Merge remote-tracking branch 'upstream/master'

* upstream/master: (1239 commits)
  Update ez.c
  removes planck/rev3 temporarily
  Move hand_swap_config to ez.c, removes error for infinity
  Update Makefile
  ergodox: Update algernon's keymap to v1.9
  Added VS Code dir to .gitignore
  Support the Pegasus Hoof controller.
  [Jack & Erez] Simplifies and documents TO
  add readme
  use wait_ms instead of _delay_ms
  add messenger
  init keymap
  Add example keymap
  Adding whiskey_tango_foxtrot_capslock ergodox keymap
  Unicode map framework. Allow unicode up to 0xFFFFF using separate mapping table
  CIE 1931 dim curve
  Apply the dim curve to the RGB output
  Update the Cluecard readme files
  Tune snake and knight intervals for Cluecard
  Tunable RGB light intervals
  ...

1 files changed, 78 insertions, 0 deletions

diff --git a/keyboards/ergodox/ez/rules.mk b/keyboards/ergodox/ez/rules.mk
new file mode 100644
index 000000000..a9715beb8
--- /dev/null
+++ b/keyboards/ergodox/ez/rules.mk
@@ -0,0 +1,78 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make = Make software.
+#
+# make clean = Clean out built project files.
+#
+# That's pretty much all you need. To compile, always go make clean, 
+# followed by make.
+#
+# For advanced users only:
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+#----------------------------------------------------------------------------
+
+# # project specific files
+SRC = twimaster.c \
+	  matrix.c
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   comment out to disable the options.
+#
+
+SLEEP_LED_ENABLE = no
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif