diff options
Diffstat (limited to 'converter/x68k_usb/Makefile')
| -rw-r--r-- | converter/x68k_usb/Makefile | 101 |
1 files changed, 0 insertions, 101 deletions
diff --git a/converter/x68k_usb/Makefile b/converter/x68k_usb/Makefile deleted file mode 100644 index 60e9a5746..000000000 --- a/converter/x68k_usb/Makefile +++ /dev/null @@ -1,101 +0,0 @@ -# -# Makefile for PJRC Teensy -# - - -# Target file name (without extension). -TARGET = x68k_usb_pjrc - -# Directory common source filess exist -TMK_DIR = ../../tmk_core - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ - led.c \ - protocol/serial_uart.c - -CONFIG_H = config_pjrc.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Boot Section Size in bytes -# Teensy halfKay 512 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# *Comment out* to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA - - - -#---------------- Programming Options -------------------------- -AVRDUDE = avrdude -# Type: avrdude -c ? to get a full listing. -AVRDUDE_PROGRAMMER = avr109 -AVRDUDE_PORT = /dev/ttyACM0 -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep - -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y - -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v - -AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) - -#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) -#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex -PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TMK_DIR) - - -include $(TMK_DIR)/protocol/pjrc.mk -include $(TMK_DIR)/protocol.mk -include $(TMK_DIR)/common.mk -include $(TMK_DIR)/rules.mk |