dd Honeycomb macropad (#5000)

* Add Honeycome macropad

* Replace pragma, update info

* Update code based on review

1 files changed, 92 insertions, 0 deletions

diff --git a/keyboards/honeycomb/honeycomb.c b/keyboards/honeycomb/honeycomb.c
new file mode 100755
index 000000000..add4af153
--- /dev/null
+++ b/keyboards/honeycomb/honeycomb.c
@@ -0,0 +1,92 @@
+#include "honeycomb.h"
+#include "pointing_device.h"
+#include "report.h"
+
+void uart_init(void) {
+	SERIAL_UART_INIT();
+}
+
+void pointing_device_task(void){
+	/*report_mouse_t currentReport = {};
+    SERIAL_UART_INIT();
+    uint32_t timeout = 0;
+
+    //the m character requests the RF slave to send the mouse report
+    SERIAL_UART_DATA = 'm';
+
+    //trust the external inputs completely, erase old data
+    uint8_t uart_data[5] = {0};
+
+    //there are 10 bytes corresponding to 10 columns, and an end byte
+    for (uint8_t i = 0; i < 5; i++) {
+        //wait for the serial data, timeout if it's been too long
+        //this only happened in testing with a loose wire, but does no
+        //harm to leave it in here
+        while(!SERIAL_UART_RXD_PRESENT){
+            timeout++;
+            if (timeout > 10000){
+		xprintf("\r\nTIMED OUT");
+                break;
+            }
+        }
+	xprintf("\r\nGOT DATA for %d",i);
+        uart_data[i] = SERIAL_UART_DATA;
+    }
+
+    //check for the end packet, bytes 1-4 are movement and scroll
+    //but byte 5 has bits 0-3 for the scroll button state
+	//(1000 if pressed, 0000 if not) and bits 4-7 are always 1
+	//We can use this to verify the report sent properly.
+    if (uart_data[4] == 0x0F || uart_data[4] == 0x8F)
+    {
+	xprintf("\r\nREQUESTED MOUSE, RECEIVED %i, %i, %i, %i, %i",uart_data[0],uart_data[1],uart_data[2],uart_data[3],uart_data[4]);
+		currentReport = pointing_device_get_report();
+        //shifting and transferring the info to the mouse report varaible
+        //mouseReport.x = 127 max -127 min
+		currentReport.x = (int8_t) uart_data[0];
+        //mouseReport.y = 127 max -127 min
+		currentReport.y = (int8_t) uart_data[1];
+        //mouseReport.v = 127 max -127 min (scroll vertical)
+		currentReport.v = (int8_t) uart_data[2];
+        //mouseReport.h = 127 max -127 min (scroll horizontal)
+		currentReport.h = (int8_t) uart_data[3];
+        //mouseReport.buttons = 0x31 max (bitmask for mouse buttons 1-5) 0x00 min
+		//mouse buttons 1 and 2 are handled by the keymap, but not 3
+		if (uart_data[4] == 0x0F) { //then 3 is not pressed
+			currentReport.buttons &= ~MOUSE_BTN3; //MOUSE_BTN3 is def in report.h
+		} else { //3 must be pressed
+			currentReport.buttons |= MOUSE_BTN3;
+		}
+		pointing_device_set_report(currentReport);
+    } else {
+	xprintf("\r\nRequested packet, data 4 was %d",uart_data[4]);
+    }*/
+    pointing_device_send();
+}
+
+void led_init(void) {
+  setPinOutput(D1);
+  writePinHigh(D1);
+  setPinOutput(F4);
+  writePinHigh(F4);
+  setPinOutput(F5);
+  writePinHigh(F5);
+}
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+	matrix_init_user();
+	uart_init();
+	led_init();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+	matrix_scan_user();
+}
+
+void led_set_kb(uint8_t usb_led) {
+
+}