diff options
Diffstat (limited to 'converter/pc98_usb/config.h')
| -rw-r--r-- | converter/pc98_usb/config.h | 123 |
1 files changed, 0 insertions, 123 deletions
diff --git a/converter/pc98_usb/config.h b/converter/pc98_usb/config.h deleted file mode 100644 index b8d676e4c..000000000 --- a/converter/pc98_usb/config.h +++ /dev/null @@ -1,123 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x9898 -#define DEVICE_VER 0x0100 -#define MANUFACTURER t.m.k. -#define PRODUCT PC98 keyboard converter -#define DESCRIPTION converts PC98 keyboard protocol into USB - - -/* matrix size */ -#define MATRIX_ROWS 16 -#define MATRIX_COLS 8 - -/* key combination for command */ -#define IS_COMMAND() ( \ - host_get_first_key() == KC_CANCEL \ -) - - -/* PC98 Reset Port shared with TXD */ -#define PC98_RST_DDR DDRD -#define PC98_RST_PORT PORTD -#define PC98_RST_BIT 3 -/* PC98 Ready Port */ -#define PC98_RDY_DDR DDRD -#define PC98_RDY_PORT PORTD -#define PC98_RDY_BIT 4 -/* PC98 Retry Port */ -#define PC98_RTY_DDR DDRD -#define PC98_RTY_PORT PORTD -#define PC98_RTY_BIT 5 - -/* - * PC98 Serial(USART) configuration - * asynchronous, positive logic, 19200baud, bit order: LSB first - * 1-start bit, 8-data bit, odd parity, 1-stop bit - */ -/* - * Software Serial - */ -#define SERIAL_SOFT_BAUD 19200 -#define SERIAL_SOFT_PARITY_ODD -#define SERIAL_SOFT_BIT_ORDER_LSB -#define SERIAL_SOFT_LOGIC_POSITIVE -/* RXD Port */ -#define SERIAL_SOFT_RXD_DDR DDRD -#define SERIAL_SOFT_RXD_PORT PORTD -#define SERIAL_SOFT_RXD_PIN PIND -#define SERIAL_SOFT_RXD_BIT 2 -#define SERIAL_SOFT_RXD_READ() (SERIAL_SOFT_RXD_PIN&(1<<SERIAL_SOFT_RXD_BIT)) -/* RXD Interupt */ -#define SERIAL_SOFT_RXD_VECT INT2_vect -#define SERIAL_SOFT_RXD_INIT() do { \ - /* pin configuration: input with pull-up */ \ - SERIAL_SOFT_RXD_DDR &= ~(1<<SERIAL_SOFT_RXD_BIT); \ - SERIAL_SOFT_RXD_PORT |= (1<<SERIAL_SOFT_RXD_BIT); \ - /* enable interrupt: INT2(falling edge) */ \ - EICRA |= ((1<<ISC21)|(0<<ISC20)); \ - EIMSK |= (1<<INT2); \ - sei(); \ -} while (0) -#define SERIAL_SOFT_RXD_INT_ENTER() -#define SERIAL_SOFT_RXD_INT_EXIT() do { \ - /* clear interrupt flag */ \ - EIFR = (1<<INTF2); \ -} while (0) -/* TXD Port */ -#define SERIAL_SOFT_TXD_DDR DDRD -#define SERIAL_SOFT_TXD_PORT PORTD -#define SERIAL_SOFT_TXD_PIN PIND -#define SERIAL_SOFT_TXD_BIT 3 -#define SERIAL_SOFT_TXD_HI() do { SERIAL_SOFT_TXD_PORT |= (1<<SERIAL_SOFT_TXD_BIT); } while (0) -#define SERIAL_SOFT_TXD_LO() do { SERIAL_SOFT_TXD_PORT &= ~(1<<SERIAL_SOFT_TXD_BIT); } while (0) -#define SERIAL_SOFT_TXD_INIT() do { \ - /* pin configuration: output */ \ - SERIAL_SOFT_TXD_DDR |= (1<<SERIAL_SOFT_TXD_BIT); \ - /* idle */ \ - SERIAL_SOFT_TXD_ON(); \ -} while (0) - - -/* - * Hardware Serial(UART) - */ -#ifdef __AVR_ATmega32U4__ - #define SERIAL_UART_BAUD 19200 - #define SERIAL_UART_DATA UDR1 - #define SERIAL_UART_UBRR ((F_CPU/(16UL*SERIAL_UART_BAUD))-1) - #define SERIAL_UART_RXD_VECT USART1_RX_vect - #define SERIAL_UART_TXD_READY (UCSR1A&(1<<UDRE1)) - #define SERIAL_UART_INIT() do { \ - UBRR1L = (uint8_t) SERIAL_UART_UBRR; /* baud rate */ \ - UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8); /* baud rate */ \ - UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); /* RX interrupt, RX: enable */ \ - UCSR1B |= (0<<TXCIE1) | (1<<TXEN1); /* TX interrupt, TX: enable */ \ - UCSR1C |= (1<<UPM11) | (1<<UPM10); /* parity: none(00), even(01), odd(11) */ \ - sei(); \ - } while(0) -#else - #error "USART configuration is needed." -#endif - - -#endif |