new handwired keyboard - Dactyl Manuform (#2516)

* adding new handwired keyboard: dactyl-manuform

* adding qwerty layout

* updating readme file.

1 files changed, 147 insertions, 0 deletions

diff --git a/keyboards/handwired/dactyl_manuform/readme.md b/keyboards/handwired/dactyl_manuform/readme.md
new file mode 100644
index 000000000..354e11ee9
--- /dev/null
+++ b/keyboards/handwired/dactyl_manuform/readme.md
@@ -0,0 +1,147 @@
+Dactyl manuform
+======
+
+the [Dactyl-Manuform](https://github.com/tshort/dactyl-keyboard) is a split curved keyboard based on the design of [adereth dactyl](https://github.com/adereth/dactyl-keyboard) and thumb cluster design of the [manuform](https://geekhack.org/index.php?topic=46015.0) keyboard, the hardware is similar to the let's split keyboard. all information needed for making one is in the first link.
+
+## First Time Setup
+
+Download or clone the `qmk_firmware` repo and navigate to its top level directory. Once your build environment is setup, you'll be able to generate the default .hex using:
+
+```
+$ make dactyl_manuform:dvorak
+```
+
+You will see a lot of output and if everything worked correctly you will see the built hex file:
+
+```
+dactyl_manuform_dvorak.hex
+```
+
+If you would like to use one of the alternative keymaps, or create your own, copy one of the existing [keymaps](keymaps/) and run make like so:
+
+```
+$ make dactyl_manuform:YOUR_KEYMAP_NAME
+```
+
+If everything worked correctly you will see a file:
+
+```
+dactyl_manuform_YOUR_KEYMAP_NAME.hex
+```
+
+For more information on customizing keymaps, take a look at the primary documentation for [Customizing Your Keymap](/docs/faq_keymap.md) in the main readme.md.
+
+Required Hardware
+-----------------
+
+Apart from diodes and key switches for the keyboard matrix in each half, you
+will need:
+
+* 2 Arduino Pro Micros. You can find these on AliExpress for ≈3.50USD each.
+* 2 TRRS sockets and 1 TRRS cable, or 2 TRS sockets and 1 TRS cable
+
+Alternatively, you can use any sort of cable and socket that has at least 3
+wires. If you want to use I2C to communicate between halves, you will need a
+cable with at least 4 wires and 2x 4.7kΩ pull-up resistors
+
+Optional Hardware
+-----------------
+A speaker can be hooked-up to either side to the `5` (`C6`) pin and `GND`, and turned on via `AUDIO_ENABLE`.
+
+Wiring
+------
+
+The 3 wires of the TRS/TRRS cable need to connect GND, VCC, and digital pin 3 (i.e.
+PD0 on the ATmega32u4) between the two Pro Micros.
+
+Next, wire your key matrix to any of the remaining 17 IO pins of the pro micro
+and modify the `matrix.c` accordingly.
+
+The wiring for serial:
+
+![serial wiring](https://i.imgur.com/C3D1GAQ.png)
+
+The wiring for i2c:
+
+![i2c wiring](https://i.imgur.com/Hbzhc6E.png)
+
+The pull-up resistors may be placed on either half. It is also possible
+to use 4 resistors and have the pull-ups in both halves, but this is
+unnecessary in simple use cases.
+
+You can change your configuration between serial and i2c by modifying your `config.h` file.
+
+Notes on Software Configuration
+-------------------------------
+
+the keymaps in here are for the 4x5 layout of the keyboard only.
+
+Flashing
+-------
+From the top level `qmk_firmware` directory run `make KEYBOARD:KEYMAP:avrdude` for automatic serial port resolution and flashing.
+Example: `make lets_split/rev2:default:avrdude`
+
+
+Choosing which board to plug the USB cable into (choosing Master)
+--------
+Because the two boards are identical, the firmware has logic to differentiate the left and right board.
+
+It uses two strategies to figure things out: looking at the EEPROM (memory on the chip) or looking if the current board has the usb cable.
+
+The EEPROM approach requires additional setup (flashing the eeprom) but allows you to swap the usb cable to either side.
+
+The USB cable approach is easier to setup and if you just want the usb cable on the left board, you do not need to do anything extra.
+
+### Setting the left hand as master
+If you always plug the usb cable into the left board, nothing extra is needed as this is the default. Comment out `EE_HANDS` and comment out `I2C_MASTER_RIGHT` or `MASTER_RIGHT` if for some reason it was set.
+
+### Setting the right hand as master
+If you always plug the usb cable into the right board, add an extra flag to your `config.h`
+```
+ #define MASTER_RIGHT
+```
+
+### Setting EE_hands to use either hands as master
+If you define `EE_HANDS` in your `config.h`, you will need to set the
+EEPROM for the left and right halves.
+
+The EEPROM is used to store whether the
+half is left handed or right handed. This makes it so that the same firmware
+file will run on both hands instead of having to flash left and right handed
+versions of the firmware to each half. To flash the EEPROM file for the left
+half run:
+```
+avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-lefthand.eep
+// or the equivalent in dfu-programmer
+
+```
+and similarly for right half
+```
+avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-righhand.eep
+// or the equivalent in dfu-programmer
+```
+
+NOTE: replace `$(COM_PORT)` with the port of your device (e.g. `/dev/ttyACM0`)
+
+After you have flashed the EEPROM, you then need to set `EE_HANDS` in your config.h, rebuild the hex files and reflash.
+
+Note that you need to program both halves, but you have the option of using
+different keymaps for each half. You could program the left half with a QWERTY
+layout and the right half with a Colemak layout using bootmagic's default layout option.
+Then if you connect the left half to a computer by USB the keyboard will use QWERTY and Colemak when the
+right half is connected.
+
+
+Notes on Using Pro Micro 3.3V
+-----------------------------
+
+Do update the `F_CPU` parameter in `rules.mk` to `8000000` which reflects
+the frequency on the 3.3V board.
+
+Also, if the slave board is producing weird characters in certain columns,
+update the following line in `matrix.c` to the following:
+
+```
+// _delay_us(30);  // without this wait read unstable value.
+_delay_us(300);  // without this wait read unstable value.
+```