diff options
author | a0-c <g1@porkhash.net> | 2016-04-27 02:05:05 +0200 |
---|---|---|
committer | Jack Humbert <jack.humb@gmail.com> | 2016-04-27 02:05:05 +0200 |
commit | 8fda26db7d4334eaa5018d325b368c40103b198f (patch) | |
tree | 2e674eb2030898a872db064859e68bffb3827aac /keyboard/gh60_rev_c/Makefile | |
parent | e024c11f7a849a38e478cda9fb9939a838cfa2e0 (diff) | |
download | qmk_firmware-8fda26db7d4334eaa5018d325b368c40103b198f.tar.gz qmk_firmware-8fda26db7d4334eaa5018d325b368c40103b198f.tar.xz |
gh60 Rev C with LED controls (#289)
* gh60_rev_c
* gh60 Rev C
Support for WASD, Poker, Esc, FN LED clusters
* clean up spacing
* Update README.md
* Added image and pinout
* PCB image
Diffstat (limited to 'keyboard/gh60_rev_c/Makefile')
-rw-r--r-- | keyboard/gh60_rev_c/Makefile | 140 |
1 files changed, 140 insertions, 0 deletions
diff --git a/keyboard/gh60_rev_c/Makefile b/keyboard/gh60_rev_c/Makefile new file mode 100644 index 000000000..09843dd83 --- /dev/null +++ b/keyboard/gh60_rev_c/Makefile @@ -0,0 +1,140 @@ +#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+# Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+# (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+# have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+# have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+# (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+# (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+# with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+# bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = gh60
+
+
+# Directory common source filess exist
+TOP_DIR = ../..
+TMK_DIR = ../../tmk_core
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# # project specific files
+SRC = gh60.c
+
+ifdef KEYMAP
+ SRC := keymaps/$(KEYMAP).c $(SRC)
+else
+ SRC := keymaps/default.c $(SRC)
+endif
+
+CONFIG_H = config.h
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+# CONSOLE_ENABLE = yes # Console for debug(+400)
+# COMMAND_ENABLE = yes # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
+# MIDI_ENABLE = YES # MIDI controls
+# UNICODE_ENABLE = YES # Unicode
+# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
+
+
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+VPATH += $(TMK_DIR)
+
+include $(TOP_DIR)/quantum/quantum.mk
+
|