Fix software serial configure

1 files changed, 37 insertions, 31 deletions

diff --git a/converter/sun_usb/config.h b/converter/sun_usb/config.h
index b4f0ff977..65ce9daf6 100644
--- a/converter/sun_usb/config.h
+++ b/converter/sun_usb/config.h
@@ -43,40 +43,46 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *     asynchronous, negative logic, 1200baud, no flow control
  *     1-start bit, 8-data bit, non parity, 1-stop bit
  */
-#define SERIAL_BAUD 1200
-
-#define SERIAL_RXD_DDR  DDRD
-#define SERIAL_RXD_PORT PORTD
-#define SERIAL_RXD_PIN  PIND
-#define SERIAL_RXD_BIT  2
-#define SERIAL_RXD_VECT INT2_vect
-#define SERIAL_RXD_INIT()  do { \
+#define SERIAL_SOFT_BAUD            1200
+#define SERIAL_SOFT_PARITY_NONE
+#define SERIAL_SOFT_BIT_ORDER_LSB
+#define SERIAL_SOFT_LOGIC_NEGATIVE
+/* RXD Port */
+#define SERIAL_SOFT_RXD_ENABLE
+#define SERIAL_SOFT_RXD_DDR         DDRD
+#define SERIAL_SOFT_RXD_PORT        PORTD
+#define SERIAL_SOFT_RXD_PIN         PIND
+#define SERIAL_SOFT_RXD_BIT         2
+#define SERIAL_SOFT_RXD_VECT        INT2_vect
+/* RXD Interupt */
+#define SERIAL_SOFT_RXD_INIT()      do { \
     /* pin configuration: input with pull-up */ \
-    SERIAL_RXD_DDR &= ~(1<<SERIAL_RXD_BIT);     \
-    SERIAL_RXD_PORT |= (1<<SERIAL_RXD_BIT);     \
-    /* enable interrupt: INT2(rising edge) */   \
-    EICRA |= ((1<<ISC21)|(1<<ISC20));           \
-    EIMSK |= (1<<INT2);                         \
+    SERIAL_SOFT_RXD_DDR &= ~(1<<SERIAL_SOFT_RXD_BIT); \
+    SERIAL_SOFT_RXD_PORT |= (1<<SERIAL_SOFT_RXD_BIT); \
+    /* enable interrupt: INT2(rising edge) */ \
+    EICRA |= ((1<<ISC21)|(1<<ISC20)); \
+    EIMSK |= (1<<INT2); \
+    sei(); \
 } while (0)
-#define SERIAL_RXD_INT_ENTER()
-#define SERIAL_RXD_INT_EXIT() do {  \
-    /* clear interrupt  flag */     \
-    EIFR = (1<<INTF2);              \
+#define SERIAL_SOFT_RXD_INT_ENTER()
+#define SERIAL_SOFT_RXD_INT_EXIT()  do { \
+    /* clear interrupt  flag */ \
+    EIFR = (1<<INTF2); \
 } while (0)
-#define SERIAL_RXD_READ()    (~SERIAL_RXD_PIN&(1<<SERIAL_RXD_BIT))
-
-#define SERIAL_TXD_DDR  DDRD
-#define SERIAL_TXD_PORT PORTD
-#define SERIAL_TXD_PIN  PIND
-#define SERIAL_TXD_BIT  3
-/* negative logic */
-#define SERIAL_TXD_ON()     do { SERIAL_TXD_PORT &= ~(1<<SERIAL_TXD_BIT); } while (0)
-#define SERIAL_TXD_OFF()    do { SERIAL_TXD_PORT |=  (1<<SERIAL_TXD_BIT); } while (0)
-#define SERIAL_TXD_INIT()   do { \
-    /* pin configuration: output */         \
-    SERIAL_TXD_DDR |= (1<<SERIAL_TXD_BIT);  \
-    /* idle */                              \
-    SERIAL_TXD_ON();                        \
+#define SERIAL_SOFT_RXD_READ()      (SERIAL_SOFT_RXD_PIN&(1<<SERIAL_SOFT_RXD_BIT))
+/* TXD Port */
+#define SERIAL_SOFT_TXD_ENABLE
+#define SERIAL_SOFT_TXD_DDR         DDRD
+#define SERIAL_SOFT_TXD_PORT        PORTD
+#define SERIAL_SOFT_TXD_PIN         PIND
+#define SERIAL_SOFT_TXD_BIT         3
+#define SERIAL_SOFT_TXD_HI()        do { SERIAL_SOFT_TXD_PORT |=  (1<<SERIAL_SOFT_TXD_BIT); } while (0)
+#define SERIAL_SOFT_TXD_LO()        do { SERIAL_SOFT_TXD_PORT &= ~(1<<SERIAL_SOFT_TXD_BIT); } while (0)
+#define SERIAL_SOFT_TXD_INIT()      do { \
+    /* pin configuration: output */ \
+    SERIAL_SOFT_TXD_DDR |= (1<<SERIAL_SOFT_TXD_BIT); \
+    /* idle */ \
+    SERIAL_SOFT_TXD_ON(); \
 } while (0)
 
 #endif