Merge branch 'master' of https://github.com/jackhumbert/qmk_firmware

56 files changed, 870 insertions, 377 deletions

diff --git a/keyboards/alps64/matrix.c b/keyboards/alps64/matrix.c
index 805999d4a..b3508850d 100644
--- a/keyboards/alps64/matrix.c
+++ b/keyboards/alps64/matrix.c
@@ -100,6 +100,8 @@ uint8_t matrix_scan(void)
         }
     }
 
+    matrix_scan_quantum();
+
     return 1;
 }
 
diff --git a/keyboards/clueboard/Makefile b/keyboards/clueboard/Makefile
new file mode 100644
index 000000000..ccc01ea9a
--- /dev/null
+++ b/keyboards/clueboard/Makefile
@@ -0,0 +1,109 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+SUBPROJECT_DEFAULT = rev2
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+AUDIO_ENABLE ?= no
+RGBLIGHT_ENABLE ?= no   # Enable keyboard underlight functionality
+MIDI_ENABLE ?= no 		# MIDI controls
+UNICODE_ENABLE ?= no 		# Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
diff --git a/keyboards/clueboard1/clueboard1.c b/keyboards/clueboard/clueboard.c
index 5785f447f..13195bda6 100644
--- a/keyboards/clueboard1/clueboard1.c
+++ b/keyboards/clueboard/clueboard.c
@@ -1,4 +1,9 @@
-#include "clueboard1.h"
+#include "clueboard.h"
+
+void led_init_ports() {
+    // * Set our LED pins as output
+    DDRB |= (1<<4);
+}
 
 void led_set_kb(uint8_t usb_led) {
     DDRF |= (1<<0);
diff --git a/keyboards/clueboard/clueboard.h b/keyboards/clueboard/clueboard.h
new file mode 100644
index 000000000..4f2a3c1df
--- /dev/null
+++ b/keyboards/clueboard/clueboard.h
@@ -0,0 +1,13 @@
+#ifndef CLUEBOARD_H
+#define CLUEBOARD_H
+
+#ifdef SUBPROJECT_rev1
+    #include "rev1.h"
+#endif
+#ifdef SUBPROJECT_rev2
+    #include "rev2.h"
+#endif
+
+#include "quantum.h"
+
+#endif
diff --git a/keyboards/clueboard1/config.h b/keyboards/clueboard/config.h
index 16338ddb0..ceac80795 100644
--- a/keyboards/clueboard1/config.h
+++ b/keyboards/clueboard/config.h
@@ -22,29 +22,10 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0xC1ED
-#define PRODUCT_ID      0x2301
-#define DEVICE_VER      0x0003
 #define MANUFACTURER    Clueboard
 #define PRODUCT         Clueboard
 #define DESCRIPTION     QMK keyboard firmware for Clueboard
 
-/* key matrix size */
-#define MATRIX_ROWS 5
-#define MATRIX_COLS 16
-
-// ROWS: Top to bottom, COLS: Left to right
-/* Column pin configuration
-* col: 0  1  2  3  4  5  6  7  8  9  10 11 12 13 14 15
-* pin: B3 F1 F4 F5 F6 C7 C6 B6 B5 B4 D7 D6 D4 F7 B0 B1
-*/
-#define MATRIX_COL_PINS { B3, F1, F4, F5, F6, C7, C6, B6, B5, B4, D7, D6, D4, F7, B0, B1 }
-/* Row pin configuration
-* row: 0  1  2  3  4
-* pin: D1 D0 D2 D5 D3
-*/
-#define MATRIX_ROW_PINS { D1, D0, D2, D5, D3 }
-#define UNUSED_PINS
-
 /* COL2ROW or ROW2COL */
 #define DIODE_DIRECTION COL2ROW
 
@@ -64,16 +45,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
     keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
 )
 
-/* Underlight configuration
- */
- #define ws2812_PORTREG PORTB
- #define ws2812_DDRREG DDRB
- #define ws2812_pin 2
- #define RGBLED_NUM 14     // Number of LEDs
- #define RGBLIGHT_HUE_STEP 10
- #define RGBLIGHT_SAT_STEP 17
- #define RGBLIGHT_VAL_STEP 17
-
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.
@@ -92,4 +63,12 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
 
+
+#ifdef SUBPROJECT_rev1
+    #include "rev1/config.h"
+#endif
+#ifdef SUBPROJECT_rev2
+    #include "rev2/config.h"
+#endif
+
 #endif
diff --git a/keyboards/clueboard2/keymaps/default/keymap.c b/keyboards/clueboard/keymaps/default/keymap.c
index 1795e68cd..89f71e83a 100644
--- a/keyboards/clueboard2/keymaps/default/keymap.c
+++ b/keyboards/clueboard/keymaps/default/keymap.c
@@ -1,4 +1,4 @@
-#include "clueboard2.h"
+#include "clueboard.h"
 
 // Used for SHIFT_ESC
 #define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
@@ -138,6 +138,7 @@ void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
       if (record->event.pressed) {
         rgblight_toggle();
       }
+
       break;
     case RGBLED_INCREASE_HUE:
       if (record->event.pressed) {
diff --git a/keyboards/clueboard/keymaps/max/Makefile b/keyboards/clueboard/keymaps/max/Makefile
new file mode 100644
index 000000000..950dadf84
--- /dev/null
+++ b/keyboards/clueboard/keymaps/max/Makefile
@@ -0,0 +1,49 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging,
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Build Options
+#   change to "no" to disable the options, or define them in the makefile.mk in 
+#   the appropriate keymap folder that will get included automatically
+#
+RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/clueboard2/keymaps/max/keymap.c b/keyboards/clueboard/keymaps/max/keymap.c
index 65a101c2b..82c93401d 100644
--- a/keyboards/clueboard2/keymaps/max/keymap.c
+++ b/keyboards/clueboard/keymaps/max/keymap.c
@@ -1,4 +1,4 @@
-#include "clueboard2.h"
+#include "clueboard.h"
 
 // Used for SHIFT_ESC
 #define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
diff --git a/keyboards/clueboard2/keymaps/skully/keymap.c b/keyboards/clueboard/keymaps/skully/keymap.c
index 74a03f2f3..df6f054e0 100644
--- a/keyboards/clueboard2/keymaps/skully/keymap.c
+++ b/keyboards/clueboard/keymaps/skully/keymap.c
@@ -1,4 +1,4 @@
-#include "clueboard2.h"
+#include "clueboard.h"
 
 // Used for SHIFT_ESC
 #define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
diff --git a/keyboards/clueboard/rev1/Makefile b/keyboards/clueboard/rev1/Makefile
new file mode 100644
index 000000000..80a942d06
--- /dev/null
+++ b/keyboards/clueboard/rev1/Makefile
@@ -0,0 +1,5 @@
+BACKLIGHT_ENABLE = no
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
diff --git a/keyboards/clueboard/rev1/config.h b/keyboards/clueboard/rev1/config.h
new file mode 100644
index 000000000..9bb58f56e
--- /dev/null
+++ b/keyboards/clueboard/rev1/config.h
@@ -0,0 +1,37 @@
+#ifndef REV2_CONFIG_H
+#define REV2_CONFIG_H
+
+#include "../config.h"
+
+#define PRODUCT_ID      0x2301
+#define DEVICE_VER      0x0003
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 16
+
+// ROWS: Top to bottom, COLS: Left to right
+/* Column pin configuration
+* col: 0  1  2  3  4  5  6  7  8  9  10 11 12 13 14 15
+* pin: B3 F1 F4 F5 F6 C7 C6 B6 B5 B4 D7 D6 D4 F7 B0 B1
+*/
+#define MATRIX_COL_PINS { B3, F1, F4, F5, F6, C7, C6, B6, B5, B4, D7, D6, D4, F7, B0, B1 }
+/* Row pin configuration
+* row: 0  1  2  3  4
+* pin: D1 D0 D2 D5 D3
+*/
+#define MATRIX_ROW_PINS { D1, D0, D2, D5, D3 }
+#define UNUSED_PINS
+
+/* Underlight configuration
+ */
+#define ws2812_PORTREG PORTB
+#define ws2812_DDRREG DDRB
+#define ws2812_pin 2
+#define RGBLED_NUM 14     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+
+#endif
\ No newline at end of file
diff --git a/keyboards/clueboard/rev1/rev1.c b/keyboards/clueboard/rev1/rev1.c
new file mode 100644
index 000000000..520a869e5
--- /dev/null
+++ b/keyboards/clueboard/rev1/rev1.c
@@ -0,0 +1 @@
+#include "rev1.h"
diff --git a/keyboards/clueboard1/clueboard1.h b/keyboards/clueboard/rev1/rev1.h
index 3c6c33342..abdfd079b 100644
--- a/keyboards/clueboard1/clueboard1.h
+++ b/keyboards/clueboard/rev1/rev1.h
@@ -1,8 +1,7 @@
-#ifndef CLUEBOARD1_H
-#define CLUEBOARD1_H
-
-#include "quantum.h"
+#ifndef REV1_H
+#define REV1_H
 
+#include "../clueboard.h"
 
 /* Clueboard matrix layout
  * ,-----------------------------------------------------------.  ,---.
@@ -30,6 +29,7 @@
  */
 // The first section contains all of the arguements
 // The second converts the arguments into a two-dimensional array
+
 #define KEYMAP( \
     k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0A, k0B, k0C, k0D, k0E, k0F, \
     k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k1B, k1C, k1D,      k1F, \
diff --git a/keyboards/clueboard/rev2/Makefile b/keyboards/clueboard/rev2/Makefile
new file mode 100644
index 000000000..cea967b79
--- /dev/null
+++ b/keyboards/clueboard/rev2/Makefile
@@ -0,0 +1,5 @@
+BACKLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
diff --git a/keyboards/clueboard/rev2/config.h b/keyboards/clueboard/rev2/config.h
new file mode 100644
index 000000000..e2f8336be
--- /dev/null
+++ b/keyboards/clueboard/rev2/config.h
@@ -0,0 +1,40 @@
+#ifndef REV2_CONFIG_H
+#define REV2_CONFIG_H
+
+#include "../config.h"
+
+#define PRODUCT_ID      0x2320
+#define DEVICE_VER      0x0001
+
+/* key matrix size */
+#define MATRIX_ROWS 10
+#define MATRIX_COLS 8
+
+// ROWS: Top to bottom, COLS: Left to right
+/* Row pin configuration
+* row: 0  1  2  3  4  5  6  7  8  9
+* pin: B2 C7 C6 B6 B5 B0 B3 D5 D3 D2
+*/
+#define MATRIX_ROW_PINS { B2, C7, C6, B6, B5, B0, B3, D5, D3, D2 }
+/* Column pin configuration
+ * col: 0  1  2  3  4  5  6  7
+ * pin: F0 F1 F4 F5 F6 F7 E6 B1
+ */
+#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, E6, B1 }
+#define UNUSED_PINS
+
+ /* Backlight configuration
+ */
+#define BACKLIGHT_LEVELS 1
+
+/* Underlight configuration
+ */
+#define ws2812_PORTREG PORTD
+#define ws2812_DDRREG DDRD
+#define ws2812_pin 7
+#define RGBLED_NUM 14     // Number of LEDs
+#define RGBLIGHT_HUE_STEP 10
+#define RGBLIGHT_SAT_STEP 17
+#define RGBLIGHT_VAL_STEP 17
+
+#endif
\ No newline at end of file
diff --git a/keyboards/clueboard/rev2/rev2.c b/keyboards/clueboard/rev2/rev2.c
new file mode 100644
index 000000000..7a8ec368e
--- /dev/null
+++ b/keyboards/clueboard/rev2/rev2.c
@@ -0,0 +1,47 @@
+#include "rev2.h"
+#include <avr/io.h>
+#include "backlight.h"
+#include "print.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+	matrix_init_user();
+	led_init_ports();
+
+    // JTAG disable for PORT F. write JTD bit twice within four cycles.
+    MCUCR |= (1<<JTD);
+    MCUCR |= (1<<JTD);
+}
+
+
+void matrix_scan_kb(void) {
+    matrix_scan_user();
+}
+
+void backlight_init_ports(void) {
+    print("init_backlight_pin()\n");
+    // Set our LED pins as output
+    DDRD |= (1<<6); // Esc
+    DDRB |= (1<<7); // Page Up
+    DDRD |= (1<<4); // Arrows
+
+    // Set our LED pins low
+    PORTD &= ~(1<<6); // Esc
+    PORTB &= ~(1<<7); // Page Up
+    PORTD &= ~(1<<4); // Arrows
+}
+
+void backlight_set(uint8_t level) {
+    if ( level == 0 ) {
+        // Turn off light
+        PORTD |= (1<<6); // Esc
+        PORTB |= (1<<7); // Page Up
+        PORTD |= (1<<4); // Arrows
+    } else {
+        // Turn on light
+        PORTD &= ~(1<<6); // Esc
+        PORTB &= ~(1<<7); // Page Up
+        PORTD &= ~(1<<4); // Arrows
+    }
+}
diff --git a/keyboards/clueboard2/clueboard2.h b/keyboards/clueboard/rev2/rev2.h
index e474b3101..912de405d 100644
--- a/keyboards/clueboard2/clueboard2.h
+++ b/keyboards/clueboard/rev2/rev2.h
@@ -1,8 +1,7 @@
-#ifndef CLUEBOARD2_H
-#define CLUEBOARD2_H
-
-#include "quantum.h"
+#ifndef REV2_H
+#define REV2_H
 
+#include "../clueboard.h"
 
 /* Clueboard matrix layout
  * ,-----------------------------------------------------------.  ,---.
@@ -30,6 +29,7 @@
  */
 // The first section contains all of the arguments
 // The second converts the arguments into a two-dimensional array
+
 #define KEYMAP( \
     k00, k01, k02, k03, k04, k05, k06, k07, k50, k51, k52, k53, k54, k55, k56, k57, \
     k10, k11, k12, k13, k14, k15, k16, k17, k60, k61, k62, k63, k64, k65,      k67, \
diff --git a/keyboards/clueboard1/keymaps/default/keymap.c b/keyboards/clueboard1/keymaps/default/keymap.c
deleted file mode 100644
index 3f4f3c414..000000000
--- a/keyboards/clueboard1/keymaps/default/keymap.c
+++ /dev/null
@@ -1,184 +0,0 @@
-#include "clueboard1.h"
-
-#ifdef RGBLIGHT_ENABLE
-#include "rgblight.h"
-#endif
-
-// Used for SHIFT_ESC
-#define MODS_CTRL_MASK  (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
-
-// Each layer gets a name for readability, which is then used in the keymap matrix below.
-// The underscores don't mean anything - you can have a layer called STUFF or any other name.
-// Layer names don't all need to be of the same length, obviously, and you can also skip them
-// entirely and just use numbers.
-#define _BL 0
-#define _FL 1
-#define _RS 2
-
-const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-  /* Keymap _BL: (Base Layer) Default Layer
-   * ,--------------------------------------------------------------------------.  ,----.
-   * |Esc~|   1|   2|   3|   4|   5|   6|   7|   8|   9|   0|   -|   =|   \|  BS|  |PGUP|
-   * |--------------------------------------------------------------------------|  |----|
-   * |   Tab|   Q|   W|   E|   R|   T|   Y|   U|   I|   O|   P|   [|   ]|      \|  |PGDN|
-   * |--------------------------------------------------------------------------|  `----'
-   * |Capslck|   A|   S|   D|   F|   G|   H|   J|   K|   L|   ;|   '|   # |  Ent|
-   * |-----------------------------------------------------------------------------.
-   * |Shift|  BS|   Z|   X|   C|   V|   B|   N|   M|   ,|   .|   /|   BS|Shift|  UP|
-   * |------------------------------------------------------------------------|----|----.
-   * | Ctrl|  Gui|  Alt| MHen|    Space|    Space|  Hen|  Alt| Ctrl|  _FL|LEFT|DOWN|RGHT|
-   * `----------------------------------------------------------------------------------'
-   */
-[_BL] = KEYMAP(
-  F(0),    KC_1,    KC_2,   KC_3,   KC_4,   KC_5,   KC_6,   KC_7,   KC_8,   KC_9,    KC_0,     KC_MINS,  KC_EQL,   KC_GRV,  KC_BSPC,          KC_PGUP, \
-  KC_TAB,  KC_Q,    KC_W,   KC_E,   KC_R,   KC_T,   KC_Y,   KC_U,   KC_I,   KC_O,    KC_P,     KC_LBRC,  KC_RBRC,  KC_BSLS,                   KC_PGDN, \
-  KC_CAPS, KC_A,    KC_S,   KC_D,   KC_F,   KC_G,   KC_H,   KC_J,   KC_K,   KC_L,    KC_SCLN,  KC_QUOT,  KC_NUHS,  KC_ENT,                             \
-  KC_LSFT, KC_NUBS, KC_Z,   KC_X,   KC_C,   KC_V,   KC_B,   KC_N,   KC_M,   KC_COMM, KC_DOT,   KC_SLSH,  KC_RO,    KC_RSFT,          KC_UP,            \
-  KC_LCTL, KC_LGUI, KC_LALT, KC_MHEN,          KC_SPC,KC_SPC,                        KC_HENK,  KC_RALT,  KC_RCTL,  MO(_FL), KC_LEFT, KC_DOWN, KC_RGHT),
-
-  /* Keymap _FL: Function Layer
-   * ,--------------------------------------------------------------------------.  ,----.
-   * |   `|  F1|  F2|  F3|  F4|  F5|  F6|  F7|  F8|  F9| F10| F11| F12|    | Del|  |BLIN|
-   * |--------------------------------------------------------------------------|  |----|
-   * |      |    |    |    |    |    |    |    |PScr|SLck|Paus|    |    |       |  |BLDE|
-   * |--------------------------------------------------------------------------|  `----'
-   * |       |    | _RS|    |    |    |    |    |    |    |    |    |     |     |
-   * |-----------------------------------------------------------------------------.
-   * |     |    |    |    |    |    |    |    |    |    |    |    |     |     |PGUP|
-   * |------------------------------------------------------------------------|----|----.
-   * |     |     |     |     |         |         |     |     |     |  _FL|HOME|PGDN| END|
-   * `----------------------------------------------------------------------------------'
-   */
-[_FL] = KEYMAP(
-  KC_GRV,  KC_F1,   KC_F2,  KC_F3,  KC_F4,  KC_F5,  KC_F6,  KC_F7,  KC_F8,  KC_F9,   KC_F10,   KC_F11,   KC_F12,   KC_TRNS, KC_DEL,           BL_STEP, \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_PSCR,KC_SLCK, KC_PAUS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                   KC_TRNS, \
-  KC_TRNS, KC_TRNS, MO(_RS),KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                           \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,          KC_PGUP,         \
-  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,        KC_TRNS,KC_TRNS,                        KC_TRNS,  KC_TRNS,  KC_TRNS,  MO(_FL), KC_HOME, KC_PGDN, KC_END),
-
-  /* Keymap _RS: Reset layer
-   * ,--------------------------------------------------------------------------.  ,----.
-   * |    |    |    |    |    |    |    |    |    |    |    |    |    |    |    |  |    |
-   * |--------------------------------------------------------------------------|  |----|
-   * |      |    |    |    |RESET|   |    |    |    |    |    |    |    |       |  |    |
-   * |--------------------------------------------------------------------------|  `----'
-   * |       |    | _RS|    |    |    |    |    |    |    |    |    |     |     |
-   * |-----------------------------------------------------------------------------.
-   * |     |    |    |    |    |    |    |    |    |    |    |    |     |     |    |
-   * |------------------------------------------------------------------------|----|----.
-   * |     |     |     |     |         |         |     |     |     |  _FL|    |    |    |
-   * `----------------------------------------------------------------------------------'
-   */
-[_RS] = KEYMAP(
-  #ifdef RGBLIGHT_ENABLE
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, F(1),             F(7), \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,RESET,  KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                   F(8), \
-  KC_TRNS, KC_TRNS, MO(_RS),KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                         \
-  MO(_FL), KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  MO(_FL),          F(5),          \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,        F(2),   F(2),                            KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, F(4),    F(6),    F(3)),
-  #else
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS, KC_TRNS,          KC_TRNS, \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,RESET,  KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                   KC_TRNS, \
-  KC_TRNS, KC_TRNS, MO(_RS),KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,                            \
-  KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS,  KC_TRNS,  KC_TRNS,  KC_TRNS,          KC_TRNS,          \
-  KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS,        KC_TRNS,KC_TRNS,                        KC_TRNS,  KC_TRNS,  KC_TRNS,  MO(_FL), KC_TRNS, KC_TRNS, KC_TRNS),
-  #endif
-};
-
-enum function_id {
-    SHIFT_ESC,
-    #ifdef RGBLIGHT_ENABLE
-    RGBLED_TOGGLE,
-    RGBLED_STEP_MODE,
-    RGBLED_INCREASE_HUE,
-    RGBLED_DECREASE_HUE,
-    RGBLED_INCREASE_SAT,
-    RGBLED_DECREASE_SAT,
-    RGBLED_INCREASE_VAL,
-    RGBLED_DECREASE_VAL
-    #endif
-};
-
-const uint16_t PROGMEM fn_actions[] = {
-  [0]  = ACTION_FUNCTION(SHIFT_ESC),
-  #ifdef RGBLIGHT_ENABLE
-  [1]  = ACTION_FUNCTION(RGBLED_TOGGLE),
-  [2]  = ACTION_FUNCTION(RGBLED_STEP_MODE),
-  [3]  = ACTION_FUNCTION(RGBLED_INCREASE_HUE),
-  [4]  = ACTION_FUNCTION(RGBLED_DECREASE_HUE),
-  [5]  = ACTION_FUNCTION(RGBLED_INCREASE_SAT),
-  [6]  = ACTION_FUNCTION(RGBLED_DECREASE_SAT),
-  [7]  = ACTION_FUNCTION(RGBLED_INCREASE_VAL),
-  [8]  = ACTION_FUNCTION(RGBLED_DECREASE_VAL),
-  #endif
-};
-
-void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
-  static uint8_t shift_esc_shift_mask;
-  switch (id) {
-    case SHIFT_ESC:
-      shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
-      if (record->event.pressed) {
-        if (shift_esc_shift_mask) {
-          add_key(KC_GRV);
-          send_keyboard_report();
-        } else {
-          add_key(KC_ESC);
-          send_keyboard_report();
-        }
-      } else {
-        if (shift_esc_shift_mask) {
-          del_key(KC_GRV);
-          send_keyboard_report();
-        } else {
-          del_key(KC_ESC);
-          send_keyboard_report();
-        }
-      }
-      break;
-    //led operations
-    #ifdef RGBLIGHT_ENABLE
-    case RGBLED_TOGGLE:
-      if (record->event.pressed) {
-        rgblight_toggle();
-      }
-
-      break;
-    case RGBLED_INCREASE_HUE:
-      if (record->event.pressed) {
-        rgblight_increase_hue();
-      }
-      break;
-    case RGBLED_DECREASE_HUE:
-      if (record->event.pressed) {
-        rgblight_decrease_hue();
-      }
-      break;
-    case RGBLED_INCREASE_SAT:
-      if (record->event.pressed) {
-        rgblight_increase_sat();
-      }
-      break;
-    case RGBLED_DECREASE_SAT:
-      if (record->event.pressed) {
-        rgblight_decrease_sat();
-      }
-      break;
-    case RGBLED_INCREASE_VAL:
-      if (record->event.pressed) {
-        rgblight_increase_val();
-      }
-      break;
-    case RGBLED_DECREASE_VAL:
-      if (record->event.pressed) {
-        rgblight_decrease_val();
-      }
-      break;
-    case RGBLED_STEP_MODE:
-      if (record->event.pressed) {
-        rgblight_step();
-      }
-      break;
-    #endif
-  }
-}
diff --git a/keyboards/clueboard2/keymaps/max/Makefile b/keyboards/clueboard2/keymaps/max/Makefile
deleted file mode 100644
index 22b5b94e3..000000000
--- a/keyboards/clueboard2/keymaps/max/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
-
-ifndef QUANTUM_DIR
-	include ../../../../Makefile
-endif
\ No newline at end of file
diff --git a/keyboards/cluepad/Makefile b/keyboards/cluepad/Makefile
index eb7a58025..a331ff4dc 100644
--- a/keyboards/cluepad/Makefile
+++ b/keyboards/cluepad/Makefile
@@ -1,8 +1,4 @@
 
-
-# # project specific files
-SRC = backlight.c
-
 # MCU name
 #MCU = at90usb1287
 MCU = atmega32u4
diff --git a/keyboards/cluepad/backlight.c b/keyboards/cluepad/backlight.c
deleted file mode 100644
index a9caed1df..000000000
--- a/keyboards/cluepad/backlight.c
+++ /dev/null
@@ -1,54 +0,0 @@
-#include <avr/io.h>
-#include "backlight.h"
-#include "led.h"
-
-#include "print.h"
-
-int pwm_level;
-
-void led_set_kb(uint8_t usb_led)
-{
-    print("led_set\n");
-}
-
-void init_backlight_pin(void)
-{
-    // Set C7 to output
-    DDRC |= (1<<7);
-
-    // Initialize the timer
-    TC4H = 0x03;
-    OCR4C = 0xFF;
-    TCCR4A = 0b10000010;
-    TCCR4B = 0b00000001;
-}
-
-void backlight_set(uint8_t level)
-{
-    // Determine the PWM level
-    switch (level)
-    {
-        case 0:
-            // 33%
-            pwm_level = 0x54;
-            break;
-        case 1:
-            // 66%
-            pwm_level = 0xA8;
-            break;
-        case 2:
-            // 100%
-            pwm_level = 0xFF;
-            break;
-        case 3:
-            // 0%
-            pwm_level = 0x00;
-            break;
-        default:
-            xprintf("Unknown level: %d\n", level);
-    }
-
-    // Write the PWM level to the timer
-    TC4H = pwm_level >> 8;
-    OCR4A = 0xFF & pwm_level;
-}
diff --git a/keyboards/cluepad/cluepad.c b/keyboards/cluepad/cluepad.c
index cbbdccb30..1867b617f 100644
--- a/keyboards/cluepad/cluepad.c
+++ b/keyboards/cluepad/cluepad.c
@@ -1,15 +1,60 @@
 #include "cluepad.h"
 
+int pwm_level;
+
 void matrix_init_kb(void) {
     // put your keyboard start-up code here
     // runs once when the firmware starts up
     matrix_init_user();
 
-    #ifdef BACKLIGHT_ENABLE
-        init_backlight_pin();
-    #endif
-
     // JTAG disable for PORT F. write JTD bit twice within four cycles.
     MCUCR |= (1<<JTD);
     MCUCR |= (1<<JTD);
 };
+
+void led_set_kb(uint8_t usb_led)
+{
+    print("led_set\n");
+}
+
+void backlight_init_ports(void)
+{
+    // Set C7 to output
+    DDRC |= (1<<7);
+
+    // Initialize the timer
+    TC4H = 0x03;
+    OCR4C = 0xFF;
+    TCCR4A = 0b10000010;
+    TCCR4B = 0b00000001;
+}
+
+void backlight_set(uint8_t level)
+{
+    // Determine the PWM level
+    switch (level)
+    {
+        case 0:
+            // 33%
+            pwm_level = 0x54;
+            break;
+        case 1:
+            // 66%
+            pwm_level = 0xA8;
+            break;
+        case 2:
+            // 100%
+            pwm_level = 0xFF;
+            break;
+        case 3:
+            // 0%
+            pwm_level = 0x00;
+            break;
+        default:
+            xprintf("Unknown level: %d\n", level);
+    }
+
+    // Write the PWM level to the timer
+    TC4H = pwm_level >> 8;
+    OCR4A = 0xFF & pwm_level;
+}
diff --git a/keyboards/cluepad/cluepad.h b/keyboards/cluepad/cluepad.h
index 615a9111e..5e4a5999e 100644
--- a/keyboards/cluepad/cluepad.h
+++ b/keyboards/cluepad/cluepad.h
@@ -1,9 +1,7 @@
 #ifndef CLUEPAD_H
 #define CLUEPAD_H
 
-#include "matrix.h"
-#include "keymap.h"
-#include <stddef.h>
+#include "quantum.h"
 
 
 /* Cluepad matrix layout
diff --git a/keyboards/ergodox_ez/matrix.c b/keyboards/ergodox_ez/matrix.c
index e0de06c34..b87fddbad 100644
--- a/keyboards/ergodox_ez/matrix.c
+++ b/keyboards/ergodox_ez/matrix.c
@@ -187,8 +187,7 @@ uint8_t matrix_scan(void)
         }
     }
 
-
-    matrix_scan_kb();
+    matrix_scan_quantum();
 
     return 1;
 }
diff --git a/keyboards/handwired/Makefile b/keyboards/handwired/Makefile
new file mode 100644
index 000000000..57493a47c
--- /dev/null
+++ b/keyboards/handwired/Makefile
@@ -0,0 +1,3 @@
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/handwired/fivethirteen/Makefile b/keyboards/handwired/fivethirteen/Makefile
new file mode 100644
index 000000000..711759917
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/Makefile
@@ -0,0 +1,73 @@
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+
diff --git a/keyboards/handwired/fivethirteen/README.md b/keyboards/handwired/fivethirteen/README.md
new file mode 100644
index 000000000..b2e13cd6d
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/README.md
@@ -0,0 +1,28 @@
+fivethirteen keyboard firmware
+======================
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/handwired/fivethirteen folder.
+Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use
+the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+
+To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+
+```
+$ make keymap=[default|jack|<name>]
+```
+
+Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
diff --git a/keyboards/handwired/fivethirteen/config.h b/keyboards/handwired/fivethirteen/config.h
new file mode 100644
index 000000000..76596342b
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/config.h
@@ -0,0 +1,162 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6060
+#define DEVICE_VER      0x0001
+#define MANUFACTURER    rdg
+#define PRODUCT         fivethirteen
+#define DESCRIPTION     handwired 5x13 matrix keyboard
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 13
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F6, F7, B6, B5, B4 }
+#define MATRIX_COL_PINS { B0, B1, B2, B3, F0, D0, D1, D2, D3, C6, C7, D6, D7 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/handwired/fivethirteen/fivethirteen.c b/keyboards/handwired/fivethirteen/fivethirteen.c
new file mode 100644
index 000000000..4c16e72eb
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/fivethirteen.c
@@ -0,0 +1,8 @@
+#include "fivethirteen.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
diff --git a/keyboards/handwired/fivethirteen/fivethirteen.h b/keyboards/handwired/fivethirteen/fivethirteen.h
new file mode 100644
index 000000000..faa6de737
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/fivethirteen.h
@@ -0,0 +1,21 @@
+#ifndef FIVETHIRTEEN_H
+#define FIVETHIRTEEN_H
+
+#include "quantum.h"
+
+#define KEYMAP( \
+	k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k010, k011, k012, \
+	k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k110, k111, k112, \
+	k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k210, k211, k212, \
+	k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k310, k311, k312, \
+	k40, k41, k42, k43, k44,      k46, k47, k48, k49, k410, k411, k412  \
+) \
+{ \
+	{ k00, k01, k02, k03, k04, k05,   k06, k07, k08, k09, k010, k011, k012 }, \
+	{ k10, k11, k12, k13, k14, k15,   k16, k17, k18, k19, k110, k111, k112 }, \
+	{ k20, k21, k22, k23, k24, k25,   k26, k27, k28, k29, k210, k211, k212 }, \
+	{ k30, k31, k32, k33, k34, k35,   k36, k37, k38, k39, k310, k311, k312 }, \
+	{ k40, k41, k42, k43, k44, KC_NO, k46, k47, k48, k49, k410, k411, k412 }  \
+}
+
+#endif
diff --git a/keyboards/handwired/fivethirteen/keymaps/default/keymap.c b/keyboards/handwired/fivethirteen/keymaps/default/keymap.c
new file mode 100644
index 000000000..d718510d5
--- /dev/null
+++ b/keyboards/handwired/fivethirteen/keymaps/default/keymap.c
@@ -0,0 +1,49 @@
+#include "fivethirteen.h"
+
+#define _______ KC_TRNS
+
+#define HDN 1
+#define OSY 2
+#define MOS 3
+#define CTL_ESC CTL_T(KC_ESC)
+#define SFT_BSP SFT_T(KC_BSPC)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = KEYMAP(
+  KC_ESC,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_MINS, KC_EQL,  \
+  KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_LBRC, KC_RBRC, \
+  CTL_ESC, KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT, KC_ENT,  \
+  KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_UP,   KC_BSLS, \
+  MO(MOS), KC_LCTL, KC_LALT, KC_LGUI, MO(HDN),    KC_SPC    ,    SFT_BSP, MO(OSY), MO(HDN), KC_LEFT, KC_DOWN, KC_RGHT  \
+),
+[HDN] = KEYMAP(
+  _______,  KC_F1,  KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_F11,  KC_F12,  \
+  _______, KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, _______, _______, \
+  _______, KC_TILD, KC_GRV,  KC_BSLS, KC_PIPE, KC_MINS, KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT, KC_TILD, KC_GRV,  _______, \
+  _______, _______, _______, _______, _______, _______, _______, KC_ENT,  _______, _______, _______, KC_PGUP, _______, \
+  _______, _______, _______, _______, _______,      KC_UNDS    , KC_DEL,  _______, _______, KC_HOME, KC_PGDN, KC_END   \
+),
+[OSY] = KEYMAP(
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+  _______, KC_VOLD, KC_VOLU, KC_MUTE, KC_PWR,  _______, _______, _______, _______, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______,      _______,     _______, _______, _______, _______, _______, _______  \
+),
+[MOS] = KEYMAP(
+  _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______, _______, _______, KC_BTN1, KC_BTN2, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______, _______, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, _______, _______, _______, \
+  _______, _______, _______, _______, _______, _______, _______, KC_WH_D, KC_WH_U, _______, _______, _______, _______, \
+  _______, _______, _______, _______, _______,      _______,     _______, _______, _______, _______, _______, _______  \
+)
+};
+
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) {
+  return MACRO_NONE;
+};
diff --git a/keyboards/handwired/handwired.c b/keyboards/handwired/handwired.c
new file mode 100644
index 000000000..feef8a919
--- /dev/null
+++ b/keyboards/handwired/handwired.c
@@ -0,0 +1 @@
+#include "handwired.h"
\ No newline at end of file
diff --git a/keyboards/handwired/handwired.h b/keyboards/handwired/handwired.h
new file mode 100644
index 000000000..7a4a4835e
--- /dev/null
+++ b/keyboards/handwired/handwired.h
@@ -0,0 +1 @@
+#include "quantum.h"
\ No newline at end of file
diff --git a/keyboards/clueboard1/Makefile b/keyboards/handwired/onekey/Makefile
index a2599d214..c6d10856a 100644
--- a/keyboards/clueboard1/Makefile
+++ b/keyboards/handwired/onekey/Makefile
@@ -52,18 +52,14 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   comment out to disable the options.
 #
-BOOTMAGIC_ENABLE ?= yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+BOOTMAGIC_ENABLE ?= no	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes	# Mouse keys(+4700)
 EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
 CONSOLE_ENABLE ?= yes	# Console for debug(+400)
 COMMAND_ENABLE ?= yes    # Commands for debug and configuration
-NKRO_ENABLE ?= yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-AUDIO_ENABLE ?= no
-RGBLIGHT_ENABLE ?= no   # Enable keyboard underlight functionality
-MIDI_ENABLE ?= no 		# MIDI controls
-UNICODE_ENABLE ?= no 		# Unicode
-BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
 
 ifndef QUANTUM_DIR
-	include ../../Makefile
-endif
+	include ../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/clueboard2/config.h b/keyboards/handwired/onekey/config.h
index 2887519af..c0a6b5839 100644
--- a/keyboards/clueboard2/config.h
+++ b/keyboards/handwired/onekey/config.h
@@ -1,5 +1,5 @@
 /*
-Copyright 2012 Jun Wako <wakojun@gmail.com>
+Copyright 2015 Jun Wako <wakojun@gmail.com>
 
 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
@@ -21,38 +21,26 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #include "config_common.h"
 
 /* USB Device descriptor parameter */
-#define VENDOR_ID       0xC1ED
-#define PRODUCT_ID      0x2320
+#define VENDOR_ID       0xFEED
+#define PRODUCT_ID      0x6464
 #define DEVICE_VER      0x0001
-#define MANUFACTURER    Clueboard
-#define PRODUCT         Clueboard with RGB Underlighting
-#define DESCRIPTION     QMK keyboard firmware for Clueboard
+#define MANUFACTURER    none
+#define PRODUCT         onekey
+#define DESCRIPTION     test board for qmk
 
 /* key matrix size */
-#define MATRIX_ROWS 10
-#define MATRIX_COLS 8
+#define MATRIX_ROWS 1
+#define MATRIX_COLS 1
 
-// ROWS: Top to bottom, COLS: Left to right
-/* Row pin configuration
-* row: 0  1  2  3  4  5  6  7  8  9
-* pin: B2 C7 C6 B6 B5 B0 B3 D5 D3 D2
-*/
-#define MATRIX_ROW_PINS { B2, C7, C6, B6, B5, B0, B3, D5, D3, D2 }
-/* Column pin configuration
- * col: 0  1  2  3  4  5  6  7
- * pin: F0 F1 F4 F5 F6 F7 E6 B1
- */
-#define MATRIX_COL_PINS { F0, F1, F4, F5, F6, F7, E6, B1 }
+#define MATRIX_COL_PINS {  B0 }
+#define MATRIX_ROW_PINS {  D0 }
 #define UNUSED_PINS
 
-/* COL2ROW or ROW2COL */
-#define DIODE_DIRECTION COL2ROW
-
 /* define if matrix has ghost */
 //#define MATRIX_HAS_GHOST
 
 /* Set 0 if debouncing isn't needed */
-#define DEBOUNCING_DELAY 5
+#define DEBOUNCE    5
 
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
@@ -64,19 +52,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
     keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
 )
 
-/* Backlight configuration
- */
-#define BACKLIGHT_LEVELS 1
 
-/* Underlight configuration
- */
- #define ws2812_PORTREG PORTD
- #define ws2812_DDRREG DDRD
- #define ws2812_pin 7
- #define RGBLED_NUM 14     // Number of LEDs
- #define RGBLIGHT_HUE_STEP 10
- #define RGBLIGHT_SAT_STEP 17
- #define RGBLIGHT_VAL_STEP 17
 
 /*
  * Feature disable options
diff --git a/keyboards/handwired/onekey/keymaps/default/keymap.c b/keyboards/handwired/onekey/keymaps/default/keymap.c
new file mode 100644
index 000000000..756c4f51e
--- /dev/null
+++ b/keyboards/handwired/onekey/keymaps/default/keymap.c
@@ -0,0 +1,5 @@
+#include "onekey.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+    { KC_A }
+};
diff --git a/keyboards/handwired/onekey/onekey.c b/keyboards/handwired/onekey/onekey.c
new file mode 100644
index 000000000..c79e0120e
--- /dev/null
+++ b/keyboards/handwired/onekey/onekey.c
@@ -0,0 +1 @@
+#include "onekey.h"
\ No newline at end of file
diff --git a/keyboards/handwired/onekey/onekey.h b/keyboards/handwired/onekey/onekey.h
new file mode 100644
index 000000000..7a4a4835e
--- /dev/null
+++ b/keyboards/handwired/onekey/onekey.h
@@ -0,0 +1 @@
+#include "quantum.h"
\ No newline at end of file
diff --git a/keyboards/hhkb/matrix.c b/keyboards/hhkb/matrix.c
index 2dfb2f5e1..666b6f595 100644
--- a/keyboards/hhkb/matrix.c
+++ b/keyboards/hhkb/matrix.c
@@ -71,6 +71,14 @@ void matrix_init(void)
     matrix_prev = _matrix1;
 }
 
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+void matrix_scan_kb(void) {
+  matrix_scan_user();
+}
+
 uint8_t matrix_scan(void)
 {
     uint8_t *tmp;
@@ -150,6 +158,9 @@ uint8_t matrix_scan(void)
         KEY_POWER_OFF();
         suspend_power_down();
     }
+
+    matrix_scan_quantum();
+
     return 1;
 }
 
diff --git a/keyboards/planck/Makefile b/keyboards/planck/Makefile
index 08e9205cb..23944f92e 100644
--- a/keyboards/planck/Makefile
+++ b/keyboards/planck/Makefile
@@ -1,4 +1,5 @@
 
+SUBPROJECT_DEFAULT = rev4
 
 # MCU name
 #MCU = at90usb1287
diff --git a/keyboards/planck/config.h b/keyboards/planck/config.h
index da2b000f6..4dd1d22a9 100644
--- a/keyboards/planck/config.h
+++ b/keyboards/planck/config.h
@@ -23,7 +23,6 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 /* USB Device descriptor parameter */
 #define VENDOR_ID       0xFEED
 #define PRODUCT_ID      0x6060
-#define DEVICE_VER      0x0001
 #define MANUFACTURER    Ortholinear Keyboards
 #define PRODUCT         The Planck Keyboard
 #define DESCRIPTION     A compact ortholinear keyboard
@@ -79,4 +78,11 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 //#define NO_ACTION_MACRO
 //#define NO_ACTION_FUNCTION
 
+#ifdef SUBPROJECT_rev3
+    #include "rev3/config.h"
+#endif
+#ifdef SUBPROJECT_rev4
+    #include "rev4/config.h"
+#endif
+
 #endif
diff --git a/keyboards/planck/keymaps/experimental/config.h b/keyboards/planck/keymaps/experimental/config.h
index a9117e0ee..985e250ab 100644
--- a/keyboards/planck/keymaps/experimental/config.h
+++ b/keyboards/planck/keymaps/experimental/config.h
@@ -4,5 +4,6 @@
 #include "../../config.h"
 
 #define LEADER_TIMEOUT 300
+#define BACKLIGHT_BREATHING
 
 #endif
diff --git a/keyboards/planck/keymaps/experimental/keymap.c b/keyboards/planck/keymaps/experimental/keymap.c
index 041285684..8ec335d7d 100644
--- a/keyboards/planck/keymaps/experimental/keymap.c
+++ b/keyboards/planck/keymaps/experimental/keymap.c
@@ -23,15 +23,16 @@ extern keymap_config_t keymap_config;
 #define _PLOVER 5
 #define _ADJUST 16
 
-// Macro name shortcuts
-#define QWERTY M(_QWERTY)
-#define COLEMAK M(_COLEMAK)
-#define DVORAK M(_DVORAK)
-#define LOWER M(_LOWER)
-#define RAISE M(_RAISE)
-#define M_BL 5
-#define PLOVER M(12)
-#define EXT_PLV M(13)
+enum planck_keycodes {
+  QWERTY = SAFE_RANGE,
+  COLEMAK,
+  DVORAK,
+  PLOVER,
+  LOWER,
+  RAISE,
+  BACKLIT,
+  EXT_PLV
+};
 
 // Fillers to make layering more clear
 #define _______ KC_TRNS
@@ -54,7 +55,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC},
   {KC_ESC,  KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_QUOT},
   {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_ENT },
-  {M(M_BL), KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT}
+  {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT}
 },
 
 /* Colemak
@@ -90,7 +91,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
   {KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_BSPC},
   {KC_ESC,  KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_SLSH},
   {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_ENT },
-  {M(M_BL), KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT}
+  {KC_LEAD, KC_LCTL, KC_LALT, KC_LGUI, LOWER,   KC_SPC,  KC_SPC,  RAISE,   KC_LEFT, KC_DOWN, KC_UP,   KC_RGHT}
 },
 
 /* Lower
@@ -193,10 +194,10 @@ void persistant_default_layer_set(uint16_t default_layer) {
   default_layer_set(default_layer);
 }
 
-const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
-{
-      switch(id) {
-        case _QWERTY:
+
+bool process_record_user(uint16_t keycode, keyrecord_t *record) {
+  switch (keycode) {
+        case QWERTY:
           if (record->event.pressed) {
             #ifdef AUDIO_ENABLE
               PLAY_NOTE_ARRAY(tone_qwerty, false, 0);
@@ -204,7 +205,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             persistant_default_layer_set(1UL<<_QWERTY);
           }
           break;
-        case _COLEMAK:
+      return false;
+        case COLEMAK:
           if (record->event.pressed) {
             #ifdef AUDIO_ENABLE
               PLAY_NOTE_ARRAY(tone_colemak, false, 0);
@@ -212,7 +214,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             persistant_default_layer_set(1UL<<_COLEMAK);
           }
           break;
-        case _DVORAK:
+      return false;
+        case DVORAK:
           if (record->event.pressed) {
             #ifdef AUDIO_ENABLE
               PLAY_NOTE_ARRAY(tone_dvorak, false, 0);
@@ -220,7 +223,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             persistant_default_layer_set(1UL<<_DVORAK);
           }
           break;
-        case _LOWER:
+      return false;
+        case LOWER:
           if (record->event.pressed) {
             layer_on(_LOWER);
             #ifdef BACKLIGHT_ENABLE
@@ -233,7 +237,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             update_tri_layer(_LOWER, _RAISE, _ADJUST);
           }
           break;
-        case _RAISE:
+      return false;
+        case RAISE:
           if (record->event.pressed) {
             layer_on(_RAISE);
             #ifdef BACKLIGHT_ENABLE
@@ -246,7 +251,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             update_tri_layer(_LOWER, _RAISE, _ADJUST);
           }
           break;
-        case M_BL:
+      return false;
+        case BACKLIT:
           if (record->event.pressed) {
             register_code(KC_RSFT);
             #ifdef BACKLIGHT_ENABLE
@@ -256,7 +262,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             unregister_code(KC_RSFT);
           }
         break;
-        case 12:
+      return false;
+        case PLOVER:
           if (record->event.pressed) {
             #ifdef AUDIO_ENABLE
               stop_all_notes();
@@ -274,7 +281,8 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             eeconfig_update_keymap(keymap_config.raw);
           }
         break;
-        case 13:
+      return false;
+        case EXT_PLV:
           if (record->event.pressed) {
             #ifdef AUDIO_ENABLE
               PLAY_NOTE_ARRAY(tone_plover_gb, false, 0);
@@ -282,9 +290,10 @@ const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
             layer_off(_PLOVER);
           }
         break;
+      return false;
 
       }
-    return MACRO_NONE;
+  return true;
 };
 
 void matrix_init_user(void) {
@@ -326,6 +335,17 @@ void matrix_scan_user(void) {
     leading = false;
     leader_end(); 
 
+    SEQ_ONE_KEY (KC_R) {
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+      tap_random_base64();
+    }
     SEQ_ONE_KEY (KC_V) {
       SEND_STRING (QMK_KEYBOARD "/" QMK_KEYMAP " @ " QMK_VERSION);
     }
diff --git a/keyboards/planck/keymaps/yang/Makefile b/keyboards/planck/keymaps/yang/Makefile
index f4908d703..6b18762fa 100644
--- a/keyboards/planck/keymaps/yang/Makefile
+++ b/keyboards/planck/keymaps/yang/Makefile
@@ -3,6 +3,7 @@
 #   the appropriate keymap folder that will get included automatically
 #
 RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+AUDIO_ENABLE = no
 
 ifndef QUANTUM_DIR
 	include ../../../../Makefile
diff --git a/keyboards/planck/planck.h b/keyboards/planck/planck.h
index 81c0e8cb4..8cfee5d1c 100644
--- a/keyboards/planck/planck.h
+++ b/keyboards/planck/planck.h
@@ -1,6 +1,13 @@
 #ifndef PLANCK_H
 #define PLANCK_H
 
+#ifdef SUBPROJECT_rev3
+    #include "rev3.h"
+#endif
+#ifdef SUBPROJECT_rev4
+    #include "rev4.h"
+#endif
+
 #include "quantum.h"
 
 #define PLANCK_MIT( \
diff --git a/keyboards/planck/rev3/Makefile b/keyboards/planck/rev3/Makefile
new file mode 100644
index 000000000..3ed1445e4
--- /dev/null
+++ b/keyboards/planck/rev3/Makefile
@@ -0,0 +1,5 @@
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/planck/rev3/config.h b/keyboards/planck/rev3/config.h
new file mode 100644
index 000000000..cc37874e8
--- /dev/null
+++ b/keyboards/planck/rev3/config.h
@@ -0,0 +1,8 @@
+#ifndef REV3_CONFIG_H
+#define REV3_CONFIG_H
+
+#include "../config.h"
+
+#define DEVICE_VER 0x0003
+
+#endif
diff --git a/keyboards/planck/rev3/rev3.c b/keyboards/planck/rev3/rev3.c
new file mode 100644
index 000000000..9ccd1d880
--- /dev/null
+++ b/keyboards/planck/rev3/rev3.c
@@ -0,0 +1 @@
+#include "rev3.h"
\ No newline at end of file
diff --git a/keyboards/planck/rev3/rev3.h b/keyboards/planck/rev3/rev3.h
new file mode 100644
index 000000000..628951d97
--- /dev/null
+++ b/keyboards/planck/rev3/rev3.h
@@ -0,0 +1,6 @@
+#ifndef REV3_H
+#define REV3_H
+
+#include "../planck.h"
+
+#endif
\ No newline at end of file
diff --git a/keyboards/planck/rev4/Makefile b/keyboards/planck/rev4/Makefile
new file mode 100644
index 000000000..ed09f85a4
--- /dev/null
+++ b/keyboards/planck/rev4/Makefile
@@ -0,0 +1,5 @@
+AUDIO_ENABLE ?= yes           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/planck/rev4/config.h b/keyboards/planck/rev4/config.h
new file mode 100644
index 000000000..98189fba7
--- /dev/null
+++ b/keyboards/planck/rev4/config.h
@@ -0,0 +1,8 @@
+#ifndef REV4_CONFIG_H
+#define REV4_CONFIG_H
+
+#include "../config.h"
+
+#define DEVICE_VER 0x0004
+
+#endif
\ No newline at end of file
diff --git a/keyboards/planck/rev4/rev4.c b/keyboards/planck/rev4/rev4.c
new file mode 100644
index 000000000..98a75d2ed
--- /dev/null
+++ b/keyboards/planck/rev4/rev4.c
@@ -0,0 +1 @@
+#include "rev4.h"
\ No newline at end of file
diff --git a/keyboards/planck/rev4/rev4.h b/keyboards/planck/rev4/rev4.h
new file mode 100644
index 000000000..e4cf1800b
--- /dev/null
+++ b/keyboards/planck/rev4/rev4.h
@@ -0,0 +1,6 @@
+#ifndef REV4_H
+#define REV4_H
+
+#include "../planck.h"
+
+#endif
\ No newline at end of file
diff --git a/keyboards/readme.md b/keyboards/readme.md
index 5574619db..e97986546 100644
--- a/keyboards/readme.md
+++ b/keyboards/readme.md
@@ -23,8 +23,7 @@ Made in Taiwan using advanced robotic manufacturing, the ErgoDox EZ is a fully-a
 
 Designed and built in Felton, CA, Clueboards keyboard emphasize quality and locally sourced components, available on [clueboard.co](http://clueboard.co)
 
-* [Clueboard rev.1](/keyboards/clueboard1/) - The old Clueboard.
-* [Clueboard rev.2](/keyboards/clueboard2/) - New and improved! The Clueboard, revision 2.
+* [Clueboard](/keyboards/clueboard/) - The 66% custom keyboard.
 * [Cluepad](/keyboards/cluepad/) - A mechanical numpad with QMK superpowers.
 
 
diff --git a/keyboards/satan/satan.c b/keyboards/satan/satan.c
index 1c515f55f..d2c5d5c20 100644
--- a/keyboards/satan/satan.c
+++ b/keyboards/satan/satan.c
@@ -22,9 +22,9 @@ void led_init_ports(void) {
 void led_set_kb(uint8_t usb_led) {
     if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
         // Turn capslock on
-        PORTB |= (1<<2);
+        PORTB &= ~(1<<2);
     } else {
         // Turn capslock off
-        PORTB &= ~(1<<2);
+        PORTB |= (1<<2);
     }
 }
diff --git a/keyboards/sixkeyboard/matrix.c b/keyboards/sixkeyboard/matrix.c
index c27998648..ed1b70e28 100644
--- a/keyboards/sixkeyboard/matrix.c
+++ b/keyboards/sixkeyboard/matrix.c
@@ -87,7 +87,7 @@ uint8_t matrix_scan(void)
     matrix[0] = (PINC&(1<<7) ? 0 : (1<<0)) | (PINB&(1<<7) ? 0 : (1<<1)) | (PINB&(1<<5) ? 0 : (1<<2));
     matrix[1] = (PIND&(1<<6) ? 0 : (1<<0)) | (PIND&(1<<1) ? 0 : (1<<1)) | (PIND&(1<<4) ? 0 : (1<<2));
 
-    matrix_scan_kb();
+    matrix_scan_quantum();
 
     return 1;
 }