diff options
Diffstat (limited to 'converter/next_usb/config.h')
| -rw-r--r-- | converter/next_usb/config.h | 190 |
1 files changed, 0 insertions, 190 deletions
diff --git a/converter/next_usb/config.h b/converter/next_usb/config.h deleted file mode 100644 index a06affc5e..000000000 --- a/converter/next_usb/config.h +++ /dev/null @@ -1,190 +0,0 @@ -/* -NeXT non-ADB Keyboard USB Converter - -Copyright 2013, Benjamin Gould (bgould@github.com) - -Based on: -TMK firmware code Copyright 2011,2012 Jun WAKO <wakojun@gmail.com> -Arduino code by "Ladyada" Limor Fried (http://ladyada.net/, http://adafruit.com/), released under BSD license - -Timing reference thanks to http://m0115.web.fc2.com/ (dead link), http://cfile7.uf.tistory.com/image/14448E464F410BF22380BB -Pinouts thanks to http://www.68k.org/~degs/nextkeyboard.html -Keycodes from http://ftp.netbsd.org/pub/NetBSD/NetBSD-release-6/src/sys/arch/next68k/dev/ - -This software is licensed with a Modified BSD License. -All of this is supposed to be Free Software, Open Source, DFSG-free, -GPL-compatible, and OK to use in both free and proprietary applications. -Additions and corrections to this file are welcome. - -Redistribution and use in source and binary forms, with or without -modification, are permitted provided that the following conditions are met: - -* Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - -* Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in - the documentation and/or other materials provided with the - distribution. - -* Neither the name of the copyright holders nor the names of - contributors may be used to endorse or promote products derived - from this software without specific prior written permission. - -THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" -AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE -IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE -ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE -LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR -CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF -SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS -INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN -CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) -ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE -POSSIBILITY OF SUCH DAMAGE. - -*/ - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0xBCBC -#define DEVICE_VER 0x0500 -#define MANUFACTURER t.m.k. -#define PRODUCT NeXT Keyboard to USB converter -#define DESCRIPTION USB converter for NeXT non-ADB Keyboard - -/* matrix size */ -#define MATRIX_ROWS 12 // keycode bit: 3-0 -#define MATRIX_COLS 8 // keycode bit: 6-4 - -#define DEBUG_ON_INIT 1 - -//#define TEENSY_CONFIG 1 -//#define PRO_MICRO_CONFIG 1 -#define TMK_CONFIG 1 - -// comment out if you don't want the keyboard's LEDs to flash upon initialization or pressing shift -//#define NEXT_KBD_INIT_FLASH_LEDS -//#define NEXT_KBD_SHIFT_FLASH_LEDS - -//============= Start of Arduino Pro Micro Configuration ============== -#ifdef PRO_MICRO_CONFIG - -// this is the debugging LED that flashes when a key is being pressed -// comment out in order to disable debugging LED -#define NEXT_KBD_LED1_PORT PORTD -#define NEXT_KBD_LED1_PIN PIND -#define NEXT_KBD_LED1_DDR DDRD -#define NEXT_KBD_LED1_BIT 5 - -#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT); -#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT); - -// reserved for future use -#define NEXT_KBD_LED2_PORT PORTB -#define NEXT_KBD_LED2_PIN PINB -#define NEXT_KBD_LED2_DDR DDRB -#define NEXT_KBD_LED2_BIT 6 - -#define NEXT_KBD_LED2_ON NEXT_KBD_LED2_PORT &= ~(1<<NEXT_KBD_LED2_BIT); -#define NEXT_KBD_LED2_OFF NEXT_KBD_LED2_PORT |= (1<<NEXT_KBD_LED2_BIT); - -// corresponds to the Keyboard In wire on the NeXT connector -// (red wire in NeXT connector) - pin 2 on the Pro Micro -#define NEXT_KBD_OUT_PORT PORTD -#define NEXT_KBD_OUT_PIN PIND -#define NEXT_KBD_OUT_DDR DDRD -#define NEXT_KBD_OUT_BIT 1 - -// corresponds to the Keyboard Out wire on the NeXT connector -// (orange wire in NeXT connector) - pin 3 on the Pro Micro -#define NEXT_KBD_IN_PORT PORTD -#define NEXT_KBD_IN_PIN PIND -#define NEXT_KBD_IN_DDR DDRD -#define NEXT_KBD_IN_BIT 0 - -// this pin is an input for the power key on the NeXT keyboard -// as the keyboard is powered on this should be normally high; -// if it is pulled low it means the power button is being preseed -// (yellow wire in NeXT connector) - pin 4 on the Pro Micro -#define NEXT_KBD_PWR_PORT PORTD -#define NEXT_KBD_PWR_PIN PIND -#define NEXT_KBD_PWR_DDR DDRD -#define NEXT_KBD_PWR_BIT 4 - -#endif -//============== End of Arduino Pro Micro Configuration =============== - - -//================ Start of Teensy 2.0 Configuration ================= -#ifdef TEENSY_CONFIG - -// this is the debugging LED that flashes when a key is being pressed -// comment out in order to disable debugging LED -#define NEXT_KBD_LED_PORT PORTD -#define NEXT_KBD_LED_PIN PIND -#define NEXT_KBD_LED_DDR DDRD -#define NEXT_KBD_LED_BIT 6 - -#define NEXT_KBD_LED_ON NEXT_KBD_LED_PORT |= (1<<NEXT_KBD_LED_BIT); -#define NEXT_KBD_LED_OFF NEXT_KBD_LED_PORT &= ~(1<<NEXT_KBD_LED_BIT); - -// corresponds to the Keyboard In wire on the NeXT connector -// (red wire in NeXT connector) -#define NEXT_KBD_OUT_PORT PORTB -#define NEXT_KBD_OUT_PIN PINB -#define NEXT_KBD_OUT_DDR DDRB -#define NEXT_KBD_OUT_BIT 1 - -// corresponds to the Keyboard Out wire on the NeXT connector -// (orange wire in NeXT connector) -#define NEXT_KBD_IN_PORT PORTB -#define NEXT_KBD_IN_PIN PINB -#define NEXT_KBD_IN_DDR DDRB -#define NEXT_KBD_IN_BIT 0 - -#endif -//================= End of Teensy 2.0 Configuration ================== - - -//================ Start of TMK converter Configuration ================= -#ifdef TMK_CONFIG - -// this is the debugging LED that flashes when a key is being pressed -// comment out in order to disable debugging LED -#define NEXT_KBD_LED1_PORT PORTD -#define NEXT_KBD_LED1_PIN PIND -#define NEXT_KBD_LED1_DDR DDRD -#define NEXT_KBD_LED1_BIT 6 - -#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT); -#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT); - -// corresponds to the Keyboard In wire on the NeXT connector -#define NEXT_KBD_OUT_PORT PORTD -#define NEXT_KBD_OUT_PIN PIND -#define NEXT_KBD_OUT_DDR DDRD -#define NEXT_KBD_OUT_BIT 1 - -// corresponds to the Keyboard Out wire on the NeXT connector -#define NEXT_KBD_IN_PORT PORTD -#define NEXT_KBD_IN_PIN PIND -#define NEXT_KBD_IN_DDR DDRD -#define NEXT_KBD_IN_BIT 0 - -// this pin is an input for the power key on the NeXT keyboard -// as the keyboard is powered on this should be normally high; -// if it is pulled low it means the power button is being preseed -#define NEXT_KBD_PWR_PORT PORTD -#define NEXT_KBD_PWR_PIN PIND -#define NEXT_KBD_PWR_DDR DDRD -#define NEXT_KBD_PWR_BIT 4 - -#endif -//================= End of TMK converter Configuration ================== - -/* key combination for command */ -#define IS_COMMAND() ( \ - (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT))) || \ - (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RALT))) || \ - (keyboard_report->mods == (MOD_BIT(KC_RGUI) | MOD_BIT(KC_RGUI))) \ -) |