diff options
Diffstat (limited to 'keyboards/atreus')
22 files changed, 1014 insertions, 102 deletions
diff --git a/keyboards/atreus/Makefile b/keyboards/atreus/Makefile index 95ee1d4d7..4e2a6f00f 100644 --- a/keyboards/atreus/Makefile +++ b/keyboards/atreus/Makefile @@ -1,88 +1,3 @@ - - -ifdef TEENSY2 - OPT_DEFS += -DATREUS_TEENSY2 - ATRUES_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex -else - OPT_DEFS += -DATREUS_ASTAR - OPT_DEFS += -DCATERINA_BOOTLOADER - ATRUES_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ - avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) -endif - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend -NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA -# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality -# MIDI_ENABLE ?= YES # MIDI controls -UNICODE_ENABLE ?= YES # Unicode -# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID - - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - -USB ?= /dev/cu.usbmodem1411 - -upload: build - $(ATRUES_UPLOAD_COMMAND) -
\ No newline at end of file +endif
\ No newline at end of file diff --git a/keyboards/atreus/atreus.h b/keyboards/atreus/atreus.h index 2b3803bc2..f841c3519 100644 --- a/keyboards/atreus/atreus.h +++ b/keyboards/atreus/atreus.h @@ -10,16 +10,16 @@ // The first section contains all of the arguements // The second converts the arguments into a two-dimensional array #define KEYMAP( \ - k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, \ - k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, \ - k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, \ - k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b \ ) \ { \ { k00, k01, k02, k03, k04, KC_NO, k05, k06, k07, k08, k09 }, \ { k10, k11, k12, k13, k14, KC_NO, k15, k16, k17, k18, k19 }, \ { k20, k21, k22, k23, k24, k35, k25, k26, k27, k28, k29 }, \ - { k2a, k30, k31, k32, k33, k34, k36, k37, k38, k39, k3a } \ + { k30, k31, k32, k33, k34, k36, k37, k38, k39, k3a, k3b } \ } #endif diff --git a/keyboards/atreus/config.h b/keyboards/atreus/config.h index 624d90188..51162cde3 100644 --- a/keyboards/atreus/config.h +++ b/keyboards/atreus/config.h @@ -37,7 +37,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. // COLS: Left to right, ROWS: Top to bottom #if defined(ATREUS_ASTAR) # define MATRIX_ROW_PINS { D0, D1, D3, D2 } +#if defined(PCBDOWN) +# define MATRIX_COL_PINS { B7, D6, F7, F6, B6, D4, E6, B4, B5, C6, D7 } +#else # define MATRIX_COL_PINS { D7, C6, B5, B4, E6, D4, B6, F6, F7, D6, B7 } +#endif # define UNUSED_PINS #elif defined(ATREUS_TEENSY2) # define MATRIX_ROW_PINS { D0, D1, D2, D3 } diff --git a/keyboards/atreus/keymaps/alphadox/config.h b/keyboards/atreus/keymaps/alphadox/config.h new file mode 100644 index 000000000..df56849b0 --- /dev/null +++ b/keyboards/atreus/keymaps/alphadox/config.h @@ -0,0 +1,80 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ + +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Arbitrary Definitions +#define PRODUCT Planckeus +#define DESCRIPTION q.m.k. keyboard firmware for Planckeus + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 11 + +#define MATRIX_ROW_PINS { D0, D1, D2, D3 } +#define MATRIX_COL_PINS { F6, F5, F4, F1, F0, F7, B0, B1, B2, B3, B7 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +//#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/atreus/keymaps/alphadox/keymap.c b/keyboards/atreus/keymaps/alphadox/keymap.c new file mode 100644 index 000000000..b8ec0e032 --- /dev/null +++ b/keyboards/atreus/keymaps/alphadox/keymap.c @@ -0,0 +1,45 @@ +#include "atreus.h" + +#define BASE 0 +#define SYMB 1 +#define ETC 2 + +enum macro_id { + TEENSY, +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[BASE] = KEYMAP( + KC_Q, KC_W, KC_D, KC_F, KC_K, KC_J, KC_U, KC_R, KC_L, KC_SCLN, + LT(ETC,KC_A), KC_S, KC_E, KC_T, KC_G, KC_Y, KC_N, KC_I, KC_O, KC_H, + SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, KC_P, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH), + KC_GRV, KC_DEL, KC_LALT, GUI_T(KC_TAB), LT(SYMB,KC_BSPC), CTL_T(KC_ESC), SFT_T(KC_ENT), LT(SYMB,KC_SPC), GUI_T(KC_LEFT), KC_DOWN, KC_UP, LCAG_T(KC_RGHT) +), + +[SYMB] = KEYMAP( + KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_EQL, KC_7, KC_8, KC_9, KC_PLUS, + KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_BSLS, KC_MINS, KC_4, KC_5, KC_6, KC_QUOT, + KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_ASTR, KC_UNDS, KC_1, KC_2, KC_3, KC_DQUO, + KC_TILD, KC_AMPR, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_0, KC_NO, KC_DOT, KC_TRNS +), + +[ETC] = KEYMAP( + RESET, KC_NO, KC_NO, KC_NO, KC_PGUP, KC_VOLU, KC_F7, KC_F8, KC_F9, KC_HOME, + LT(ETC,KC_A), KC_NO, KC_NO, KC_NO, KC_PGDN, KC_VOLD, KC_F4, KC_F5, KC_F6, KC_END, + KC_NO, KC_NO, KC_NO, KC_NO, KC_DEL, KC_MUTE, KC_F1, KC_F2, KC_F3, KC_INS, + KC_TRNS, KC_NO, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_NO, KC_NO +), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) { + switch(id) { + case TEENSY: + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/atreus/keymaps/classic/keymap.c b/keyboards/atreus/keymaps/classic/keymap.c new file mode 100644 index 000000000..6ca0b2077 --- /dev/null +++ b/keyboards/atreus/keymaps/classic/keymap.c @@ -0,0 +1,48 @@ +#include "atreus.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QW 0 +#define _RS 1 +#define _LW 2 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[_QW] = { /* Qwerty */ + {KC_Q, KC_W, KC_E, KC_R, KC_T, KC_TRNS, KC_Y, KC_U, KC_I, KC_O, KC_P }, + {KC_A, KC_S, KC_D, KC_F, KC_G, KC_TRNS, KC_H, KC_J, KC_K, KC_L, KC_SCLN }, + {KC_Z, KC_X, KC_C, KC_V, KC_B, KC_LALT, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH }, + {KC_ESC, KC_TAB, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, MO(_RS), KC_MINS, KC_QUOT, KC_ENT } +}, +[_RS] = { /* [> RAISE <] */ + {KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_TRNS, KC_PGUP, KC_7, KC_8, KC_9, KC_ASTR}, + {KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_GRV, KC_TRNS, KC_PGDN, KC_4, KC_5, KC_6, KC_PLUS}, + {KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_TILD, KC_LALT, KC_AMPR, KC_1, KC_2, KC_3, KC_BSLS}, + {TG(_LW), KC_INS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, KC_TRNS, KC_DOT, KC_0, KC_EQL} +}, +[_LW] = { /* [> LOWER <] */ + {KC_INS, KC_HOME, KC_UP, KC_END, KC_PGUP, KC_TRNS, KC_UP, KC_F7, KC_F8, KC_F9, KC_F10}, + {KC_DELT, KC_LEFT, KC_DOWN, KC_RGHT, KC_DOWN, KC_TRNS, KC_DOWN, KC_F4, KC_F5, KC_F6, KC_F11}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_LALT, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F12}, + {KC_TRNS, KC_TRNS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, DF(_QW), KC_TRNS, KC_TRNS, RESET} +}}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/atreus/keymaps/default/keymap.c b/keyboards/atreus/keymaps/default/keymap.c index 1c4280ff5..04ad66fed 100644 --- a/keyboards/atreus/keymaps/default/keymap.c +++ b/keyboards/atreus/keymaps/default/keymap.c @@ -18,17 +18,29 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { {KC_Z, KC_X, KC_C, KC_V, KC_B, KC_LALT, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH }, {KC_ESC, KC_TAB, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, MO(_RS), KC_MINS, KC_QUOT, KC_ENT } }, +/* + * ! @ up { } || pgup 7 8 9 * + * # left down right $ || pgdn 4 5 6 + + * [ ] ( ) & || ` 1 2 3 \ + * lower insert super shift bksp ctrl || alt space fn . 0 = + */ [_RS] = { /* [> RAISE <] */ - {KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_PIPE, KC_TRNS, KC_PGUP, KC_7, KC_8, KC_9, KC_ASTR}, - {KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_GRV, KC_TRNS, KC_PGDN, KC_4, KC_5, KC_6, KC_PLUS}, - {KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_TILD, KC_LALT, KC_AMPR, KC_1, KC_2, KC_3, KC_BSLS}, + {KC_EXLM, KC_AT, KC_UP, KC_LCBR, KC_RCBR, KC_TRNS, KC_PGUP, KC_7, KC_8, KC_9, KC_ASTR}, + {KC_HASH, KC_LEFT, KC_DOWN, KC_RGHT, KC_DLR, KC_TRNS, KC_PGDN, KC_4, KC_5, KC_6, KC_PLUS}, + {KC_LBRC, KC_RBRC, KC_LPRN, KC_RPRN, KC_AMPR, KC_LALT, KC_GRV, KC_1, KC_2, KC_3, KC_BSLS}, {TG(_LW), KC_INS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, KC_TRNS, KC_DOT, KC_0, KC_EQL} }, +/* + * insert home up end pgup || up F7 F8 F9 F10 + * del left down right pgdn || down F4 F5 F6 F11 + * volup reset || F1 F2 F3 F12 + * voldn super shift bksp ctrl || alt space L0 prtsc scroll pause + */ [_LW] = { /* [> LOWER <] */ {KC_INS, KC_HOME, KC_UP, KC_END, KC_PGUP, KC_TRNS, KC_UP, KC_F7, KC_F8, KC_F9, KC_F10}, {KC_DELT, KC_LEFT, KC_DOWN, KC_RGHT, KC_DOWN, KC_TRNS, KC_DOWN, KC_F4, KC_F5, KC_F6, KC_F11}, - {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_LALT, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F12}, - {KC_TRNS, KC_TRNS, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, DF(_QW), KC_TRNS, KC_TRNS, RESET} + {KC_TRNS, KC_VOLU, KC_TRNS, KC_TRNS, RESET, KC_LALT, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F12}, + {KC_TRNS, KC_VOLD, KC_LGUI, KC_LSFT, KC_BSPC, KC_LCTL, KC_SPC, DF(_QW), KC_PSCR, KC_SLCK, KC_PAUS} }}; const uint16_t PROGMEM fn_actions[] = { diff --git a/keyboards/atreus/keymaps/erlandsona/config.h b/keyboards/atreus/keymaps/erlandsona/config.h new file mode 100644 index 000000000..d9eb1903e --- /dev/null +++ b/keyboards/atreus/keymaps/erlandsona/config.h @@ -0,0 +1,96 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + + +/* Make Overloaded Keys switch faster */ +#define TAPPING_TERM 150 + +/* USB Device descriptor parameter */ + +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Technomancy +#define PRODUCT Atreus +#define DESCRIPTION q.m.k. keyboard firmware for Atreus + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 11 + +// Change this to how you wired your keyboard +// COLS: Left to right, ROWS: Top to bottom +#if defined(ATREUS_ASTAR) +# define MATRIX_ROW_PINS { D0, D1, D3, D2 } +#if defined(PCBDOWN) +# define MATRIX_COL_PINS { B7, D6, F7, F6, B6, D4, E6, B4, B5, C6, D7 } +#else +# define MATRIX_COL_PINS { D7, C6, B5, B4, E6, D4, B6, F6, F7, D6, B7 } +#endif +# define UNUSED_PINS +#elif defined(ATREUS_TEENSY2) +# define MATRIX_ROW_PINS { D0, D1, D2, D3 } +# define MATRIX_COL_PINS { F6, F5, F4, B7, B6, B5, B4, B3, B2, B1, B0 } +# define UNUSED_PINS +#endif + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +//#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/atreus/keymaps/erlandsona/keymap.c b/keyboards/atreus/keymaps/erlandsona/keymap.c new file mode 100644 index 000000000..32c8826e0 --- /dev/null +++ b/keyboards/atreus/keymaps/erlandsona/keymap.c @@ -0,0 +1,61 @@ +// this is the style you want to emulate. +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, + +#include "atreus.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define BASE 0 +#define NUMS 1 +#define MOUS 2 + +// Some quick aliases, just to make it look pretty +#define _______ KC_TRNS +#define XXXXXXX KC_NO + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[BASE] = KEYMAP( /* Qwerty */ + KC_Q , KC_W , KC_E , KC_R , KC_T , KC_Y , KC_U , KC_I , KC_O , KC_P , + KC_A , KC_S , KC_D , KC_F , KC_G , KC_H , KC_J , KC_K , KC_L , KC_SCLN , + SFT_T(KC_Z), KC_X , KC_C , KC_V , KC_B , KC_N , KC_M , KC_COMM, KC_DOT , SFT_T(KC_QUOT), + KC_LCTL , KC_LALT, KC_LALT, KC_LGUI, KC_BSPC, KC_ESC, KC_ENT, KC_SPC, F(NUMS), KC_RALT, KC_SLSH, KC_BSLS ), + +[NUMS] = KEYMAP( /* Numbers / Arrows / Symbols */ + KC_GRV , KC_1 , KC_2 , KC_3 , KC_4 , KC_LPRN, KC_RPRN, KC_MINS, KC_EQL , KC_LBRC, + KC_TAB , KC_5 , KC_6 , KC_7 , KC_8 , KC_LEFT, KC_DOWN, KC_UP , KC_RGHT, KC_RBRC, + _______, KC_9 , KC_0 , KC_DOT , KC_COMM, KC_HOME, KC_PGDN, KC_PGUP, KC_END , _______, + _______, _______, _______, _______, KC_DEL , F(MOUS), _______, _______, _______, _______, _______, _______), + +[MOUS] = KEYMAP( /* Mouse and Media Keys */ + KC_SLCK, KC_PAUSE, KC_F11 , KC_F10 , KC_F9 , KC_F8 , KC_F7 , KC_F6 , KC_F5 , KC_F4, + KC_VOLD, KC_ACL0 , KC_ACL1, KC_ACL2, KC_VOLU, KC_MS_L, KC_MS_D, KC_MS_U, KC_MS_R, KC_F3, + KC_MUTE, KC_MPRV , KC_MPLY, KC_MNXT, KC_MUTE, KC_WH_R, KC_WH_U, KC_WH_D, KC_WH_L, KC_F2, + _______, _______ , _______, _______, _______, _______, _______, KC_BTN1, F(BASE), RESET , KC_F12 , KC_F1) +}; + + +// I prefer this layer switching strategy to the TG and MO functions. +// so that I can get out of mouse mode just by tapping/holding my base layer FN key. +const uint16_t PROGMEM fn_actions[] = { + [BASE] = ACTION_LAYER_OFF(2, 1), // switch back to layer 0 + [NUMS] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay + [MOUS] = ACTION_LAYER_ON(2, 1) // switch to layer 2 +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/atreus/keymaps/jeremy/keymap.c b/keyboards/atreus/keymaps/jeremy/keymap.c new file mode 100644 index 000000000..90ec6f904 --- /dev/null +++ b/keyboards/atreus/keymaps/jeremy/keymap.c @@ -0,0 +1,66 @@ +// This is the personal keymap of Jeremy Cowgar (@jcowgar). It is written for the programmer. + +#include "atreus.h" +#include "action_layer.h" +#include "keymap_colemak.h" + +#define PREVENT_STUCK_MODIFIERS + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +#define ALPH 0 +#define NUMS 1 +#define CURS 2 +#define SYMB 3 +#define FKEY 4 + +// Some handy macros to keep the keymaps clean and easier to maintain +#define KM_SAVE LGUI(CM_S) +#define KM_CLSE LGUI(CM_W) +#define KM_OPEN LGUI(CM_O) + +#define KM_COPY LGUI(KC_C) +#define KM_CUT LGUI(KC_X) +#define KM_PAST LGUI(KC_V) +#define KM_UNDO LGUI(KC_Z) +#define KM_REDO LGUI(LSFT(KC_Z)) + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[ALPH] = { + {KC_Q, KC_W, KC_E, KC_R, KC_T, KC_TRNS, KC_Y, KC_U, KC_I, KC_O, KC_P}, + {KC_A, LT(NUMS, KC_S), LT(FKEY, KC_D), KC_F, KC_G, KC_TRNS, KC_H, KC_J, LT(CURS, KC_K), LT(SYMB, KC_L), KC_SCLN}, + {KC_Z, KC_X, KC_C, KC_V, KC_B, KC_LALT, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH}, + {KC_LCTL, KC_ESC, KC_NO, KC_LSFT, KC_SPC, KC_LGUI, KC_ENT, KC_RSFT, KC_NO, KC_ESC, KC_RCTL} +}, +[NUMS] = { + {KC_TRNS, KC_TRNS, KC_TRNS, KC_ASTR, KC_SLSH, KC_TRNS, KC_TRNS, KC_7, KC_8, KC_9, KC_SLSH}, + {KC_TRNS, KC_TRNS, KC_EQL, KC_PLUS, KC_MINS, KC_TRNS, KC_LPRN, KC_4, KC_5, KC_6, KC_ASTR}, + {KC_TRNS, KC_TRNS, KC_DOT, KC_COMM, CM_SCLN, KC_TRNS, KC_RPRN, KC_1, KC_2, KC_3, KC_MINS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_0, KC_DOT, KC_EQL, KC_PLUS} +}, +[CURS] = { + {KC_TRNS, KC_BSPC, KC_UP, KC_DELT, KC_PGUP, KC_TRNS, KC_TRNS, KM_SAVE, KC_TRNS, KM_OPEN, KC_TRNS}, + {KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_PGDN, KC_TRNS, KM_UNDO, KC_LALT, KC_TRNS, KC_LGUI, KC_TRNS}, + {KC_TRNS, KC_VOLD, KC_MUTE, KC_VOLU, KC_MPLY, KM_COPY, KM_REDO, KM_CLSE, KC_TRNS, KC_TRNS, KC_TRNS}, + {KC_TRNS, KC_TRNS, RESET, KC_TRNS, KC_TAB, KM_CUT, KM_PAST, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS} +}, +[SYMB] = { + {KC_BSLS, KC_EXLM, KC_LABK, KC_RABK, CM_COLN, KC_TRNS, KC_UNDS, KC_DLR, KC_QUES, KC_TRNS, KC_PERC}, + {KC_AT, KC_AMPR, KC_LPRN, KC_RPRN, CM_SCLN, KC_TRNS, KC_COMM, KC_DOT, KC_QUOT, KC_TRNS, KC_TILD}, + {KC_HASH, KC_PIPE, KC_LCBR, KC_RCBR, KC_SLSH, KC_TRNS, KC_TRNS, KC_GRV, KC_DQT, KC_TRNS, KC_CIRC}, + {KC_TRNS, KC_TRNS, KC_LBRC, KC_RBRC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS} +}, +[FKEY] = { + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F9, KC_F10, KC_F11, KC_F12}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F5, KC_F6, KC_F7, KC_F8}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_F1, KC_F2, KC_F3, KC_F4}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS} +}}; + +const uint16_t PROGMEM fn_actions[] = {}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + switch(id) {} + + return MACRO_NONE; +}; diff --git a/keyboards/atreus/keymaps/jeremy/readme.md b/keyboards/atreus/keymaps/jeremy/readme.md new file mode 100644 index 000000000..df0179a8e --- /dev/null +++ b/keyboards/atreus/keymaps/jeremy/readme.md @@ -0,0 +1,45 @@ +Jeremy's Atreus Key Mapping +=========================== + +I am a programmer by trade that suffers from the beginning stages of RSI. As a programmer I use letters, symbols and cursor navigation most often. To prevent strange finger gymnastics, I wrote a script to rank which non-letter characters occurred in my primary source projects most often and then placed these characters in the easiest to reach locations, for me. I made heavy use of momentary layer toggling. + +My layout is also geared toward a software based Colemak mapping. I would like it to be hardware, but I use my Laptop on the go frequently and thus my laptop keyboard. I have moved the keycaps to reflect the Colemak layout. My laptop is a MacBook Pro (2015). + +## Main Layers + +1. [Letters](http://www.keyboard-layout-editor.com/#/gists/6861cb9df09ce78efaddf8aa7471e3ac) +2. [Symbols](http://www.keyboard-layout-editor.com/#/gists/8956a18b508a78e93b9c38ec3fcccaa5) +3. [Navigation](http://www.keyboard-layout-editor.com/#/gists/6ed492b714a7f54eb1c5de09b87fd8c4) +4. [Numbers](http://www.keyboard-layout-editor.com/#/gists/399ceb5624e8388e48a3a5eacac8e973) +5. [Function Keys](http://www.keyboard-layout-editor.com/#/gists/7fd7dc24c7048316f3724b1893c64e89) + +## Notes + +### General + +Some characters can be accessed multiple ways. This was done because you may be in a given layer, such as numbers, where when doing math, you may need quick access to the parentheses characters for grouping. This prevents some layer switching. + +I own an ErgoDox and plan on porting this as a base layer, then using the extra keys the ErgoDox provides accordingly. My goal, though, is to be fully functional on this base setup and build everything into muscle memory. + +### Symbol Layer + +1. I placed characters that deal with an if statement close together, such as !, & and |. +2. All matching brace/bracket characters are together as well. + +### Number Layer + +1. Everything I did was a compromise when trying to mimic a ten-key. I did the best I could. +2. Operators are duplicated on the right and left. I do not find it comfortable to use my pinky much, so I tend to use my left hand for +, -, * and / but those were also placed on the right hand to mimic the ten-key. +3. Parentheses were added for typing on the calculator. + +### Cursor Layer + +1. It includes basic audio controls because they didn't really fit anywhere else +2. It contains basic file manipulation. I'm not sure that was a good idea. I do save all the time, but Cmd+S isn't exactly hard. +3. It contains the backspace and delete keys right on top of the left and right arrows. +4. Cmd and Opt keys are duplicated. This makes for very easy navigation, for example on a Mac, Opt+Left/Right moves word by word. It also backspaces or deletes word by word. + +### Function Layer + +1. Almost all other layers I saw grouped the F keys into a bunch of three. This only gives nine function keys in order if you attempt to stay as close to the home row as possible. I went with a group of four, which gives all twelve function keys to the right hand, one row below and above the home row. +2. I duplicated the Command and Option keys the same as on the cursor layer. This makes it dead easy to hit modified function keys such as Cmd+Opt+F5. It's also easy to toss in a Shift modifier in there with the right thumb since the bottom row is preserved. diff --git a/keyboards/atreus/keymaps/replicaJunction/atreus-replica-base.png b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-base.png Binary files differnew file mode 100644 index 000000000..1d5bd78db --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-base.png diff --git a/keyboards/atreus/keymaps/replicaJunction/atreus-replica-extend.png b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-extend.png Binary files differnew file mode 100644 index 000000000..cf4db3e2c --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-extend.png diff --git a/keyboards/atreus/keymaps/replicaJunction/atreus-replica-function.png b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-function.png Binary files differnew file mode 100644 index 000000000..30e5621e4 --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-function.png diff --git a/keyboards/atreus/keymaps/replicaJunction/atreus-replica-game.png b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-game.png Binary files differnew file mode 100644 index 000000000..95f8be5e0 --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-game.png diff --git a/keyboards/atreus/keymaps/replicaJunction/atreus-replica-num.png b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-num.png Binary files differnew file mode 100644 index 000000000..3c445f90c --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/atreus-replica-num.png diff --git a/keyboards/atreus/keymaps/replicaJunction/config.h b/keyboards/atreus/keymaps/replicaJunction/config.h new file mode 100644 index 000000000..437aa662c --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/config.h @@ -0,0 +1,94 @@ +/* +Config file - Atreus QMK with replicaJunction layout + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ + +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER Technomancy +#define PRODUCT Atreus +#define DESCRIPTION q.m.k. keyboard firmware for Atreus + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 11 + +// Change this to how you wired your keyboard +// COLS: Left to right, ROWS: Top to bottom +#if defined(ATREUS_ASTAR) +# define MATRIX_ROW_PINS { D0, D1, D3, D2 } +# define MATRIX_COL_PINS { D7, C6, B5, B4, E6, D4, B6, F6, F7, D6, B7 } +# define UNUSED_PINS +#elif defined(ATREUS_TEENSY2) +# define MATRIX_ROW_PINS { D0, D1, D2, D3 } +# define MATRIX_COL_PINS { F6, F5, F4, B7, B6, B5, B4, B3, B2, B1, B0 } +# define UNUSED_PINS +#endif + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +//#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +// Default: 5 +#define DEBOUNCING_DELAY 6 + +// I don't have any locking keys, so I don't need these features + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +//#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +//#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* Prevent modifiers from sticking when switching layers */ +#define PREVENT_STUCK_MODIFIERS + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/atreus/keymaps/replicaJunction/keymap.c b/keyboards/atreus/keymaps/replicaJunction/keymap.c new file mode 100644 index 000000000..d39a184d4 --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/keymap.c @@ -0,0 +1,213 @@ +/* + * Keyboard: Atreus + * Keymap: replicaJunction + * Version: 0.4 + * + * This keymap is designed to complement my Ergodox keyboard layout, found in keyboards/ergodox_ez. + * The Atreus keyboard is a 40% board whose design was heavily influenced by the Ergodox. I now + * have both keyboards, so I've designed these layouts in an effort to make switching between the + * two as easy as possible. + * + * Clearly, the Atreus is the limiting factor in this equation, so I've taken heavy advantage of + * function and dual-role keys. + * + * The default key layout in this keymap is Colemak-ModDH. Information on that layout can be found + * here: https://colemakmods.github.io/mod-dh/ + */ + +#include "atreus.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +// Note that whatever is set as layer 0 will be the default layer of the keyboard. + +#define _CO 0 // Colemak +#define _QW 1 // QWERTY +#define _GA 2 // Gaming +#define _EX 3 // Extend +#define _NU 4 // Numpad +#define _FN 5 // Function + +// Some quick aliases, just to make it look pretty +#define _______ KC_TRNS +#define KCX_CA LCTL(KC_LALT) +#define KCX_CS LCTL(KC_LSFT) +#define KCX_CSA LCTL(LSFT(KC_LALT)) +#define KCX_LST LSFT(KC_TAB) +#define KX_COPY LCTL(KC_C) +#define KX_CUT LCTL(KC_X) +#define KX_PAST LCTL(KC_V) +#define KX_UNDO LCTL(KC_Z) + +#define _USER 0 // User macro + +; // This doesn't do anything. It's just for VSCode because its syntax highlighting is weird for the above #define statements. + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* + * Colemak-ModDH + * + * ,----------------------------------. ,----------------------------------. + * | Q | W | F | P | B | | J | L | U | Y | ; | + * +------+------+------+------+------| +------+------+------+------+------| + * | A | R | S | T | G | | M | N | E | I | O | + * +------+------+------+------+------| +------+------+------+------+------| + * |Z Shft| X | C | D | V | ,------. ,------. | K | H | , | . |/ Shft| + * +------+------+------+------+------| | Ctrl | | Alt | +------+------+------+------+------| + * | Esc | Gui | Tab | _FN | Bksp | | Del | | Enter| |Sp/_NU| _EX | - | ' | = | + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_CO] = KEYMAP( + KC_Q, KC_W, KC_F, KC_P, KC_B, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, + KC_A, KC_R, KC_S, KC_T, KC_G, KC_M, KC_N, KC_E, KC_I, KC_O, + SFT_T(KC_Z), KC_X, KC_C, KC_D, KC_V, KC_K, KC_H, KC_COMM, KC_DOT, SFT_T(KC_SLSH), + KC_ESC, KC_LGUI, KC_TAB, MO(_FN), KC_BSPC, CTL_T(KC_DEL), ALT_T(KC_ENT), LT(_NU, KC_SPC), MO(_EX), KC_MINS, KC_QUOT, KC_EQL +), + +/* + * QWERTY + * + * ,----------------------------------. ,----------------------------------. + * | Q | W | E | R | T | | Y | U | I | O | P | + * +------+------+------+------+------| +------+------+------+------+------| + * | A | S | D | F | G | | H | J | K | L | ; | + * +------+------+------+------+------| +------+------+------+------+------| + * |Z Shft| X | C | V | B | ,------. ,------. | N | M | , | . |/ Shft| + * +------+------+------+------+------| | Ctrl | | Alt | +------+------+------+------+------| + * | Esc | Gui | Tab | _FN | Bksp | | Del | | Enter| |Sp/_NU| _EX | - | ' | = | + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_QW] = KEYMAP( /* Qwerty */ + KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, + KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, + SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH), + KC_ESC, KC_LGUI, KC_TAB, MO(_FN), KC_BSPC, CTL_T(KC_DEL), ALT_T(KC_ENT), LT(_NU, KC_SPC), MO(_EX), KC_MINS, KC_QUOT, KC_EQL +), + +/* + * Extend + * + * Ctrl+` is a keyboard shortcut for the program ConEmu, which brings up a dropdown console window. + * + * Also note that some dual-role keys are overridden here with their modifiers + * + * ,----------------------------------. ,----------------------------------. + * | | | | |Ctrl `| | PgUp | Home | Up | End | Del | + * +------+------+------+------+------| +------+------+------+------+------| + * | Gui | Shift| Alt | Ctrl | | | PgDn | Left | Down | Right| Bksp | + * +------+------+------+------+------| +------+------+------+------+------| + * | Shift| Cut | Copy | | Paste| ,------. ,------. | | ^Tab | Tab | |Insert| + * +------+------+------+------+------| | Del | | Enter| +------+------+------+------+------| + * | | | | | | | | | | | Space|XXXXXX| | |PrntSc| + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_EX] = KEYMAP( /* Extend */ + _______, _______, _______, _______, LCTL(KC_GRV), KC_PGUP, KC_HOME, KC_UP, KC_END, KC_DEL, + KC_LGUI, KC_LSFT, KC_LALT, KC_LCTL, _______, KC_PGDN, KC_LEFT, KC_DOWN, KC_RGHT, KC_BSPC, + KC_LSFT, KX_CUT, KX_COPY, _______, KX_PAST, _______, KCX_LST, KC_TAB, _______, KC_INS, + _______, _______, _______, _______, _______, KC_DEL, KC_ENT, KC_SPC, _______, _______, _______, KC_PSCR +), + +/* + * Numbers and symbols + * + * ,----------------------------------. ,----------------------------------. + * | ! | @ | { | } | & | | / | 7 | 8 | 9 | * | + * +------+------+------+------+------| +------+------+------+------+------| + * | # | $ | ( | ) | ~ | | | | 4 | 5 | 6 | - | + * +------+------+------+------+------| +------+------+------+------+------| + * | % | ^ | [ | ] | ` | ,------. ,------. | \ | 1 | 2 | 3 | + | + * +------+------+------+------+------| | | | | +------+------+------+------+------| + * | | _GA | | | | | | | | |XXXXXX| 0 | . | = | | + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_NU] = KEYMAP( /* Numbers and symbols */ + KC_EXLM, KC_AT, KC_LCBR, KC_RCBR, KC_AMPR, KC_SLSH, KC_7, KC_8, KC_9, KC_ASTR, + KC_HASH, KC_DLR, KC_LPRN, KC_RPRN, KC_TILD, KC_PIPE, KC_4, KC_5, KC_6, KC_MINS, + KC_PERC, KC_CIRC, KC_LBRC, KC_RBRC, KC_GRV, KC_BSLS, KC_1, KC_2, KC_3, KC_PLUS, + _______, TG(_GA), _______, _______, _______, _______, _______, _______, KC_0, KC_DOT, KC_EQL, _______ +), + +/* + * Functions + * + * ,----------------------------------. ,----------------------------------. + * | Caps | F9 | F10 | F11 | F12 | | _USER|Whl Up| MUp |Whl Dn| | + * +------+------+------+------+------| +------+------+------+------+------| + * | | F5 | F6 | F7 | F8 | | Vol ^| MLeft| MDown|MRight| | + * +------+------+------+------+------| +------+------+------+------+------| + * | | F1 | F2 | F3 | F4 | ,------. ,------. | Vol v| | | | | + * +------+------+------+------+------| | | |RClick| +------+------+------+------+------| + * | | | |XXXXXX| | | | | | |LClick|MClick| _CO | _GA | RESET| + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_FN] = KEYMAP( /* Functions */ + KC_CAPS, KC_F9, KC_F10, KC_F11, KC_F12, M(_USER),KC_WH_U, KC_MS_U, KC_WH_D, _______, + _______, KC_F5, KC_F6, KC_F7, KC_F8, KC_VOLU, KC_MS_L, KC_MS_D, KC_MS_R, _______, + _______, KC_F1, KC_F2, KC_F3, KC_F4, KC_VOLD, _______, _______, _______, _______, + _______, _______, _______, _______, _______, _______, KC_BTN2, KC_BTN1, KC_BTN3, DF(_CO), DF(_QW), RESET +), + +/* + * Gaming + * + * ,----------------------------------. ,----------------------------------. + * | | | | | | | |Whl Up| MUp |Whl Dn| | + * +------+------+------+------+------| +------+------+------+------+------| + * | | | | | | | | MLeft| MDown|MRight| | + * +------+------+------+------+------| +------+------+------+------+------| + * | Z | | | | | ,------. ,------. | | | | | | + * +------+------+------+------+------| | Bksp | |RClick| +------+------+------+------+------| + * | | _GA | | Shift| Space| | | | | |LClick|MClick| | | | + * `----------------------------------' `------' `------' `----------------------------------' + * + */ +[_GA] = KEYMAP( /* Gaming */ + _______, _______, _______, _______, _______, _______, KC_WH_U, KC_MS_U, KC_WH_D, _______, + _______, _______, _______, _______, _______, _______, KC_MS_L, KC_MS_D, KC_MS_R, _______, + KC_Z, _______, _______, _______, _______, _______, _______, KC_MS_D, _______, _______, + _______, TG(_GA), _______, KC_LSFT, KC_SPC, KC_BSPC, KC_BTN2, KC_BTN1, KC_BTN3, _______, _______, _______ +)}; + +/* + * Template + * + * ,----------------------------------. ,----------------------------------. + * | | | | | | | | | | | | + * +------+------+------+------+------| +------+------+------+------+------| + * | | | | | | | | | | | | + * +------+------+------+------+------| +------+------+------+------+------| + * | | | | | | ,------. ,------. | | | | | | + * +------+------+------+------+------| | | | | +------+------+------+------+------| + * | | | | | | | | | | | | | | | | + * `----------------------------------' `------' `------' `----------------------------------' + * + */ + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case _USER: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/atreus/keymaps/replicaJunction/readme.md b/keyboards/atreus/keymaps/replicaJunction/readme.md new file mode 100644 index 000000000..6ac3cb00a --- /dev/null +++ b/keyboards/atreus/keymaps/replicaJunction/readme.md @@ -0,0 +1,61 @@ +# replicaJunction - Atreus Layout # + +This layout is designed to make the absolute most out of the Atreus 40% keyboard. + +I was enchanted with the idea of the Atreus keyboard after using my Ergodox for several months. I wanted something of a similar form factor that was easily portable, so I could bring and transport a keyboard to my workplace without much hassle. After building the Atreus keyboard, though, I realized very quickly that the 40% form factor requires a lot more creativity than a full-size keyboard (even one as strangely-shaped as the Ergodox). + +The default Atreus keyboard layout provides all the necessary keys in order to function with the keyboard, but as a programmer, I needed quicker access to just about everything. I noticed that the default layer didn't include any dual-role keys, and so I started on my journey to build my perfect layout for the Atreus. + +I won't claim that this layout is perfect for everyone. It does make several significant changes from the "normal" Atreus layout. In my own use, though, I've found this keyboard turbocharges my Atreus, and gives it the power of a full-size keyboard without the size. + +## Base Layer ## + + + +The letters on this layout are arranged in the [Colemak Mod-DH layout](https://colemakmods.github.io/mod-dh/). + +The primary mechanism for the Shift keys in this keyboard are the dual-role Z and slash keys. Pressing the key sends the keystroke, while holding the key sends a shift. This is a design choice taken from the xyverz layout, and one I find much more intuitive than a thumb shift. In addition, the pinky doesn't need to stretch as far to reach these keys as it does to reach a standard Shift key. + +Occasionally, when typing the letter Z, I'll hold the key down a fraction of a second too long, and the keyboard will shift instead. If you're not a confident typist, this dual-role Shift key layout is probably not a good solution. In that case, I'd suggest moving Shift onto the Backspace key (press for Backspace, hold for Shift). + +In addition to the Shift keys, there are three dual-purpose keys: Ctrl (Delete), Alt (Enter), and Space (Number layer). In QMK, these dual-role keys can be made to hold their primary key with a tap and hold. For example, if I wanted to insert a long string of Spaces, I would tap the Space key, then tap it again and hold. A single press and hold would trigger the secondary function of the key instead. + +## Extend Layer ## + + + +This layout is designed primarily for keyboard navigation. Arrow keys are easily accessible under the right hand (a welcome change from the original Atreus layout, which places them under the left hand), along with Home/End and PgUp/PgDn. + +Modifiers are also placed under the home row of the left hand. One of the single keyboard actions I use most is Shift+Ctrl+Left/Right to select a whole word; this layer makes those keypresses simple by adding the Ctrl key in an easy-to-reach location. + +For the common Ctrl shortcuts, I also added some hotkeys to this layer over the letter keys they are associated with. This gives the Extend key some extra utility by letting it "feel" like a Ctrl key in some cases. + +The Space key exists to prevent going from this layer directly into the Number layer. Similarly, the Shift key on the left pinky helps make sure that the normal letter (Z) doesn't fire. + +## Number and Symbol Layer ## + + + +This layer provides the only way of accessing number keys on this keyboard, since it's too small for its own number row. Note that even though they are laid out in the number pad fashion, they send the "regular" number keystrokes. Games and programs that specifically use NumPad keys are not supported in this layout at the moment. + +This layer also provides plenty of symbol shortcuts. Most of these can be accessed through other means (like Shift+8 for the asterisk), but having shortcut keys to them makes for one less keypress, which adds up quickly when using these symbols on a regular basis. I've been through many revisions of this concept on my Ergodox as well as the Atreus, and I've finally arrived at this layout as the one that provides the symbols I need most frequently in places I can think to expect them. The Ordinary layout from the Ergodox-EZ keyboard in this repository was a large influence in this design. + +## Function Layer ## + + + +Function keys (F1-F12) are on this layer. Their layout in groups of four comes from Jeremy's Atreus layout in this repository. I'd been using 1-9 in a numpad layout, then adding 10-12 on the side...I suppose it took seeing someone else do it this way for me to realize how much more sense it makes. + +On the right side are mouse keys - cursor left/right/up/down, and scroll up/down. Volume keys are also here, though really only because there was room for them (I'm not entirely happy with their positions). + +Finally, the reset key is on this layer, as well as toggles from Colemak to QWERTY and back. The QWERTY layer is not currently documented, but it is functionally identical to the base layer except for letter positions. + +## Gaming Layer ## + + + +This is a small layer developed to allow some simple gameplay without a mouse. This layer is a toggle (from the Number layer), so it is designed to stay on while in use. + +The keys on the left hand bring Space into the left thumb's reach, as well as overriding the dual-role Shift with its standard function (Z in both QWERTY and in Colemak). This allows easy Shift presses without blocking the Z key, commonly used in games. + +I would probably not consider the Atreus a hard-core gaming keyboard in the first place, and this layout does have the huge problem of blocking access to the number keys, but for more casual games, it plays quite well. I've used it quite a bit on Minecraft, for example, and I'm quite pleased with it.
\ No newline at end of file diff --git a/keyboards/atreus/keymaps/xyverz/keymap.c b/keyboards/atreus/keymaps/xyverz/keymap.c new file mode 100644 index 000000000..b418cc9b5 --- /dev/null +++ b/keyboards/atreus/keymaps/xyverz/keymap.c @@ -0,0 +1,89 @@ +// This is the personal keymap of Ian Sterling (@xyverz). It is based on the keymap by +// Chris Gerber (@gerbercj), with the addition of persistent layers like the Planck and +// Preonic keyboards by Jack Humbert. + +#include "atreus.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _DV 0 +#define _QW 1 +#define _CM 2 +#define _L1 3 +#define _L2 4 + +// Macro name shortcuts +#define DVORAK M(_DV) +#define QWERTY M(_QW) +#define COLEMAK M(_CM) + + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [_DV] = { /* Dvorak */ + {KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_NO, KC_F, KC_G, KC_C, KC_R, KC_L }, + {KC_A, KC_O, KC_E, KC_U, KC_I, KC_NO, KC_D, KC_H, KC_T, KC_N, KC_S }, + {SFT_T(KC_SCLN), KC_Q, KC_J, KC_K, KC_X, CTL_T(KC_DEL), KC_B, KC_M, KC_W, KC_V, SFT_T(KC_Z) }, + {KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_SLSH, KC_EQL} + }, + [_QW] = { /* Qwerty */ + {KC_Q, KC_W, KC_E, KC_R, KC_T, KC_NO, KC_Y, KC_U, KC_I, KC_O, KC_P }, + {KC_A, KC_S, KC_D, KC_F, KC_G, KC_NO, KC_H, KC_J, KC_K, KC_L, KC_SCLN}, + {SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, CTL_T(KC_DEL), KC_N, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH) }, + {KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_QUOT, KC_ENT} + }, + [_CM] = { /* Colemak */ + {KC_Q, KC_W, KC_F, KC_P, KC_G, KC_NO, KC_J, KC_L, KC_U, KC_Y, KC_SCLN}, + {KC_A, KC_R, KC_S, KC_T, KC_D, KC_NO, KC_H, KC_N, KC_E, KC_I, KC_O }, + {SFT_T(KC_Z), KC_X, KC_C, KC_V, KC_B, CTL_T(KC_DEL), KC_K, KC_M, KC_COMM, KC_DOT, SFT_T(KC_SLSH) }, + {KC_ESC, KC_TAB, KC_LGUI, MO(_L2), KC_BSPC, ALT_T(KC_ENT), KC_SPC, MO(_L1), KC_MINS, KC_QUOT, KC_ENT} + }, + [_L1] = { /* LAYER 1 */ + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_NO, KC_6, KC_7, KC_8, KC_9, KC_0 }, + {KC_TAB, KC_INS, KC_UP, KC_DEL, KC_HOME, KC_NO, KC_PGUP, KC_MUTE, KC_VOLD, KC_VOLU, KC_EQL }, + {KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_END, KC_LCTL, KC_PGDN, KC_MPRV, KC_MPLY, KC_MNXT, KC_BSLS}, + {KC_TRNS, KC_GRV, KC_LGUI, KC_TRNS, KC_DEL, KC_LALT, KC_SPC, KC_TRNS, KC_LBRC, KC_RBRC, KC_ENT } + }, + [_L2] = { /* LAYER 2 */ + {KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_NO, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN}, + {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_NO, KC_TRNS, KC_F6, KC_F7, KC_F8, KC_PLUS}, + {KC_TRNS, KC_TRNS, DVORAK, QWERTY, COLEMAK, KC_LCTL, KC_TRNS, KC_F9, KC_F10, KC_F11, KC_F12 }, + {KC_TRNS, KC_TRNS, KC_LGUI, KC_TRNS, KC_BSPC, KC_LALT, KC_SPC, KC_TRNS, LSFT(KC_LBRC), LSFT(KC_RBRC), RESET} + } +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + switch(id) { + case _DV: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_DV); + } + break; + case _QW: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_QW); + } + break; + case _CM: + if (record->event.pressed) { + persistant_default_layer_set(1UL<<_CM); + } + break; + } + return MACRO_NONE; +}; diff --git a/keyboards/atreus/readme.md b/keyboards/atreus/readme.md index 734f58f0f..476d1bce3 100644 --- a/keyboards/atreus/readme.md +++ b/keyboards/atreus/readme.md @@ -88,7 +88,7 @@ We've added shortcuts to make common modifier/tap (mod-tap) mappings more compac ### Remember: These are just aliases -These functions work the same way that their `ACTION_*` functions do - they're just quick aliases. To dig into all of the tmk ACTION_* functions, please see the [TMK documentation](https://github.com/jackhumbert/qmk_firmware/blob/master/tmk_core/doc/keymap.md#2-action). +These functions work the same way that their `ACTION_*` functions do - they're just quick aliases. To dig into all of the tmk ACTION_* functions, please see the [TMK documentation](https://github.com/qmk/qmk_firmware/blob/master/tmk_core/doc/keymap.md#2-action). Instead of using `FNx` when defining `ACTION_*` functions, you can use `F(x)` - the benefit here is being able to use more than 32 function actions (up to 4096), if you happen to need them. @@ -169,18 +169,19 @@ This requires [some hardware changes](https://www.reddit.com/r/MechanicalKeyboar ## Building -Download or clone the whole firmware and navigate to the keyboards/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. +Download or clone the whole firmware and navigate to the keyboards/atreus folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. Depending on which keymap you would like to use, you will have to compile slightly differently. ### Default -To build with the default keymap, simply run `make`. +To build with the default keymap, simply run `make default`. ### Other Keymaps Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` and see keymap document (you can find in top readme.md) and existent keymap files. -To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: + ``` -$ make KEYMAP=[default|jack|<name>] +$ make [default|jack|<name>] ``` Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. diff --git a/keyboards/atreus/rules.mk b/keyboards/atreus/rules.mk new file mode 100644 index 000000000..3a00993bd --- /dev/null +++ b/keyboards/atreus/rules.mk @@ -0,0 +1,82 @@ + + +ifdef TEENSY2 + OPT_DEFS += -DATREUS_TEENSY2 + ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex +else + OPT_DEFS += -DATREUS_ASTAR + OPT_DEFS += -DCATERINA_BOOTLOADER + ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) +endif + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend +NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA +# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +# MIDI_ENABLE ?= YES # MIDI controls +UNICODE_ENABLE ?= YES # Unicode +# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID + +USB ?= /dev/cu.usbmodem1411 + +upload: build + $(ATREUS_UPLOAD_COMMAND) |
