Merge branch 'master' of github.com:jackhumbert/qmk_firmware

# Conflicts:
#	keyboard/ergodox_ez/keymaps/zweihander-osx/keymap.c
#	keyboard/ergodox_ez/keymaps/zweihander-osx/zweihander-osx.hex

24 files changed, 750 insertions, 0 deletions

diff --git a/keyboards/kc60/Makefile b/keyboards/kc60/Makefile
new file mode 100644
index 000000000..b00a488b9
--- /dev/null
+++ b/keyboards/kc60/Makefile
@@ -0,0 +1,76 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
+
diff --git a/keyboards/kc60/config.h b/keyboards/kc60/config.h
new file mode 100644
index 000000000..c4a9b9ff8
--- /dev/null
+++ b/keyboards/kc60/config.h
@@ -0,0 +1,164 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    You
+#define PRODUCT         kc60v2
+#define DESCRIPTION     A custom keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+
+// Possible pins for columns include: F1  F0  E6  D7  D6  D4  C7  C6  B7  B5  B4  B3  B1  B0
+// Pins for rows include:  D0  D1  F6  F7  D5
+// KC60 Version 2 
+#define MATRIX_ROW_PINS { D0, D1, F6, F7, D5 }
+#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3 }
+#define UNUSED_PINS
+
+#define BACKLIGHT_PIN B6
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/kc60/kc60.c b/keyboards/kc60/kc60.c
new file mode 100644
index 000000000..746ac634a
--- /dev/null
+++ b/keyboards/kc60/kc60.c
@@ -0,0 +1 @@
+#include "kc60.h"
diff --git a/keyboards/kc60/kc60.h b/keyboards/kc60/kc60.h
new file mode 100644
index 000000000..34eab4b2a
--- /dev/null
+++ b/keyboards/kc60/kc60.h
@@ -0,0 +1,23 @@
+#ifndef KC60_H
+#define KC60_H
+
+#include "quantum.h"
+
+// This a shortcut to help you visually see your layout.
+// The first section contains all of the arguements
+// The second converts the arguments into a multi-dimensional array
+#define KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
+    K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+    K40, K41, K42,           K45,                     K4A, K4B, K4C, K4D  \
+    ) { \
+  {  K00,  K01,  K02,  K03,    K04,    K05,  K06,    K07,    K08,    K09,  K0A,  K0B,  K0C,  K0D  },  \
+  {  K10,  K11,  K12,  K13,    K14,    K15,  K16,    K17,    K18,    K19,  K1A,  K1B,  K1C,  K1D  },  \
+  {  K20,  K21,  K22,  K23,    K24,    K25,  K26,    K27,    K28,    K29,  K2A,  K2B,  K2C,  K2D  },  \
+  {  K30,  K31,  K32,  K33,    K34,    K35,  K36,    K37,    K38,    K39,  K3A,  K3B,  K3C,  K3D  },  \
+  {  K40,  K41,  K42,  KC_NO,  KC_NO,  K45,  KC_NO,  KC_NO,  KC_NO,  KC_NO,K4A,  K4B,  K4C,  K4D  }   \
+}
+
+#endif
diff --git a/keyboards/kc60/keymaps/default/keymap.c b/keyboards/kc60/keymaps/default/keymap.c
new file mode 100644
index 000000000..6f8352c69
--- /dev/null
+++ b/keyboards/kc60/keymaps/default/keymap.c
@@ -0,0 +1,24 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "kc60.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [0] = KEYMAP( /* Basic QWERTY */
+      KC_ESC,   KC_1,     KC_2,     KC_3,    KC_4,     KC_5,     KC_6,     KC_7,    KC_8,  KC_9,     KC_0,     KC_MINS,  KC_EQL,   KC_BSPC,  \
+      KC_TAB,   KC_Q,     KC_W,     KC_E,    KC_R,     KC_T,     KC_Y,     KC_U,    KC_I,  KC_O,     KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,  \
+      KC_CAPS,  KC_A,     KC_S,     KC_D,    KC_F,     KC_G,     KC_H,     KC_J,    KC_K,  KC_L,     KC_SCLN,  KC_QUOT,  KC_NO,    KC_ENT,   \
+      KC_LSFT,  KC_NO,    KC_Z,     KC_X,    KC_C,     KC_V,     KC_B,     KC_N,    KC_M,  KC_COMM,  KC_DOT,   KC_SLSH,  KC_NO,    KC_RSFT,  \
+      KC_LCTL,  KC_LALT,  KC_LGUI,                     KC_SPC,                                       KC_RGUI,  KC_RALT,  KC_RCTL,  RESET \
+      ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+  return MACRO_NONE;
+};
diff --git a/keyboards/kc60/keymaps/sgoodwin/keymap.c b/keyboards/kc60/keymaps/sgoodwin/keymap.c
new file mode 100644
index 000000000..99e95c232
--- /dev/null
+++ b/keyboards/kc60/keymaps/sgoodwin/keymap.c
@@ -0,0 +1,42 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "kc60.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  /*
+   * Toggles between colemak and qwerty by tapping the bottom right key.
+   * Holding capslock key gives a layer like the KBParadise v60.
+   */
+  [0] = KEYMAP( /* Basic Colemak */
+      KC_ESC,   KC_1,     KC_2,     KC_3,    KC_4,     KC_5,     KC_6,     KC_7,  KC_8,  KC_9,     KC_0,     KC_MINS,  KC_EQL,   KC_BSPC,  \
+      KC_TAB,   KC_Q,     KC_W,     KC_F,    KC_P,     KC_G,     KC_J,     KC_L,  KC_U,  KC_Y,     KC_SCLN,  KC_LBRC,  KC_RBRC,  KC_BSLS,  \
+      MO(2),    KC_A,     KC_R,     KC_S,    KC_T,     KC_D,     KC_H,     KC_N,  KC_E,  KC_I,     KC_O,     KC_QUOT,  KC_NO,    KC_ENT,   \
+      KC_LSFT,  KC_NO,    KC_Z,     KC_X,    KC_C,     KC_V,     KC_B,     KC_K,  KC_M,  KC_COMM,  KC_DOT,   KC_SLSH,  KC_NO,    KC_RSFT,  \
+      KC_LCTL,  KC_LALT,  KC_LGUI,                     KC_SPC,                                     KC_RGUI,  KC_RALT,  KC_RCTL,  DF(1)  \
+      ),
+  [1] = KEYMAP( /* Basic QWERTY */
+      KC_ESC,   KC_1,     KC_2,     KC_3,    KC_4,     KC_5,     KC_6,     KC_7,    KC_8,  KC_9,     KC_0,     KC_MINS,  KC_EQL,   KC_BSPC,  \
+      KC_TAB,   KC_Q,     KC_W,     KC_E,    KC_R,     KC_T,     KC_Y,     KC_U,    KC_I,  KC_O,     KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,  \
+      MO(2),    KC_A,     KC_S,     KC_D,    KC_F,     KC_G,     KC_H,     KC_J,    KC_K,  KC_L,     KC_SCLN,  KC_QUOT,  KC_NO,    KC_ENT,   \
+      KC_LSFT,  KC_NO,    KC_Z,     KC_X,    KC_C,     KC_V,     KC_B,     KC_N,    KC_M,  KC_COMM,  KC_DOT,   KC_SLSH,  KC_NO,    KC_RSFT,  \
+      KC_LCTL,  KC_LALT,  KC_LGUI,                     KC_SPC,                                       KC_RGUI,  KC_RALT,  KC_RCTL,  DF(0) \
+      ),
+  [2] = KEYMAP( /* KBP v60-like arrows, media keys, etc */
+      KC_GRV,   KC_F1,    KC_F2,    KC_F3,     KC_F4,    KC_F5,    KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   KC_F11,    KC_F12,  KC_DEL,   \
+      KC_TRNS,  KC_TRNS,  KC_UP,    KC_TRNS,   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_UP,    BL_INC,    BL_DEC,  BL_STEP,  \
+      KC_TRNS,  KC_LEFT,  KC_DOWN,  KC_RIGHT,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_LEFT,  KC_DOWN,  KC_RIGHT,  KC_NO,   KC_TRNS,  \
+      KC_TRNS,  KC_NO,    KC_MPRV,  KC_MPLY,   KC_MNXT,  KC_VOLD,  KC_VOLU,  KC_MUTE,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,   KC_NO,   KC_TRNS,  \
+      KC_TRNS,  KC_TRNS,  KC_TRNS,                       KC_SPC,                                           DEBUG,    RESET,     KC_TRNS, KC_NO     \
+      ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+  return MACRO_NONE;
+};
diff --git a/keyboards/kc60/keymaps/stanleylai/Makefile b/keyboards/kc60/keymaps/stanleylai/Makefile
new file mode 100644
index 000000000..b8b2beda4
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/Makefile
@@ -0,0 +1,25 @@
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no        # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= no         # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= yes 			 # Enable WS2812 underglow RGB strip
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= yes           # USB Nkey Rollover
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
diff --git a/keyboards/kc60/keymaps/stanleylai/base_layer.png b/keyboards/kc60/keymaps/stanleylai/base_layer.png
new file mode 100644
index 000000000..97235c6af
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/base_layer.png
diff --git a/keyboards/kc60/keymaps/stanleylai/config.h b/keyboards/kc60/keymaps/stanleylai/config.h
new file mode 100644
index 000000000..b5024a6d0
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/config.h
@@ -0,0 +1,3 @@
+// Use configs from WS2812 enabled Keymap
+
+#include "../ws2812/config.h"
diff --git a/keyboards/kc60/keymaps/stanleylai/keymap.c b/keyboards/kc60/keymaps/stanleylai/keymap.c
new file mode 100644
index 000000000..057c73bf4
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/keymap.c
@@ -0,0 +1,86 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "kc60.h"
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BL   0
+#define _FL   1
+#define _RGBL 2
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+// See base_layer.png and rgb_layer.png for layout reference
+
+// Base Default Layer
+// Mac Modifier Layout. Use BootMagic to toggle GUI and ALT positions.
+[_BL] = KEYMAP(
+  F(0),             KC_1,   KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   KC_MINS,  KC_EQL,   KC_BSPC, \
+  KC_TAB,           KC_Q,   KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,   KC_LBRC,  KC_RBRC,  KC_BSLS, \
+  LT(_FL, KC_CAPS), KC_A,   KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,   KC_SCLN,KC_QUOT,  KC_NO,    KC_ENT,  \
+  KC_LSFT, KC_NO,   KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM,KC_DOT, KC_SLSH,  MO(_FL),  KC_UP,   \
+  KC_LCTL, KC_LALT, KC_LGUI,                KC_SPC,                                 KC_RGUI,KC_LEFT,  KC_DOWN,  KC_RGHT),
+
+// Function layer
+[_FL] = KEYMAP(
+  KC_GRV, KC_F1,  KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,  KC_F10, KC_F11,   KC_F12,   KC_DEL, \
+  KC_NO,  KC_MPRV,KC_UP,  KC_MNXT,KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_PSCR,KC_SLCK,  KC_PAUS,  KC_INS, \
+  KC_TRNS,KC_LEFT,KC_DOWN,KC_RGHT,KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO,  \
+  KC_TRNS,KC_NO,  KC_MUTE,KC_VOLD,KC_VOLU,KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_TRNS,  LT(_RGBL, KC_PGUP),\
+  KC_TRNS,KC_TRNS,KC_TRNS,                KC_MPLY,                                KC_TRNS,KC_HOME,  KC_PGDN,  KC_END),
+
+// RGB Layer
+[_RGBL] = KEYMAP(
+  #ifdef RGBLIGHT_ENABLE
+  RESET,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO, \
+  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO, \
+  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO,  \
+  KC_TRNS,KC_NO,  RGB_TOG,RGB_MOD,RGB_HUI,RGB_HUD,RGB_SAI,RGB_SAD,RGB_VAI,RGB_VAD,BL_STEP,BL_TOGG,  KC_TRNS,  KC_TRNS,\
+  KC_TRNS,KC_TRNS,KC_TRNS,                KC_TRNS,                                KC_TRNS,KC_TRNS,  KC_TRNS,  KC_TRNS),
+  #else
+  RESET,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO, \
+  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO, \
+  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,    KC_NO,    KC_NO,  \
+  KC_TRNS,KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  KC_NO,  BL_STEP,BL_TOGG,  KC_TRNS,  KC_TRNS,\
+  KC_TRNS,KC_TRNS,KC_TRNS,                KC_TRNS,                                KC_TRNS,KC_TRNS,  KC_TRNS,  KC_TRNS),
+  #endif
+};
+
+
+enum function_id {
+    SHIFT_ESC,
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+  [0]  = ACTION_FUNCTION(SHIFT_ESC),
+};
+
+#define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  static uint8_t shift_esc_shift_mask;
+  switch (id) {
+    case SHIFT_ESC:
+      shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
+      if (record->event.pressed) {
+        if (shift_esc_shift_mask) {
+          add_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          add_key(KC_ESC);
+          send_keyboard_report();
+        }
+      } else {
+        if (shift_esc_shift_mask) {
+          del_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          del_key(KC_ESC);
+          send_keyboard_report();
+        }
+      }
+      break;
+  }
+}
diff --git a/keyboards/kc60/keymaps/stanleylai/readme.md b/keyboards/kc60/keymaps/stanleylai/readme.md
new file mode 100644
index 000000000..1db72610d
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/readme.md
@@ -0,0 +1,26 @@
+Stanley Lai's Split Right Shift with Dedicated Arrow Keys
+======================
+
+![Image of KC60 with RGB Underglow](../ws2812/ws2812_example.jpg)
+
+## Quantum MK Firmware
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Keymap Notes
+- Keymap setup with split Right Shift in mind.
+- Right-side modifiers are setup as dedicated arrow keys
+
+### Base Layer Reference
+- Fn Layer indicated on keycap front legends.
+- Tapping Caps Lock key toggles Caps. Holding it down momentarily switches us to the Fn Layer.
+- Holding down "Fn" and "Page Down" momentarily switches us to the RGB Layer. Tapping "Page Down" behaves as expected.
+![Base Layer](base_layer.jpg)
+
+### RGB Layer Reference
+![RGB Layer](rgb_layer.jpg)
+
+## WS2812 Support
+By default, it is now setup for 16 LEDs on the PF5 breakout pin. See [included image](../ws2812/ws2812_wiring.jpg) for wiring reference.
+
+### Build
+To build this keymap, simply run `make KEYMAP=stanleylai`.
diff --git a/keyboards/kc60/keymaps/stanleylai/rgb_layer.png b/keyboards/kc60/keymaps/stanleylai/rgb_layer.png
new file mode 100644
index 000000000..2bba028bb
--- /dev/null
+++ b/keyboards/kc60/keymaps/stanleylai/rgb_layer.png
diff --git a/keyboards/kc60/keymaps/wigguno/Makefile b/keyboards/kc60/keymaps/wigguno/Makefile
new file mode 100644
index 000000000..0d7d918d8
--- /dev/null
+++ b/keyboards/kc60/keymaps/wigguno/Makefile
@@ -0,0 +1,24 @@
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no        # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no         # Console for debug(+400)
+COMMAND_ENABLE ?= no         # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
diff --git a/keyboards/kc60/keymaps/wigguno/keymap.c b/keyboards/kc60/keymaps/wigguno/keymap.c
new file mode 100644
index 000000000..50b1d0f98
--- /dev/null
+++ b/keyboards/kc60/keymaps/wigguno/keymap.c
@@ -0,0 +1,62 @@
+// This keymap was designed to close to the default kc60 layout, with some useful changes, such as adding media keys.
+// It also moves the reset key off the base layer, as in the default kc60 layout for this firmware.
+// I have swapped FN and RGUI as my rainbow keyset has them in the opposite order. 
+
+#include "kc60.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+	
+   /* Basic QWERTY
+	* ,-----------------------------------------------------------.
+	* |Esc | 1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backsp |
+	* |-----------------------------------------------------------|
+	* |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|  \  |
+	* |-----------------------------------------------------------|
+	* |CAPS   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return |
+	* |-----------------------------------------------------------|
+	* |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift     |
+	* |-----------------------------------------------------------|
+	* |Ctrl|Gui |Alt |      Space            |Alt |FN  |Gui |Ctrl |
+	* `-----------------------------------------------------------'
+	*/
+  [0] = KEYMAP( 
+      KC_ESC,   KC_1,     KC_2,     KC_3,     KC_4,     KC_5,     KC_6,     KC_7,     KC_8,     KC_9,     KC_0,     KC_MINS,  KC_EQL,   KC_BSPC,   \
+      KC_TAB,   KC_Q,     KC_W,     KC_E,     KC_R,     KC_T,     KC_Y,     KC_U,     KC_I,     KC_O,     KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,   \
+      KC_CAPS,  KC_A,     KC_S,     KC_D,     KC_F,     KC_G,     KC_H,     KC_J,     KC_K,     KC_L,     KC_SCLN,  KC_QUOT,  KC_NO,    KC_ENT,    \
+      KC_LSFT,  KC_NO,    KC_Z,     KC_X,     KC_C,     KC_V,     KC_B,     KC_N,     KC_M,     KC_COMM,  KC_DOT,   KC_SLSH,  KC_NO,    KC_RSFT,   \
+      KC_LCTL,  KC_LGUI,  KC_LALT,                      KC_SPC,                                           KC_RALT,  MO(1),    KC_RGUI,  KC_RCTL    \
+      ),
+	  	
+   /*
+	* ,-----------------------------------------------------------.
+	* | `  |F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12| Del   |
+	* |-----------------------------------------------------------|
+	* |     |   | Up|   |   |   |   |   |   |   | PS|   |   |     |
+	* |-----------------------------------------------------------|
+	* |       |Lft|Dwn|Rgt|   |BL-|BL+|   |   |   |   |   |       |
+	* |-----------------------------------------------------------|
+	* |        |Prv| PP|Nxt|   |   |   |   |Hom|End|   |          |
+	* |-----------------------------------------------------------|
+	* | Rst|    |    |          BL           |    |    |    |     |
+	* `-----------------------------------------------------------'
+	* PS = Print Screen
+	* PP = Play/Pause
+	*/
+  [1] = KEYMAP( /* Function Layer */
+      KC_GRV,   KC_F1,    KC_F2,    KC_F3,    KC_F4,    KC_F5,    KC_F6,    KC_F7,    KC_F8,    KC_F9,    KC_F10,   KC_F11,   KC_F12,   KC_DELETE, \
+      KC_TRNS,  KC_TRNS,  KC_UP,    KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_PSCR,  KC_TRNS,  KC_TRNS,  KC_TRNS,   \
+      KC_TRNS,  KC_LEFT,  KC_DOWN,  KC_RGHT,  KC_TRNS,  BL_DEC,   BL_INC,   KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,   \
+      KC_TRNS,  KC_TRNS,  KC_MPRV,  KC_MPLY,  KC_MNXT,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_HOME,  KC_END,   KC_TRNS,  KC_TRNS,  KC_TRNS,   \
+      RESET,    KC_TRNS,  KC_TRNS,                      BL_TOGG,                                          KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS    \
+      ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+ 
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+  // MACRODOWN only works in this function
+  return MACRO_NONE;
+};
diff --git a/keyboards/kc60/keymaps/wigguno/readme.md b/keyboards/kc60/keymaps/wigguno/readme.md
new file mode 100644
index 000000000..55a9f60c7
--- /dev/null
+++ b/keyboards/kc60/keymaps/wigguno/readme.md
@@ -0,0 +1,14 @@
+Wigguno's KC60 Layout
+======================
+
+## Quantum MK Firmware
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Changes from default QMK layout
+The default QMK layout for KC60 does not have a function layer. It also has the bootloader-mode reset key bound. This keymap fixes both of these by adding a sensible function layer (including moving the reset key onto it, far away from the FN key).
+
+### Changes from the default KC60 layout
+The default KC60 layout is good, but it was missing media keys. I've added previous, play/pause and next. I've also removed some of the keys from the function layer I didn't use.
+
+### Build
+To enable NKRO you must be in the keymaps/wigguno directory when running make.
diff --git a/keyboards/kc60/keymaps/ws2812/Makefile b/keyboards/kc60/keymaps/ws2812/Makefile
new file mode 100644
index 000000000..891c44416
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/Makefile
@@ -0,0 +1,25 @@
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes  # Allow locking of keyboard via magic key
+BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
+RGBLIGHT_ENABLE ?= yes 			 # Enable WS2812 underglow RGB strip
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
diff --git a/keyboards/kc60/keymaps/ws2812/config.h b/keyboards/kc60/keymaps/ws2812/config.h
new file mode 100644
index 000000000..2f39ea8e5
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/config.h
@@ -0,0 +1,9 @@
+#include "../../config.h"
+
+/* WS2812B RGB Underglow LED */
+#define RGB_DI_PIN F5   // Based on wiring depicted in ws2812_wiring.jpg
+#define RGBLIGHT_TIMER       
+#define RGBLED_NUM 16         // Number of LEDs. Change this to match your use case.
+#define RGBLIGHT_HUE_STEP 8
+#define RGBLIGHT_SAT_STEP 8
+#define RGBLIGHT_VAL_STEP 8
diff --git a/keyboards/kc60/keymaps/ws2812/keymap.c b/keyboards/kc60/keymaps/ws2812/keymap.c
new file mode 100644
index 000000000..1c0574df0
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/keymap.c
@@ -0,0 +1,98 @@
+// This is the canonical layout file for the Quantum project. If you want to add another keyboard,
+// this is the style you want to emulate.
+
+#include "kc60.h"
+
+// Used for SHIFT_ESC
+#define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+#define _BL 0
+#define _FL 1
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  /* Keymap _BL: (Base Layer) Default Layer
+   * ,-----------------------------------------------------------.
+   * |Esc~| 1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|Backsp |
+   * |-----------------------------------------------------------|
+   * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|  \  |
+   * |-----------------------------------------------------------|
+   * |CAPS   |  A|  S|  D|  F|  G|  H|  J|  K|  L|  ;|  '|Return |
+   * |-----------------------------------------------------------|
+   * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|  /|Shift     |
+   * |-----------------------------------------------------------|
+   * |Ctrl|Gui |Alt |      Space            |Alt |Gui |FN  |Ctrl |
+   * `-----------------------------------------------------------'
+   */
+[_BL] = KEYMAP(
+  F(0),    KC_1,    KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,   KC_0,   KC_MINS,  KC_EQL,  KC_BSPC, \
+  KC_TAB,  KC_Q,    KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,   KC_P,   KC_LBRC,  KC_RBRC, KC_BSLS, \
+  KC_CAPS, KC_A,    KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,   KC_SCLN,KC_QUOT,  KC_NO,   KC_ENT,  \
+  KC_LSFT, KC_NO,   KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM,KC_DOT, KC_SLSH,  KC_NO,   KC_RSFT, \
+  KC_LCTL, KC_LGUI, KC_LALT,                KC_SPC,                                 KC_RALT,KC_RGUI, MO(_FL), KC_RCTL),
+
+  /* Keymap _FL: Function Layer
+   * ,-----------------------------------------------------------.
+   * |~ |F1 |F2 |F3 |F4 |F5 |F6 |F7 |F8 |F9 |F10|F11|F12|   DEL  |
+   * |-----------------------------------------------------------|
+   * |     |   |UP |   |   |   |   |   |   |   |   |BL-|BL+|BL   |
+   * |-----------------------------------------------------------|
+   * |       |LFT|DWN|RGT|   |   |   |   |   |   |   |           |
+   * |-----------------------------------------------------------|
+   * |        |FN1|FN2|FN3|FN4|FN5|FN6|FN7|FN8|   |   |          |
+   * |-----------------------------------------------------------|
+   * |    |    |    |                        |    |    |    |RSET|
+   * `-----------------------------------------------------------'
+   */
+[_FL] = KEYMAP(
+  #ifdef RGBLIGHT_ENABLE
+  KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  \
+  KC_TRNS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC,  BL_INC,  BL_TOGG, \
+  KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS, KC_TRNS, RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,                                     KC_TRNS, KC_TRNS, KC_TRNS, RESET),
+  #else
+  KC_GRV,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  KC_DEL,  \
+  KC_TRNS, KC_TRNS, KC_UP,   KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC,  BL_INC,  BL_TOGG, \
+  KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+  KC_TRNS, KC_TRNS, KC_TRNS,                   KC_TRNS,                                     KC_TRNS, KC_TRNS, KC_TRNS, RESET),
+  #endif
+};
+
+enum function_id {
+    SHIFT_ESC,
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+  [0]  = ACTION_FUNCTION(SHIFT_ESC),
+};
+
+void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  static uint8_t shift_esc_shift_mask;
+  switch (id) {
+    case SHIFT_ESC:
+      shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
+      if (record->event.pressed) {
+        if (shift_esc_shift_mask) {
+          add_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          add_key(KC_ESC);
+          send_keyboard_report();
+        }
+      } else {
+        if (shift_esc_shift_mask) {
+          del_key(KC_GRV);
+          send_keyboard_report();
+        } else {
+          del_key(KC_ESC);
+          send_keyboard_report();
+        }
+      }
+      break;
+  }
+}
diff --git a/keyboards/kc60/keymaps/ws2812/readme.md b/keyboards/kc60/keymaps/ws2812/readme.md
new file mode 100644
index 000000000..5588fd2d9
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/readme.md
@@ -0,0 +1,21 @@
+KC60 with WS2812 RGB Underglow
+======================
+
+![Image of KC60 with RGB Underglow](ws2812_example.jpg)
+
+## Quantum MK Firmware
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## WS2812 Support
+By default, it is now setup for 16 LEDs on the PF5 breakout pin. See [included image](ws2812_wiring.jpg) for wiring reference.
+
+### Build
+To build this keymap with WS2812 enabled, simply run `make KEYMAP=ws2812`.
+
+### Reference Images
+![Wiring Reference](ws2812_wiring.jpg)
+![RGB Strip turned on](ws2812_underside-lit.jpg)
+![RGB Strip turned off](ws2812_underside.jpg)
+
+### Additional Credits
+Keymap based on work by [TerryMatthews](https://github.com/TerryMathews) for GH60 Satan.
diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg
new file mode 100644
index 000000000..5c62cfded
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg
diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg
new file mode 100644
index 000000000..2eab21433
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg
diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg
new file mode 100644
index 000000000..159d63904
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg
diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg
new file mode 100644
index 000000000..61b749b66
--- /dev/null
+++ b/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg
diff --git a/keyboards/kc60/readme.md b/keyboards/kc60/readme.md
new file mode 100644
index 000000000..acc0df68d
--- /dev/null
+++ b/keyboards/kc60/readme.md
@@ -0,0 +1,27 @@
+KC60 (version 2.0) keyboard firmware
+======================
+
+## Quantum MK Firmware
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Building
+Download or clone the whole firmware and navigate to the keyboards/kc60 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
+
+## WS2812 Support
+![Image of KC60 with RGB Underglow](keymaps/ws2812/ws2812_example.jpg)
+
+Build with WS2812 Support by running `make KEYMAP=ws2812`.