diff options
Diffstat (limited to 'keyboards/arrow_pad')
| -rw-r--r-- | keyboards/arrow_pad/Makefile | 73 | ||||
| -rw-r--r-- | keyboards/arrow_pad/readme.md | 119 | ||||
| -rw-r--r-- | keyboards/arrow_pad/rules.mk | 70 |
3 files changed, 185 insertions, 77 deletions
diff --git a/keyboards/arrow_pad/Makefile b/keyboards/arrow_pad/Makefile index 09fcf3e7a..4e2a6f00f 100644 --- a/keyboards/arrow_pad/Makefile +++ b/keyboards/arrow_pad/Makefile @@ -1,74 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= yes # USB Nkey Rollover -BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/arrow_pad/readme.md b/keyboards/arrow_pad/readme.md index 5aa44cce5..d0d172272 100644 --- a/keyboards/arrow_pad/readme.md +++ b/keyboards/arrow_pad/readme.md @@ -1,24 +1,133 @@ arrow_pad keyboard firmware ====================== +## Keyboard Info + +The ArrowPad is a wired conversion that can be made to any stand-alone keypad. It uses two main layers - a standard numpad, and a more advanced arrow cluster navigator. + +The first 24-key ArrowPad was handwired, but the PCB was wired as listed below. + +``` +<Chip Ref Des> pin <Pin #> +<Keycap Name> (Silkscreen Name if different) - <Switch Pin #> + + +Note: +U2 pin 2 is the Num Lock LED and is active low. + +U2 pin 1 +Clear (Num Lock) - 1 +Enter - 2 +Esc (ESC) - 2 + + +U2 pin 3 +- - 1 + +U2 pin 4 +7 - 2 +8 - 2 +9 - 2 + +U2 pin 5 +* - 2 +Delete (BACK SPACE) - 2 + +U2 pin 6 +1 - 2 +0 - 2 +. - 2 +, - 2 + +U2 pin 7 +4 - 2 +5 - 2 +6 - 2 + +U2 pin 8 +Tab - 2 += (/) - 2 + +U2 pin 13 +Delete (BACK SPACE) - 1 +9 - 1 +6 - 1 +3 - 1 +. - 1 + +U2 pin 14 +Tab - 1 +8 - 1 +5 - 1 +2 - 1 +0 - 1 + +U2 pin 15 +Esc (ESC) - 1 += (/) - 1 +/ (*) - 1 +7 - 1 +4 - 1 +1 - 1 ++ - 1 + +U2 pin 16 +Enter - 1 +* (<--) - 1 +, - 1 + +U2 pin 17 +Fn (#NAME?) - 1 +- - 2 +Clear (Num Lock) - 2 + +U2 pin 18 +Fn (#NAME?) - 2 +* (<--) - 2 ++ - 2 +3 - 2 +2 - 2 +``` + +More info can be found on [GeekHack](https://geekhack.org/index.php?topic=73632.msg1802497#msg1802497) + +The second ArrowPad was a conversion from a 21-key Genovation keypad. It used a 2 row x 11 column matrix. + +``` +#define KEYMAP( \ + KM_ESC, KM_TAB, KM_BSL, KM_ARR, \ + KM_NUM, KM_FSL, KM_AST, KM_MIN, \ + KM___7, KM___8, KM___9, ___PLS, \ + KM___4, KM___5, KM___6, KM_PLS, \ + KM___1, KM___2, KM___3, ___ENT, \ + KM___0, _____0, KM_DOT, KM_ENT \ +) { \ + { KM_ESC, KM_TAB, KM_BSL, KM_ARR, KM___7, KM___8, KM___9, KM_PLS, KM___1, KM___2, KM___3, }, \ + { KM_NUM, KM_FSL, KM_AST, KM_MIN, KM___4, KM___5, KM___6, KM_ENT, KC_NO, KM___0, KM_DOT, }, \ +} +``` + + ## Quantum MK Firmware For the full Quantum feature list, see [the parent readme.md](/readme.md). ## Building -Download or clone the whole firmware and navigate to the keyboards/arrow_pad folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. +Download or clone the whole firmware and navigate to the keyboards/arrow_pad folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|<name>] +$ make [default|pad_21|pad_24|<name>] ``` -Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
\ No newline at end of file + +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/arrow_pad/rules.mk b/keyboards/arrow_pad/rules.mk new file mode 100644 index 000000000..3dca9b6ea --- /dev/null +++ b/keyboards/arrow_pad/rules.mk @@ -0,0 +1,70 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes # USB Nkey Rollover +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6
\ No newline at end of file |