diff options
35 files changed, 2223 insertions, 0 deletions
diff --git a/drivers/issi/is31fl3736.c b/drivers/issi/is31fl3736.c new file mode 100644 index 000000000..c5d431097 --- /dev/null +++ b/drivers/issi/is31fl3736.c @@ -0,0 +1,306 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + + +#ifdef __AVR__ +#include <avr/interrupt.h> +#include <avr/io.h> +#include <util/delay.h> +#else +#include "wait.h" +#endif + +#include "is31fl3736.h" +#include <string.h> +#include "i2c_master.h" +#include "progmem.h" + + + +// This is a 7-bit address, that gets left-shifted and bit 0 +// set to 0 for write, 1 for read (as per I2C protocol) +// The address will vary depending on your wiring: +// 00 <-> GND +// 01 <-> SCL +// 10 <-> SDA +// 11 <-> VCC +// ADDR1 represents A1:A0 of the 7-bit address. +// ADDR2 represents A3:A2 of the 7-bit address. +// The result is: 0b101(ADDR2)(ADDR1) +#define ISSI_ADDR_DEFAULT 0x50 + +#define ISSI_COMMANDREGISTER 0xFD +#define ISSI_COMMANDREGISTER_WRITELOCK 0xFE +#define ISSI_INTERRUPTMASKREGISTER 0xF0 +#define ISSI_INTERRUPTSTATUSREGISTER 0xF1 + +#define ISSI_PAGE_LEDCONTROL 0x00 //PG0 +#define ISSI_PAGE_PWM 0x01 //PG1 +#define ISSI_PAGE_AUTOBREATH 0x02 //PG2 +#define ISSI_PAGE_FUNCTION 0x03 //PG3 + +#define ISSI_REG_CONFIGURATION 0x00 //PG3 +#define ISSI_REG_GLOBALCURRENT 0x01 //PG3 +#define ISSI_REG_RESET 0x11// PG3 +#define ISSI_REG_SWPULLUP 0x0F //PG3 +#define ISSI_REG_CSPULLUP 0x10 //PG3 + +#ifndef ISSI_TIMEOUT + #define ISSI_TIMEOUT 100 +#endif + +#ifndef ISSI_PERSISTENCE + #define ISSI_PERSISTENCE 0 +#endif + +// Transfer buffer for TWITransmitData() +uint8_t g_twi_transfer_buffer[20]; + +// These buffers match the IS31FL3736 PWM registers. +// The control buffers match the PG0 LED On/Off registers. +// Storing them like this is optimal for I2C transfers to the registers. +// We could optimize this and take out the unused registers from these +// buffers and the transfers in IS31FL3736_write_pwm_buffer() but it's +// probably not worth the extra complexity. +uint8_t g_pwm_buffer[DRIVER_COUNT][192]; +bool g_pwm_buffer_update_required = false; + +uint8_t g_led_control_registers[DRIVER_COUNT][24] = { { 0 }, { 0 } }; +bool g_led_control_registers_update_required = false; + +void IS31FL3736_write_register( uint8_t addr, uint8_t reg, uint8_t data ) +{ + g_twi_transfer_buffer[0] = reg; + g_twi_transfer_buffer[1] = data; + + #if ISSI_PERSISTENCE > 0 + for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) { + if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT) == 0) + break; + } + #else + i2c_transmit(addr << 1, g_twi_transfer_buffer, 2, ISSI_TIMEOUT); + #endif +} + +void IS31FL3736_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer ) +{ + // assumes PG1 is already selected + + // transmit PWM registers in 12 transfers of 16 bytes + // g_twi_transfer_buffer[] is 20 bytes + + // iterate over the pwm_buffer contents at 16 byte intervals + for ( int i = 0; i < 192; i += 16 ) { + g_twi_transfer_buffer[0] = i; + // copy the data from i to i+15 + // device will auto-increment register for data after the first byte + // thus this sets registers 0x00-0x0F, 0x10-0x1F, etc. in one transfer + for ( int j = 0; j < 16; j++ ) { + g_twi_transfer_buffer[1 + j] = pwm_buffer[i + j]; + } + + #if ISSI_PERSISTENCE > 0 + for (uint8_t i = 0; i < ISSI_PERSISTENCE; i++) { + if (i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT) == 0) + break; + } + #else + i2c_transmit(addr << 1, g_twi_transfer_buffer, 17, ISSI_TIMEOUT); + #endif + } +} + +void IS31FL3736_init( uint8_t addr ) +{ + // In order to avoid the LEDs being driven with garbage data + // in the LED driver's PWM registers, shutdown is enabled last. + // Set up the mode and other settings, clear the PWM registers, + // then disable software shutdown. + + // Unlock the command register. + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 ); + + // Select PG0 + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL ); + // Turn off all LEDs. + for ( int i = 0x00; i <= 0x17; i++ ) + { + IS31FL3736_write_register( addr, i, 0x00 ); + } + + // Unlock the command register. + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 ); + + // Select PG1 + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM ); + // Set PWM on all LEDs to 0 + // No need to setup Breath registers to PWM as that is the default. + for ( int i = 0x00; i <= 0xBF; i++ ) + { + IS31FL3736_write_register( addr, i, 0x00 ); + } + + // Unlock the command register. + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 ); + + // Select PG3 + IS31FL3736_write_register( addr, ISSI_COMMANDREGISTER, ISSI_PAGE_FUNCTION ); + // Set global current to maximum. + IS31FL3736_write_register( addr, ISSI_REG_GLOBALCURRENT, 0xFF ); + // Disable software shutdown. + IS31FL3736_write_register( addr, ISSI_REG_CONFIGURATION, 0x01 ); + + // Wait 10ms to ensure the device has woken up. + #ifdef __AVR__ + _delay_ms( 10 ); + #else + wait_ms(10); + #endif +} + +void IS31FL3736_set_color( int index, uint8_t red, uint8_t green, uint8_t blue ) +{ + if ( index >= 0 && index < DRIVER_LED_TOTAL ) { + is31_led led = g_is31_leds[index]; + + g_pwm_buffer[led.driver][led.r] = red; + g_pwm_buffer[led.driver][led.g] = green; + g_pwm_buffer[led.driver][led.b] = blue; + g_pwm_buffer_update_required = true; + } +} + +void IS31FL3736_set_color_all( uint8_t red, uint8_t green, uint8_t blue ) +{ + for ( int i = 0; i < DRIVER_LED_TOTAL; i++ ) + { + IS31FL3736_set_color( i, red, green, blue ); + } +} + +void IS31FL3736_set_led_control_register( uint8_t index, bool red, bool green, bool blue ) +{ + is31_led led = g_is31_leds[index]; + + // IS31FL3733 + // The PWM register for a matrix position (0x00 to 0xBF) can be + // divided by 8 to get the LED control register (0x00 to 0x17), + // then mod 8 to get the bit position within that register. + + // IS31FL3736 + // The PWM register for a matrix position (0x00 to 0xBF) is interleaved, so: + // A1=0x00 A2=0x02 A3=0x04 A4=0x06 A5=0x08 A6=0x0A A7=0x0C A8=0x0E + // B1=0x10 B2=0x12 B3=0x14 + // But also, the LED control registers (0x00 to 0x17) are also interleaved, so: + // A1-A4=0x00 A5-A8=0x01 + // So, the same math applies. + + uint8_t control_register_r = led.r / 8; + uint8_t control_register_g = led.g / 8; + uint8_t control_register_b = led.b / 8; + + uint8_t bit_r = led.r % 8; + uint8_t bit_g = led.g % 8; + uint8_t bit_b = led.b % 8; + + if ( red ) { + g_led_control_registers[led.driver][control_register_r] |= (1 << bit_r); + } else { + g_led_control_registers[led.driver][control_register_r] &= ~(1 << bit_r); + } + if ( green ) { + g_led_control_registers[led.driver][control_register_g] |= (1 << bit_g); + } else { + g_led_control_registers[led.driver][control_register_g] &= ~(1 << bit_g); + } + if ( blue ) { + g_led_control_registers[led.driver][control_register_b] |= (1 << bit_b); + } else { + g_led_control_registers[led.driver][control_register_b] &= ~(1 << bit_b); + } + + g_led_control_registers_update_required = true; + +} + +void IS31FL3736_mono_set_brightness( int index, uint8_t value ) +{ + if ( index >= 0 && index < 96 ) { + // Index in range 0..95 -> A1..A8, B1..B8, etc. + // Map index 0..95 to registers 0x00..0xBE (interleaved) + uint8_t pwm_register = index * 2; + g_pwm_buffer[0][pwm_register] = value; + g_pwm_buffer_update_required = true; + } +} + +void IS31FL3736_mono_set_brightness_all( uint8_t value ) +{ + for ( int i = 0; i < 96; i++ ) + { + IS31FL3736_mono_set_brightness( i, value ); + } +} + +void IS31FL3736_mono_set_led_control_register( uint8_t index, bool enabled ) +{ + // Index in range 0..95 -> A1..A8, B1..B8, etc. + + // Map index 0..95 to registers 0x00..0xBE (interleaved) + uint8_t pwm_register = index * 2; + // Map register 0x00..0xBE (interleaved) into control register and bit + uint8_t control_register = pwm_register / 8; + uint8_t bit = pwm_register % 8; + + if ( enabled ) { + g_led_control_registers[0][control_register] |= (1 << bit); + } else { + g_led_control_registers[0][control_register] &= ~(1 << bit); + } + + g_led_control_registers_update_required = true; +} + +void IS31FL3736_update_pwm_buffers( uint8_t addr1, uint8_t addr2 ) +{ + if ( g_pwm_buffer_update_required ) + { + // Firstly we need to unlock the command register and select PG1 + IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 ); + IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_PWM ); + + IS31FL3736_write_pwm_buffer( addr1, g_pwm_buffer[0] ); + //IS31FL3736_write_pwm_buffer( addr2, g_pwm_buffer[1] ); + } + g_pwm_buffer_update_required = false; +} + +void IS31FL3736_update_led_control_registers( uint8_t addr1, uint8_t addr2 ) +{ + if ( g_led_control_registers_update_required ) + { + // Firstly we need to unlock the command register and select PG0 + IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER_WRITELOCK, 0xC5 ); + IS31FL3736_write_register( addr1, ISSI_COMMANDREGISTER, ISSI_PAGE_LEDCONTROL ); + for ( int i=0; i<24; i++ ) + { + IS31FL3736_write_register(addr1, i, g_led_control_registers[0][i] ); + //IS31FL3736_write_register(addr2, i, g_led_control_registers[1][i] ); + } + } +} + diff --git a/drivers/issi/is31fl3736.h b/drivers/issi/is31fl3736.h new file mode 100644 index 000000000..cff50fd0d --- /dev/null +++ b/drivers/issi/is31fl3736.h @@ -0,0 +1,172 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include <stdint.h> +#include <stdbool.h> + + +// Simple interface option. +// If these aren't defined, just define them to make it compile + + +#ifndef DRIVER_COUNT +#define DRIVER_COUNT 2 +#endif + +#ifndef DRIVER_LED_TOTAL +#define DRIVER_LED_TOTAL 96 +#endif + + +typedef struct is31_led { + uint8_t driver:2; + uint8_t r; + uint8_t g; + uint8_t b; +} __attribute__((packed)) is31_led; + +extern const is31_led g_is31_leds[DRIVER_LED_TOTAL]; + +void IS31FL3736_init( uint8_t addr ); +void IS31FL3736_write_register( uint8_t addr, uint8_t reg, uint8_t data ); +void IS31FL3736_write_pwm_buffer( uint8_t addr, uint8_t *pwm_buffer ); + +void IS31FL3736_set_color( int index, uint8_t red, uint8_t green, uint8_t blue ); +void IS31FL3736_set_color_all( uint8_t red, uint8_t green, uint8_t blue ); + +void IS31FL3736_set_led_control_register( uint8_t index, bool red, bool green, bool blue ); + +void IS31FL3736_mono_set_brightness( int index, uint8_t value ); +void IS31FL3736_mono_set_brightness_all( uint8_t value ); +void IS31FL3736_mono_set_led_control_register( uint8_t index, bool enabled ); + +// This should not be called from an interrupt +// (eg. from a timer interrupt). +// Call this while idle (in between matrix scans). +// If the buffer is dirty, it will update the driver with the buffer. +void IS31FL3736_update_pwm_buffers( uint8_t addr1, uint8_t addr2 ); +void IS31FL3736_update_led_control_registers( uint8_t addr1, uint8_t addr2 ); + +#define A_1 0x00 +#define A_2 0x02 +#define A_3 0x04 +#define A_4 0x06 +#define A_5 0x08 +#define A_6 0x0A +#define A_7 0x0C +#define A_8 0x0E + +#define B_1 0x10 +#define B_2 0x12 +#define B_3 0x14 +#define B_4 0x16 +#define B_5 0x18 +#define B_6 0x1A +#define B_7 0x1C +#define B_8 0x1E + +#define C_1 0x20 +#define C_2 0x22 +#define C_3 0x24 +#define C_4 0x26 +#define C_5 0x28 +#define C_6 0x2A +#define C_7 0x2C +#define C_8 0x2E + +#define D_1 0x30 +#define D_2 0x32 +#define D_3 0x34 +#define D_4 0x36 +#define D_5 0x38 +#define D_6 0x3A +#define D_7 0x3C +#define D_8 0x3E + +#define E_1 0x40 +#define E_2 0x42 +#define E_3 0x44 +#define E_4 0x46 +#define E_5 0x48 +#define E_6 0x4A +#define E_7 0x4C +#define E_8 0x4E + +#define F_1 0x50 +#define F_2 0x52 +#define F_3 0x54 +#define F_4 0x56 +#define F_5 0x58 +#define F_6 0x5A +#define F_7 0x5C +#define F_8 0x5E + +#define G_1 0x60 +#define G_2 0x62 +#define G_3 0x64 +#define G_4 0x66 +#define G_5 0x68 +#define G_6 0x6A +#define G_7 0x6C +#define G_8 0x6E + +#define H_1 0x70 +#define H_2 0x72 +#define H_3 0x74 +#define H_4 0x76 +#define H_5 0x78 +#define H_6 0x7A +#define H_7 0x7C +#define H_8 0x7E + +#define I_1 0x80 +#define I_2 0x82 +#define I_3 0x84 +#define I_4 0x86 +#define I_5 0x88 +#define I_6 0x8A +#define I_7 0x8C +#define I_8 0x8E + +#define J_1 0x90 +#define J_2 0x92 +#define J_3 0x94 +#define J_4 0x96 +#define J_5 0x98 +#define J_6 0x9A +#define J_7 0x9C +#define J_8 0x9E + +#define K_1 0xA0 +#define K_2 0xA2 +#define K_3 0xA4 +#define K_4 0xA6 +#define K_5 0xA8 +#define K_6 0xAA +#define K_7 0xAC +#define K_8 0xAE + +#define L_1 0xB0 +#define L_2 0xB2 +#define L_3 0xB4 +#define L_4 0xB6 +#define L_5 0xB8 +#define L_6 0xBA +#define L_7 0xBC +#define L_8 0xBE + diff --git a/keyboards/rama/readme.md b/keyboards/rama/readme.md index 4625eb1ef..c7ddf6d11 100644 --- a/keyboards/rama/readme.md +++ b/keyboards/rama/readme.md @@ -6,4 +6,6 @@ Firmware for keyboards designed by [RAMA WORKS](https://rama.works) [RAMA M60-A](https://rama.works/#/m60-a/) +[RAMA U80-A](https://rama.works/#/tkl-a/) + [RAMA M10-B](https://www.massdrop.com/buy/rama-m10-a?mode=guest_open) diff --git a/keyboards/rama/u80_a/config.h b/keyboards/rama/u80_a/config.h new file mode 100644 index 000000000..bfd972828 --- /dev/null +++ b/keyboards/rama/u80_a/config.h @@ -0,0 +1,187 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x5241 // "RW" +#define PRODUCT_ID 0x080A // 80-A +#define DEVICE_VER 0x0001 +#define MANUFACTURER RAMA.WORKS +#define PRODUCT RAMA U80-A +#define DESCRIPTION RAMA U80-A Keyboard + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 17 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F1, F0, E6, F4, F6, F7 } +#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4, B7, B0 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION ROW2COL + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + diff --git a/keyboards/rama/u80_a/info.json b/keyboards/rama/u80_a/info.json new file mode 100644 index 000000000..cb61c89b8 --- /dev/null +++ b/keyboards/rama/u80_a/info.json @@ -0,0 +1,13 @@ +{ + "keyboard_name": "RAMA U80-A", + "url": "https://rama.works/#/tkl-a/", + "maintainer": "Wilba", + "bootloader": "atmel-dfu", + "width": 18.25, + "height": 6.5, + "layouts": { + "LAYOUT_all": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"label":"~", "x":0, "y":1.5}, {"label":"!", "x":1, "y":1.5}, {"label":"@", "x":2, "y":1.5}, {"label":"#", "x":3, "y":1.5}, {"label":"$", "x":4, "y":1.5}, {"label":"%", "x":5, "y":1.5}, {"label":"^", "x":6, "y":1.5}, {"label":"&", "x":7, "y":1.5}, {"label":"*", "x":8, "y":1.5}, {"label":"(", "x":9, "y":1.5}, {"label":")", "x":10, "y":1.5}, {"label":"_", "x":11, "y":1.5}, {"label":"+", "x":12, "y":1.5}, {"label":"Backspace", "x":13, "y":1.5}, {"x":14, "y":1.5}, {"label":"Insert", "x":15.25, "y":1.5}, {"label":"Home", "x":16.25, "y":1.5}, {"label":"PgUp", "x":17.25, "y":1.5}, {"label":"Tab", "x":0, "y":2.5, "w":1.5}, {"label":"Q", "x":1.5, "y":2.5}, {"label":"W", "x":2.5, "y":2.5}, {"label":"E", "x":3.5, "y":2.5}, {"label":"R", "x":4.5, "y":2.5}, {"label":"T", "x":5.5, "y":2.5}, {"label":"Y", "x":6.5, "y":2.5}, {"label":"U", "x":7.5, "y":2.5}, {"label":"I", "x":8.5, "y":2.5}, {"label":"O", "x":9.5, "y":2.5}, {"label":"P", "x":10.5, "y":2.5}, {"label":"{", "x":11.5, "y":2.5}, {"label":"}", "x":12.5, "y":2.5}, {"label":"|", "x":13.5, "y":2.5, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.5}, {"label":"End", "x":16.25, "y":2.5}, {"label":"PgDn", "x":17.25, "y":2.5}, {"label":"Caps Lock", "x":0, "y":3.5, "w":1.75}, {"label":"A", "x":1.75, "y":3.5}, {"label":"S", "x":2.75, "y":3.5}, {"label":"D", "x":3.75, "y":3.5}, {"label":"F", "x":4.75, "y":3.5}, {"label":"G", "x":5.75, "y":3.5}, {"label":"H", "x":6.75, "y":3.5}, {"label":"J", "x":7.75, "y":3.5}, {"label":"K", "x":8.75, "y":3.5}, {"label":"L", "x":9.75, "y":3.5}, {"label":":", "x":10.75, "y":3.5}, {"label":"\"", "x":11.75, "y":3.5}, {"label":"Enter", "x":12.75, "y":3.5, "w":2.25}, {"label":"Shift", "x":0, "y":4.5, "w":2.25}, {"label":"Z", "x":2.25, "y":4.5}, {"label":"X", "x":3.25, "y":4.5}, {"label":"C", "x":4.25, "y":4.5}, {"label":"V", "x":5.25, "y":4.5}, {"label":"B", "x":6.25, "y":4.5}, {"label":"N", "x":7.25, "y":4.5}, {"label":"M", "x":8.25, "y":4.5}, {"label":"<", "x":9.25, "y":4.5}, {"label":">", "x":10.25, "y":4.5}, {"label":"?", "x":11.25, "y":4.5}, {"label":"Shift", "x":12.25, "y":4.5, "w":1.75}, {"x":14, "y":4.5}, {"label":"\u2191", "x":16.25, "y":4.5}, {"label":"Ctrl", "x":0, "y":5.5, "w":1.25}, {"label":"Win", "x":1.25, "y":5.5, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"label":"Alt", "x":10, "y":5.5, "w":1.25}, {"label":"Win", "x":11.25, "y":5.5, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.5, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.5, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.5}, {"label":"\u2193", "x":16.25, "y":5.5}, {"label":"\u2192", "x":17.25, "y":5.5}] + } + } +} diff --git a/keyboards/rama/u80_a/keymaps/default/keymap.c b/keyboards/rama/u80_a/keymaps/default/keymap.c new file mode 100644 index 000000000..cf9225e3e --- /dev/null +++ b/keyboards/rama/u80_a/keymaps/default/keymap.c @@ -0,0 +1,22 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [0] = LAYOUT_all( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS, + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_TRNS, KC_UP, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_APP, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT), + + [1] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +}; + diff --git a/keyboards/rama/u80_a/readme.md b/keyboards/rama/u80_a/readme.md new file mode 100644 index 000000000..c98d00cb6 --- /dev/null +++ b/keyboards/rama/u80_a/readme.md @@ -0,0 +1,15 @@ +# RAMA U80-A + + + +A TKL keyboard. [More info at RAMA WORKS](https://rama.works/#/tkl-a/) + +Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582) +Hardware Supported: RAMA U80-A PCB +Hardware Availability: [RAMA WORKS Store](https://ramaworks.store/) + +Make example for this keyboard (after setting up your build environment): + + make rama/u80_a:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
\ No newline at end of file diff --git a/keyboards/rama/u80_a/rules.mk b/keyboards/rama/u80_a/rules.mk new file mode 100644 index 000000000..99224c247 --- /dev/null +++ b/keyboards/rama/u80_a/rules.mk @@ -0,0 +1,68 @@ +# project specific files +SRC = drivers/issi/is31fl3736.c \ + drivers/avr/i2c_master.c \ + keyboards/wilba_tech/wt_mono_backlight.c \ + keyboards/wilba_tech/wt_main.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section +BOOTLOADER = atmel-dfu + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches diff --git a/keyboards/rama/u80_a/u80_a.c b/keyboards/rama/u80_a/u80_a.c new file mode 100644 index 000000000..ccff6d62c --- /dev/null +++ b/keyboards/rama/u80_a/u80_a.c @@ -0,0 +1,17 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +// Nothing to see here, move along... ;-) diff --git a/keyboards/rama/u80_a/u80_a.h b/keyboards/rama/u80_a/u80_a.h new file mode 100644 index 000000000..26403ef34 --- /dev/null +++ b/keyboards/rama/u80_a/u80_a.h @@ -0,0 +1,43 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define ____ KC_NO + +// Right switch of split backspace is at 3,13 and is the only switch +// whose physical position doesn't match switch matrix position :-( +// However, it also makes no sense to view the physical as 18 columns, +// so the numbering goes 00 to 16. Deal with it. + +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, K015, K016, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K313, K114, K115, K116, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, \ + K400, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, K415, \ + K500, K501, K502, K506, K510, K511, K512, K513, K514, K515, K516 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, ____, K014, K015, K016 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, ____, ____, ____ }, \ + { K400, ____, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, ____, K415, ____ }, \ + { K500, K501, K502, ____, ____, ____, K506, ____, ____, ____, K510, K511, K512, K513, K514, K515, K516 } \ +} + diff --git a/keyboards/wilba_tech/wt60_a/config.h b/keyboards/wilba_tech/wt60_a/config.h new file mode 100644 index 000000000..95f4c786e --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/config.h @@ -0,0 +1,187 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x6582 // wilba.tech +#define PRODUCT_ID 0x060A // 60-A +#define DEVICE_VER 0x0001 +#define MANUFACTURER wilba.tech +#define PRODUCT wilba.tech WT60-A +#define DESCRIPTION wilba.tech WT60-A + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, E6, F4, F6, F7 } +#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION ROW2COL + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + diff --git a/keyboards/wilba_tech/wt60_a/info.json b/keyboards/wilba_tech/wt60_a/info.json new file mode 100644 index 000000000..3b3614a8b --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/info.json @@ -0,0 +1,16 @@ +{ + "keyboard_name": "wilba.tech WT60-A", + "url": "https://wilba.tech", + "maintainer": "Wilba", + "bootloader": "atmel-dfu", + "width": 15, + "height": 5, + "layouts": { + "LAYOUT_60_ansi": { + "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"Backspace", "x":13, "y":0, "w":2}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":2.75}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}] + }, + "LAYOUT_60_ansi_split_bs_rshift": { + "layout": [{"label":"~", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"|", "x":13.5, "y":1, "w":1.5}, {"label":"Caps Lock", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"x":14, "y":3}, {"label":"Ctrl", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"Menu", "x":12.5, "y":4, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":4, "w":1.25}] + } + } +}
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt60_a/keymaps/ansi_split_bs_rshift/keymap.c b/keyboards/wilba_tech/wt60_a/keymaps/ansi_split_bs_rshift/keymap.c new file mode 100644 index 000000000..95e01fc2c --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/keymaps/ansi_split_bs_rshift/keymap.c @@ -0,0 +1,38 @@ +// ANSI split backspace/right shift layout for WT60-A +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +// Default layer +[0] = LAYOUT_60_ansi_split_bs_rshift( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSLS, KC_DEL, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSPC, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, MO(1), + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_APP, KC_RCTL), + +// Fn1 Layer +[1] = LAYOUT_60_ansi_split_bs_rshift( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_INS, KC_DEL, + KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_UP, KC_TRNS, KC_TRNS, + KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_EJCT, KC_TRNS, KC_PAST, KC_PSLS, KC_HOME, KC_PGUP, KC_LEFT, KC_RGHT, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PPLS, KC_PMNS, KC_END, KC_PGDN, KC_DOWN, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +// Fn2 Layer +[2] = LAYOUT_60_ansi_split_bs_rshift( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +// Fn3 Layer +[3] = LAYOUT_60_ansi_split_bs_rshift( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +}; diff --git a/keyboards/wilba_tech/wt60_a/keymaps/default/keymap.c b/keyboards/wilba_tech/wt60_a/keymaps/default/keymap.c new file mode 100644 index 000000000..566736f5e --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/keymaps/default/keymap.c @@ -0,0 +1,38 @@ +// Default layout for WT60-A +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +// Default layer +[0] = LAYOUT_60_ansi( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, MO(1), KC_RCTL), + +// Fn1 Layer +[1] = LAYOUT_60_ansi( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL , + KC_CAPS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS, + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END, KC_PGDN, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +// Fn2 Layer +[2] = LAYOUT_60_ansi( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +// Fn3 Layer +[3] = LAYOUT_60_ansi( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +}; diff --git a/keyboards/wilba_tech/wt60_a/readme.md b/keyboards/wilba_tech/wt60_a/readme.md new file mode 100644 index 000000000..d7a73165d --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/readme.md @@ -0,0 +1,15 @@ +# WILBA.TECH WT60-A + + + +WT60-A is a keyboard PCB supporting 60% layout. [More info at wilba.tech](https://wilba.tech/) + +Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582) +Hardware Supported: WILBA.TECH WT65-A +Hardware Availability: Custom keyboard group buys + +Make example for this keyboard (after setting up your build environment): + + make wilba_tech/wt60_a:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt60_a/rules.mk b/keyboards/wilba_tech/wt60_a/rules.mk new file mode 100644 index 000000000..99224c247 --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/rules.mk @@ -0,0 +1,68 @@ +# project specific files +SRC = drivers/issi/is31fl3736.c \ + drivers/avr/i2c_master.c \ + keyboards/wilba_tech/wt_mono_backlight.c \ + keyboards/wilba_tech/wt_main.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section +BOOTLOADER = atmel-dfu + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches diff --git a/keyboards/wilba_tech/wt60_a/wt60_a.c b/keyboards/wilba_tech/wt60_a/wt60_a.c new file mode 100644 index 000000000..ccff6d62c --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/wt60_a.c @@ -0,0 +1,17 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +// Nothing to see here, move along... ;-) diff --git a/keyboards/wilba_tech/wt60_a/wt60_a.h b/keyboards/wilba_tech/wt60_a/wt60_a.h new file mode 100644 index 000000000..8ac8d9216 --- /dev/null +++ b/keyboards/wilba_tech/wt60_a/wt60_a.h @@ -0,0 +1,52 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define ____ KC_NO + +#define LAYOUT_60_ansi_split_bs_rshift( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K213, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, \ + K400, K401, K402, K406, K410, K411, K412, K413 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213 }, \ + { K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313 }, \ + { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413 } \ +} + +#define LAYOUT_60_ansi( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, \ + K400, K401, K402, K406, K410, K411, K412, K413 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, ____ }, \ + { K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, ____ }, \ + { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413 } \ +} + + + diff --git a/keyboards/wilba_tech/wt65_a/config.h b/keyboards/wilba_tech/wt65_a/config.h new file mode 100644 index 000000000..fa919f186 --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/config.h @@ -0,0 +1,187 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x6582 // wilba.tech +#define PRODUCT_ID 0x065A // 65-A +#define DEVICE_VER 0x0001 +#define MANUFACTURER wilba.tech +#define PRODUCT wilba.tech WT65-A +#define DESCRIPTION wilba.tech WT65-A + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F0, E6, F4, F6, F7 } +#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION ROW2COL + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + diff --git a/keyboards/wilba_tech/wt65_a/info.json b/keyboards/wilba_tech/wt65_a/info.json new file mode 100644 index 000000000..f2b18dadd --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/info.json @@ -0,0 +1,13 @@ +{ + "keyboard_name": "wilba.tech WT65-A", + "url": "https://wilba.tech", + "maintainer": "Wilba", + "bootloader": "atmel-dfu", + "width": 16, + "height": 5, + "layouts": { + "LAYOUT_all": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"!", "x":1, "y":0}, {"label":"@", "x":2, "y":0}, {"label":"#", "x":3, "y":0}, {"label":"$", "x":4, "y":0}, {"label":"%", "x":5, "y":0}, {"label":"^", "x":6, "y":0}, {"label":"&", "x":7, "y":0}, {"label":"*", "x":8, "y":0}, {"label":"(", "x":9, "y":0}, {"label":")", "x":10, "y":0}, {"label":"_", "x":11, "y":0}, {"label":"+", "x":12, "y":0}, {"label":"|", "x":13, "y":0}, {"label":"Del", "x":14, "y":0}, {"label":"Home", "x":15, "y":0}, {"label":"Tab", "x":0, "y":1, "w":1.5}, {"label":"Q", "x":1.5, "y":1}, {"label":"W", "x":2.5, "y":1}, {"label":"E", "x":3.5, "y":1}, {"label":"R", "x":4.5, "y":1}, {"label":"T", "x":5.5, "y":1}, {"label":"Y", "x":6.5, "y":1}, {"label":"U", "x":7.5, "y":1}, {"label":"I", "x":8.5, "y":1}, {"label":"O", "x":9.5, "y":1}, {"label":"P", "x":10.5, "y":1}, {"label":"{", "x":11.5, "y":1}, {"label":"}", "x":12.5, "y":1}, {"label":"Backspace", "x":13.5, "y":1, "w":1.5}, {"label":"PgUp", "x":15, "y":1}, {"label":"Control", "x":0, "y":2, "w":1.75}, {"label":"A", "x":1.75, "y":2}, {"label":"S", "x":2.75, "y":2}, {"label":"D", "x":3.75, "y":2}, {"label":"F", "x":4.75, "y":2}, {"label":"G", "x":5.75, "y":2}, {"label":"H", "x":6.75, "y":2}, {"label":"J", "x":7.75, "y":2}, {"label":"K", "x":8.75, "y":2}, {"label":"L", "x":9.75, "y":2}, {"label":":", "x":10.75, "y":2}, {"label":"\"", "x":11.75, "y":2}, {"label":"Enter", "x":12.75, "y":2, "w":2.25}, {"label":"PgDn", "x":15, "y":2}, {"label":"Shift", "x":0, "y":3, "w":2.25}, {"label":"Z", "x":2.25, "y":3}, {"label":"X", "x":3.25, "y":3}, {"label":"C", "x":4.25, "y":3}, {"label":"V", "x":5.25, "y":3}, {"label":"B", "x":6.25, "y":3}, {"label":"N", "x":7.25, "y":3}, {"label":"M", "x":8.25, "y":3}, {"label":"<", "x":9.25, "y":3}, {"label":">", "x":10.25, "y":3}, {"label":"?", "x":11.25, "y":3}, {"label":"Shift", "x":12.25, "y":3, "w":1.75}, {"label":"\u2191", "x":14, "y":3}, {"label":"End", "x":15, "y":3}, {"label":"Fn", "x":0, "y":4, "w":1.25}, {"label":"Win", "x":1.25, "y":4, "w":1.25}, {"label":"Alt", "x":2.5, "y":4, "w":1.25}, {"x":3.75, "y":4, "w":6.25}, {"label":"Alt", "x":10, "y":4, "w":1.25}, {"label":"Win", "x":11.25, "y":4, "w":1.25}, {"label":"\u2190", "x":13, "y":4}, {"label":"\u2193", "x":14, "y":4}, {"label":"\u2192", "x":15, "y":4}] + } + } +}
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt65_a/keymaps/default/keymap.c b/keyboards/wilba_tech/wt65_a/keymaps/default/keymap.c new file mode 100644 index 000000000..c5ae81168 --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/keymaps/default/keymap.c @@ -0,0 +1,37 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + // Default layer + [0] = LAYOUT_all( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_BSPC, KC_HOME, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_PGUP, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_PGDN, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_END, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, MO(1), KC_LEFT, KC_DOWN, KC_RGHT), + + // Fn1 Layer + [1] = LAYOUT_all( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, KC_DEL, KC_TRNS, + KC_CAPS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_INS, KC_TRNS, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_PGUP, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_VOLD, KC_VOLU, KC_MUTE, KC_END, KC_PGDN, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + + // Fn2 Layer + [2] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + + // Fn3 Layer + [3] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), +}; + diff --git a/keyboards/wilba_tech/wt65_a/readme.md b/keyboards/wilba_tech/wt65_a/readme.md new file mode 100644 index 000000000..1551b55b5 --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/readme.md @@ -0,0 +1,15 @@ +# WILBA.TECH WT65-A + + + +WT65-A is a keyboard PCB supporting 65% layout with 0.25U blocker. [More info at wilba.tech](https://wilba.tech/) + +Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582) +Hardware Supported: WILBA.TECH WT65-A +Hardware Availability: Custom keyboard group buys + +Make example for this keyboard (after setting up your build environment): + + make wilba_tech/wt65_a:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt65_a/rules.mk b/keyboards/wilba_tech/wt65_a/rules.mk new file mode 100644 index 000000000..99224c247 --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/rules.mk @@ -0,0 +1,68 @@ +# project specific files +SRC = drivers/issi/is31fl3736.c \ + drivers/avr/i2c_master.c \ + keyboards/wilba_tech/wt_mono_backlight.c \ + keyboards/wilba_tech/wt_main.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section +BOOTLOADER = atmel-dfu + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches diff --git a/keyboards/wilba_tech/wt65_a/wt65_a.c b/keyboards/wilba_tech/wt65_a/wt65_a.c new file mode 100644 index 000000000..ccff6d62c --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/wt65_a.c @@ -0,0 +1,17 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +// Nothing to see here, move along... ;-) diff --git a/keyboards/wilba_tech/wt65_a/wt65_a.h b/keyboards/wilba_tech/wt65_a/wt65_a.h new file mode 100644 index 000000000..9c3e6e12b --- /dev/null +++ b/keyboards/wilba_tech/wt65_a/wt65_a.h @@ -0,0 +1,41 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define ____ KC_NO + +// Right switch of split backspace is at 2,13 and is the only switch +// whose physical position doesn't match switch matrix position :-( +// However, it also makes no sense to view the physical as 16 columns, +// so the numbering goes 00 to 14. Deal with it. + +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K213, K014, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K214, \ + K300, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314, \ + K400, K401, K402, K406, K410, K411, K412, K413, K414 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K013, K014 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214 }, \ + { K300, ____, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, K314 }, \ + { K400, K401, K402, ____, ____, ____, K406, ____, ____, ____, K410, K411, K412, K413, K414 } \ +} + diff --git a/keyboards/wilba_tech/wt80_a/config.h b/keyboards/wilba_tech/wt80_a/config.h new file mode 100644 index 000000000..9687cb6d6 --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/config.h @@ -0,0 +1,187 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0x6582 // wilba.tech +#define PRODUCT_ID 0x080A // 80-A +#define DEVICE_VER 0x0001 +#define MANUFACTURER wilba.tech +#define PRODUCT wilba.tech WT80-A +#define DESCRIPTION wilba.tech WT80-A + +/* key matrix size */ +#define MATRIX_ROWS 6 +#define MATRIX_COLS 17 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +#define MATRIX_ROW_PINS { F1, F0, E6, F4, F6, F7 } +#define MATRIX_COL_PINS { F5, D5, B1, B2, B3, D3, D2, C7, C6, B6, B5, B4, D7, D6, D4, B7, B0 } +#define UNUSED_PINS + +/* COL2ROW, ROW2COL, or CUSTOM_MATRIX */ +#define DIODE_DIRECTION ROW2COL + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* If defined, GRAVE_ESC will always act as ESC when CTRL is held. + * This is userful for the Windows task manager shortcut (ctrl+shift+esc). + */ +// #define GRAVE_ESC_CTRL_OVERRIDE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +/* + * MIDI options + */ + +/* Prevent use of disabled MIDI features in the keymap */ +//#define MIDI_ENABLE_STRICT 1 + +/* enable basic MIDI features: + - MIDI notes can be sent when in Music mode is on +*/ +//#define MIDI_BASIC + +/* enable advanced MIDI features: + - MIDI notes can be added to the keymap + - Octave shift and transpose + - Virtual sustain, portamento, and modulation wheel + - etc. +*/ +//#define MIDI_ADVANCED + +/* override number of MIDI tone keycodes (each octave adds 12 keycodes and allocates 12 bytes) */ +//#define MIDI_TONE_KEYCODE_OCTAVES 1 + diff --git a/keyboards/wilba_tech/wt80_a/info.json b/keyboards/wilba_tech/wt80_a/info.json new file mode 100644 index 000000000..a43acb2f5 --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/info.json @@ -0,0 +1,13 @@ +{ + "keyboard_name": "wilba.tech WT80-A", + "url": "https://wilba.tech", + "maintainer": "Wilba", + "bootloader": "atmel-dfu", + "width": 18.25, + "height": 6.5, + "layouts": { + "LAYOUT_all": { + "layout": [{"label":"Esc", "x":0, "y":0}, {"label":"F1", "x":2, "y":0}, {"label":"F2", "x":3, "y":0}, {"label":"F3", "x":4, "y":0}, {"label":"F4", "x":5, "y":0}, {"label":"F5", "x":6.5, "y":0}, {"label":"F6", "x":7.5, "y":0}, {"label":"F7", "x":8.5, "y":0}, {"label":"F8", "x":9.5, "y":0}, {"label":"F9", "x":11, "y":0}, {"label":"F10", "x":12, "y":0}, {"label":"F11", "x":13, "y":0}, {"label":"F12", "x":14, "y":0}, {"label":"PrtSc", "x":15.25, "y":0}, {"label":"Scroll Lock", "x":16.25, "y":0}, {"label":"Pause", "x":17.25, "y":0}, {"label":"~", "x":0, "y":1.5}, {"label":"!", "x":1, "y":1.5}, {"label":"@", "x":2, "y":1.5}, {"label":"#", "x":3, "y":1.5}, {"label":"$", "x":4, "y":1.5}, {"label":"%", "x":5, "y":1.5}, {"label":"^", "x":6, "y":1.5}, {"label":"&", "x":7, "y":1.5}, {"label":"*", "x":8, "y":1.5}, {"label":"(", "x":9, "y":1.5}, {"label":")", "x":10, "y":1.5}, {"label":"_", "x":11, "y":1.5}, {"label":"+", "x":12, "y":1.5}, {"label":"Backspace", "x":13, "y":1.5}, {"x":14, "y":1.5}, {"label":"Insert", "x":15.25, "y":1.5}, {"label":"Home", "x":16.25, "y":1.5}, {"label":"PgUp", "x":17.25, "y":1.5}, {"label":"Tab", "x":0, "y":2.5, "w":1.5}, {"label":"Q", "x":1.5, "y":2.5}, {"label":"W", "x":2.5, "y":2.5}, {"label":"E", "x":3.5, "y":2.5}, {"label":"R", "x":4.5, "y":2.5}, {"label":"T", "x":5.5, "y":2.5}, {"label":"Y", "x":6.5, "y":2.5}, {"label":"U", "x":7.5, "y":2.5}, {"label":"I", "x":8.5, "y":2.5}, {"label":"O", "x":9.5, "y":2.5}, {"label":"P", "x":10.5, "y":2.5}, {"label":"{", "x":11.5, "y":2.5}, {"label":"}", "x":12.5, "y":2.5}, {"label":"|", "x":13.5, "y":2.5, "w":1.5}, {"label":"Delete", "x":15.25, "y":2.5}, {"label":"End", "x":16.25, "y":2.5}, {"label":"PgDn", "x":17.25, "y":2.5}, {"label":"Caps Lock", "x":0, "y":3.5, "w":1.75}, {"label":"A", "x":1.75, "y":3.5}, {"label":"S", "x":2.75, "y":3.5}, {"label":"D", "x":3.75, "y":3.5}, {"label":"F", "x":4.75, "y":3.5}, {"label":"G", "x":5.75, "y":3.5}, {"label":"H", "x":6.75, "y":3.5}, {"label":"J", "x":7.75, "y":3.5}, {"label":"K", "x":8.75, "y":3.5}, {"label":"L", "x":9.75, "y":3.5}, {"label":":", "x":10.75, "y":3.5}, {"label":"\"", "x":11.75, "y":3.5}, {"label":"Enter", "x":12.75, "y":3.5, "w":2.25}, {"label":"Shift", "x":0, "y":4.5, "w":2.25}, {"label":"Z", "x":2.25, "y":4.5}, {"label":"X", "x":3.25, "y":4.5}, {"label":"C", "x":4.25, "y":4.5}, {"label":"V", "x":5.25, "y":4.5}, {"label":"B", "x":6.25, "y":4.5}, {"label":"N", "x":7.25, "y":4.5}, {"label":"M", "x":8.25, "y":4.5}, {"label":"<", "x":9.25, "y":4.5}, {"label":">", "x":10.25, "y":4.5}, {"label":"?", "x":11.25, "y":4.5}, {"label":"Shift", "x":12.25, "y":4.5, "w":1.75}, {"x":14, "y":4.5}, {"label":"\u2191", "x":16.25, "y":4.5}, {"label":"Ctrl", "x":0, "y":5.5, "w":1.25}, {"label":"Win", "x":1.25, "y":5.5, "w":1.25}, {"label":"Alt", "x":2.5, "y":5.5, "w":1.25}, {"x":3.75, "y":5.5, "w":6.25}, {"label":"Alt", "x":10, "y":5.5, "w":1.25}, {"label":"Win", "x":11.25, "y":5.5, "w":1.25}, {"label":"Menu", "x":12.5, "y":5.5, "w":1.25}, {"label":"Ctrl", "x":13.75, "y":5.5, "w":1.25}, {"label":"\u2190", "x":15.25, "y":5.5}, {"label":"\u2193", "x":16.25, "y":5.5}, {"label":"\u2192", "x":17.25, "y":5.5}] + } + } +} diff --git a/keyboards/wilba_tech/wt80_a/keymaps/default/keymap.c b/keyboards/wilba_tech/wt80_a/keymaps/default/keymap.c new file mode 100644 index 000000000..cf9225e3e --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/keymaps/default/keymap.c @@ -0,0 +1,22 @@ +#include QMK_KEYBOARD_H + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + [0] = LAYOUT_all( + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_SLCK, KC_PAUS, + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_BSPC, KC_INS, KC_HOME, KC_PGUP, + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_DEL, KC_END, KC_PGDN, + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_TRNS, KC_UP, + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, KC_RGUI, KC_APP, KC_RCTL, KC_LEFT, KC_DOWN, KC_RGHT), + + [1] = LAYOUT_all( + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), + +}; + diff --git a/keyboards/wilba_tech/wt80_a/readme.md b/keyboards/wilba_tech/wt80_a/readme.md new file mode 100644 index 000000000..011805748 --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/readme.md @@ -0,0 +1,15 @@ +# WILBA.TECH WT80-A + + + +WT80-A is a keyboard PCB supporting TKL layout with 0.25U gaps. [More info at wilba.tech](https://wilba.tech/) + +Keyboard Maintainer: [Wilba6582](https://github.com/Wilba6582) +Hardware Supported: WILBA.TECH WT80-A +Hardware Availability: Custom keyboard group buys + +Make example for this keyboard (after setting up your build environment): + + make wilba_tech/wt80_a:default + +See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
\ No newline at end of file diff --git a/keyboards/wilba_tech/wt80_a/rules.mk b/keyboards/wilba_tech/wt80_a/rules.mk new file mode 100644 index 000000000..99224c247 --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/rules.mk @@ -0,0 +1,68 @@ +# project specific files +SRC = drivers/issi/is31fl3736.c \ + drivers/avr/i2c_master.c \ + keyboards/wilba_tech/wt_mono_backlight.c \ + keyboards/wilba_tech/wt_main.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section +BOOTLOADER = atmel-dfu + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE = no # USB Nkey Rollover +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE = no # Audio output on port C6 +FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches diff --git a/keyboards/wilba_tech/wt80_a/wt80_a.c b/keyboards/wilba_tech/wt80_a/wt80_a.c new file mode 100644 index 000000000..ccff6d62c --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/wt80_a.c @@ -0,0 +1,17 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +// Nothing to see here, move along... ;-) diff --git a/keyboards/wilba_tech/wt80_a/wt80_a.h b/keyboards/wilba_tech/wt80_a/wt80_a.h new file mode 100644 index 000000000..26403ef34 --- /dev/null +++ b/keyboards/wilba_tech/wt80_a/wt80_a.h @@ -0,0 +1,43 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include "quantum.h" + +#define ____ KC_NO + +// Right switch of split backspace is at 3,13 and is the only switch +// whose physical position doesn't match switch matrix position :-( +// However, it also makes no sense to view the physical as 18 columns, +// so the numbering goes 00 to 16. Deal with it. + +#define LAYOUT_all( \ + K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, K014, K015, K016, \ + K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K313, K114, K115, K116, \ + K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216, \ + K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, \ + K400, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, K415, \ + K500, K501, K502, K506, K510, K511, K512, K513, K514, K515, K516 \ +) { \ + { K000, K001, K002, K003, K004, K005, K006, K007, K008, K009, K010, K011, K012, ____, K014, K015, K016 }, \ + { K100, K101, K102, K103, K104, K105, K106, K107, K108, K109, K110, K111, K112, K113, K114, K115, K116 }, \ + { K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, K212, K213, K214, K215, K216 }, \ + { K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, ____, ____, ____ }, \ + { K400, ____, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, K413, ____, K415, ____ }, \ + { K500, K501, K502, ____, ____, ____, K506, ____, ____, ____, K510, K511, K512, K513, K514, K515, K516 } \ +} + diff --git a/keyboards/wilba_tech/wt_main.c b/keyboards/wilba_tech/wt_main.c new file mode 100644 index 000000000..f514dbefc --- /dev/null +++ b/keyboards/wilba_tech/wt_main.c @@ -0,0 +1,55 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "quantum.h" +#include "keyboards/wilba_tech/wt_mono_backlight.h" + +void bootmagic_lite(void) +{ + // The lite version of TMK's bootmagic. + // 100% less potential for accidentally making the + // keyboard do stupid things. + + // We need multiple scans because debouncing can't be turned off. + matrix_scan(); + wait_ms(DEBOUNCING_DELAY); + wait_ms(DEBOUNCING_DELAY); + matrix_scan(); + + // If the Esc (matrix 0,0) is held down on power up, + // reset the EEPROM valid state and jump to bootloader. + if ( matrix_get_row(0) & (1<<0) ) { + // Set the TMK/QMK EEPROM state as invalid. + eeconfig_disable(); + // Jump to bootloader. + bootloader_jump(); + } +} + +void matrix_init_kb(void) +{ + bootmagic_lite(); + backlight_init_drivers(); + backlight_timer_init(); + backlight_timer_enable(); + matrix_init_user(); +} + +void matrix_scan_kb(void) +{ + backlight_update_pwm_buffers(); + matrix_scan_user(); +} diff --git a/keyboards/wilba_tech/wt_mono_backlight.c b/keyboards/wilba_tech/wt_mono_backlight.c new file mode 100644 index 000000000..bf485bce1 --- /dev/null +++ b/keyboards/wilba_tech/wt_mono_backlight.c @@ -0,0 +1,116 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include "wt_mono_backlight.h" +#include "drivers/avr/i2c_master.h" +#include "drivers/issi/is31fl3736.h" + +#include <avr/interrupt.h> + +#define ISSI_ADDR_DEFAULT 0x50 + +bool g_suspend_state = false; + +// Global tick at 20 Hz +uint32_t g_tick = 0; +uint8_t g_config_effect_speed = 0; +uint8_t g_config_brightness = 255; + +void backlight_init_drivers(void) +{ + // Initialize I2C + i2c_init(); + IS31FL3736_init( ISSI_ADDR_DEFAULT ); + + for ( uint8_t index = 0; index < 96; index++ ) { + IS31FL3736_mono_set_led_control_register( index, true ); + } + IS31FL3736_update_led_control_registers( ISSI_ADDR_DEFAULT, 0x00 ); +} + + +// This is (F_CPU/1024) / 20 Hz +// = 15625 Hz / 20 Hz +// = 781 +#define TIMER3_TOP 781 + +void backlight_timer_init(void) +{ + static uint8_t backlight_timer_is_init = 0; + if ( backlight_timer_is_init ) { + return; + } + backlight_timer_is_init = 1; + + // Timer 3 setup + TCCR3B = _BV(WGM32) | // CTC mode OCR3A as TOP + _BV(CS32) | _BV(CS30); // prescale by /1024 + // Set TOP value + uint8_t sreg = SREG; + cli(); + + OCR3AH = (TIMER3_TOP >> 8) & 0xff; + OCR3AL = TIMER3_TOP & 0xff; + SREG = sreg; +} + +void backlight_timer_enable(void) +{ + TIMSK3 |= _BV(OCIE3A); +} + +void backlight_timer_disable(void) +{ + TIMSK3 &= ~_BV(OCIE3A); +} + +void backlight_set_suspend_state(bool state) +{ + g_suspend_state = state; +} + +void backlight_effect_cycle_all(void) +{ + uint8_t offset = ( g_tick << g_config_effect_speed ) & 0xFF; + + backlight_set_brightness_all( offset ); +} + +ISR(TIMER3_COMPA_vect) +{ + // delay 1 second before driving LEDs or doing anything else + static uint8_t startup_tick = 0; + if ( startup_tick < 20 ) { + startup_tick++; + return; + } + + g_tick++; + + //backlight_effect_cycle_all(); + backlight_set_brightness_all( 255 ); +} + +void backlight_update_pwm_buffers(void) +{ + IS31FL3736_update_pwm_buffers(ISSI_ADDR_DEFAULT,0x00); +} + +void backlight_set_brightness_all( uint8_t value ) +{ + IS31FL3736_mono_set_brightness_all( value ); +} + diff --git a/keyboards/wilba_tech/wt_mono_backlight.h b/keyboards/wilba_tech/wt_mono_backlight.h new file mode 100644 index 000000000..70031bedc --- /dev/null +++ b/keyboards/wilba_tech/wt_mono_backlight.h @@ -0,0 +1,33 @@ +/* Copyright 2018 Jason Williams (Wilba) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#pragma once + +#include <stdint.h> +#include <stdbool.h> + +void backlight_init_drivers(void); + +void backlight_timer_init(void); +void backlight_timer_enable(void); +void backlight_timer_disable(void); + +void backlight_set_suspend_state(bool state); + +void backlight_update_pwm_buffers(void); + +void backlight_set_brightness_all( uint8_t value ); + |