGGLE_LED << 8) | 46;`
+ *`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
Finally, SET_FULL_ROW requires an extra byte with row information in the message so sending this message looks like:
-`msg=(row<<16) | (SET_FULL_ROW << 8) | (led_pin_byte);`
-`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
+ *`msg=(row<<16) | (SET_FULL_ROW << 8) | (led_pin_byte);`
+ *`chMBPost(&led_mailbox, msg, TIME_IMMEDIATE);`
diff --git a/keyboards/infinity60/led_controller.c b/keyboards/infinity60/led_controller.c
index d4ad0559b..d776b4fcf 100644
--- a/keyboards/infinity60/led_controller.c
+++ b/keyboards/infinity60/led_controller.c
@@ -186,7 +186,7 @@ page_status = 0; //start frame 0 (all off/on)
while(true) {
// wait for a message (asynchronous)
// (messages are queued (up to LED_MAILBOX_NUM_MSGS) if they can't
- // be processed right away)
+ // be processed right away
chMBFetch(&led_mailbox, &msg, TIME_INFINITE);
msg_col = (msg >> 24) & 0xFF;//if needed
msg_pin = (msg >> 16) & 0XFF;//if needed (e.g. SET_FULL_ROW)
@@ -229,7 +229,7 @@ page_status = 0; //start frame 0 (all off/on)
break;
case TOGGLE_ALL:
- //msg_led = unused
+ //msg_led = unused
is31_read_register(0, 0x00, &temp);
led_control_reg[0] = 0;
@@ -315,7 +315,7 @@ page_status = 0; //start frame 0 (all off/on)
break;
}
- //populate 8 byte rows to write on each pin
+ //populate 8 byte arrays to write on each pin
//first byte is register address, every 0x10 9 bytes are A-register pwm pins
__builtin_memset(pwm_register_array+1, pwm_levels[pwm_step_status], 8);