Add MxSS keyboard (#3335)

* Added basic MxSS support

* Fixed split RSHFT for ISO layouts

* Updated readme.md for MxSS

* Added initial support for individual control of front RGB LEDs

* Changed RGBLED color selection to work using hue and saturation rather than RGB
Added code for LED state change on layer change

* Avoid needing an entire 8 bits to store the brightness value

* Added custom keycodes, along with their handlers

* Added EEPROM storage for front LED config

* Fixed up ability to use QMK Configurator and updated readme.md

* Applied suggested changes from pull request: https://github.com/standard/standard/issues/452

Updated name in license descriptions
Updated layouts to snake case
Corrected mistakes in info.json
Updated layer_colors to a weak attributed array in mxss.c

* Defined a new safe range for custom keycodes in keymap.c

1 files changed, 75 insertions, 0 deletions

diff --git a/keyboards/mxss/rules.mk b/keyboards/mxss/rules.mk
new file mode 100644
index 000000000..f46ae6374
--- /dev/null
+++ b/keyboards/mxss/rules.mk
@@ -0,0 +1,75 @@
+# MCU name
+#MCU = at90usb1286
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = no            # USB Nkey Rollover
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+
+# Remove the common RGB light code and use my iteration instead
+OPT_DEFS += -DRGBLIGHT_ENABLE
+SRC += rgblight.c
+SRC += ws2812.c
+CIE1931_CURVE = yes
+LED_BREATHING_TABLE = yes