diff options
Diffstat (limited to 'keyboard/hid_liber/Makefile.pjrc')
| -rw-r--r-- | keyboard/hid_liber/Makefile.pjrc | 111 |
1 files changed, 0 insertions, 111 deletions
diff --git a/keyboard/hid_liber/Makefile.pjrc b/keyboard/hid_liber/Makefile.pjrc deleted file mode 100644 index 326bbe86f..000000000 --- a/keyboard/hid_liber/Makefile.pjrc +++ /dev/null @@ -1,111 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# Target file name (without extension). -TARGET = hid_liber_pjrc - -# Directory common source filess exist -TMK_DIR = ../../tmk_core - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ - led.c - -CONFIG_H = config.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Boot Section Size in bytes -# Teensy halfKay 512 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -#MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TMK_DIR) - -include $(TMK_DIR)/protocol/pjrc.mk -include $(TMK_DIR)/common.mk -include $(TMK_DIR)/rules.mk - -ansi: OPT_DEFS += -DLAYOUT_ANSI -ansi: all - -iso: OPT_DEFS += -DLAYOUT_ISO -iso: all - -custom: OPT_DEFS += -DLAYOUT_CUSTOM -custom: all - -alaricljs: OPT_DEFS += -DLAYOUT_ALARICLJS -alaricljs: all |