summaryrefslogtreecommitdiffstats
path: root/keyboards/chibios_test/stm32_f103_onekey
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/chibios_test/stm32_f103_onekey')
-rw-r--r--keyboards/chibios_test/stm32_f103_onekey/Makefile53
-rw-r--r--keyboards/chibios_test/stm32_f103_onekey/mcuconf.h418
-rw-r--r--keyboards/chibios_test/stm32_f103_onekey/rules.mk52
3 files changed, 263 insertions, 260 deletions
diff --git a/keyboards/chibios_test/stm32_f103_onekey/Makefile b/keyboards/chibios_test/stm32_f103_onekey/Makefile
index 307ca5b19..191c6bb66 100644
--- a/keyboards/chibios_test/stm32_f103_onekey/Makefile
+++ b/keyboards/chibios_test/stm32_f103_onekey/Makefile
@@ -1,52 +1,3 @@
-# project specific files
-SRC = matrix.c \
- led.c
-
-# GENERIC STM32F103C8T6 board - stm32duino bootloader
-OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
-MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
-BOARD = GENERIC_STM32_F103
-
-# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
-# OPT_DEFS =
-# MCU_LDSCRIPT = STM32F103x8
-# BOARD = GENERIC_STM32_F103
-
-# MAPLE MINI
-# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
-# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
-# BOARD = MAPLEMINI_STM32_F103
-
-## chip/board settings
-# the next two should match the directories in
-# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
-MCU_FAMILY = STM32
-MCU_SERIES = STM32F1xx
-# linker script to use
-# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
-# or <this_dir>/ld/
-# startup code to use
-# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
-MCU_STARTUP = stm32f1xx
-# it should exist either in <chibios>/os/hal/boards/
-# or <this_dir>/boards
-# Cortex version
-# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
-MCU = cortex-m3
-# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
-ARMV = 7
-# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
-# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
-# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
-# a custom board definition that you plan to reuse).
-# If you're not setting it here, leave it commented out.
-# It is chip dependent, the correct number can be looked up here (page 175):
-# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
-# This also requires a patch to chibios:
-# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
-#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
-
-
-ifndef QUANTUM_DIR
+ifndef MAKEFILE_INCLUDED
include ../../../Makefile
-endif
+endif \ No newline at end of file
diff --git a/keyboards/chibios_test/stm32_f103_onekey/mcuconf.h b/keyboards/chibios_test/stm32_f103_onekey/mcuconf.h
index 626332a6a..276829216 100644
--- a/keyboards/chibios_test/stm32_f103_onekey/mcuconf.h
+++ b/keyboards/chibios_test/stm32_f103_onekey/mcuconf.h
@@ -1,209 +1,209 @@
-/*
- ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#ifndef _MCUCONF_H_
-#define _MCUCONF_H_
-
-#define STM32F103_MCUCONF
-
-/*
- * STM32F103 drivers configuration.
- * The following settings override the default settings present in
- * the various device driver implementation headers.
- * Note that the settings for each driver only have effect if the whole
- * driver is enabled in halconf.h.
- *
- * IRQ priorities:
- * 15...0 Lowest...Highest.
- *
- * DMA priorities:
- * 0...3 Lowest...Highest.
- */
-
-/*
- * HAL driver system settings.
- */
-#define STM32_NO_INIT FALSE
-#define STM32_HSI_ENABLED TRUE
-#define STM32_LSI_ENABLED FALSE
-#define STM32_HSE_ENABLED TRUE
-#define STM32_LSE_ENABLED FALSE
-#define STM32_SW STM32_SW_PLL
-#define STM32_PLLSRC STM32_PLLSRC_HSE
-#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1
-#define STM32_PLLMUL_VALUE 9
-#define STM32_HPRE STM32_HPRE_DIV1
-#define STM32_PPRE1 STM32_PPRE1_DIV2
-#define STM32_PPRE2 STM32_PPRE2_DIV2
-#define STM32_ADCPRE STM32_ADCPRE_DIV4
-#define STM32_USB_CLOCK_REQUIRED TRUE
-#define STM32_USBPRE STM32_USBPRE_DIV1P5
-#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
-#define STM32_RTCSEL STM32_RTCSEL_HSEDIV
-#define STM32_PVD_ENABLE FALSE
-#define STM32_PLS STM32_PLS_LEV0
-
-/*
- * ADC driver system settings.
- */
-#define STM32_ADC_USE_ADC1 FALSE
-#define STM32_ADC_ADC1_DMA_PRIORITY 2
-#define STM32_ADC_ADC1_IRQ_PRIORITY 6
-
-/*
- * CAN driver system settings.
- */
-#define STM32_CAN_USE_CAN1 FALSE
-#define STM32_CAN_CAN1_IRQ_PRIORITY 11
-
-/*
- * EXT driver system settings.
- */
-#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI17_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
-#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
-
-/*
- * GPT driver system settings.
- */
-#define STM32_GPT_USE_TIM1 FALSE
-#define STM32_GPT_USE_TIM2 FALSE
-#define STM32_GPT_USE_TIM3 FALSE
-#define STM32_GPT_USE_TIM4 FALSE
-#define STM32_GPT_USE_TIM5 FALSE
-#define STM32_GPT_USE_TIM8 FALSE
-#define STM32_GPT_TIM1_IRQ_PRIORITY 7
-#define STM32_GPT_TIM2_IRQ_PRIORITY 7
-#define STM32_GPT_TIM3_IRQ_PRIORITY 7
-#define STM32_GPT_TIM4_IRQ_PRIORITY 7
-#define STM32_GPT_TIM5_IRQ_PRIORITY 7
-#define STM32_GPT_TIM8_IRQ_PRIORITY 7
-
-/*
- * I2C driver system settings.
- */
-#define STM32_I2C_USE_I2C1 FALSE
-#define STM32_I2C_USE_I2C2 FALSE
-#define STM32_I2C_BUSY_TIMEOUT 50
-#define STM32_I2C_I2C1_IRQ_PRIORITY 5
-#define STM32_I2C_I2C2_IRQ_PRIORITY 5
-#define STM32_I2C_I2C1_DMA_PRIORITY 3
-#define STM32_I2C_I2C2_DMA_PRIORITY 3
-#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
-
-/*
- * ICU driver system settings.
- */
-#define STM32_ICU_USE_TIM1 FALSE
-#define STM32_ICU_USE_TIM2 FALSE
-#define STM32_ICU_USE_TIM3 FALSE
-#define STM32_ICU_USE_TIM4 FALSE
-#define STM32_ICU_USE_TIM5 FALSE
-#define STM32_ICU_USE_TIM8 FALSE
-#define STM32_ICU_TIM1_IRQ_PRIORITY 7
-#define STM32_ICU_TIM2_IRQ_PRIORITY 7
-#define STM32_ICU_TIM3_IRQ_PRIORITY 7
-#define STM32_ICU_TIM4_IRQ_PRIORITY 7
-#define STM32_ICU_TIM5_IRQ_PRIORITY 7
-#define STM32_ICU_TIM8_IRQ_PRIORITY 7
-
-/*
- * PWM driver system settings.
- */
-#define STM32_PWM_USE_ADVANCED FALSE
-#define STM32_PWM_USE_TIM1 FALSE
-#define STM32_PWM_USE_TIM2 FALSE
-#define STM32_PWM_USE_TIM3 FALSE
-#define STM32_PWM_USE_TIM4 FALSE
-#define STM32_PWM_USE_TIM5 FALSE
-#define STM32_PWM_USE_TIM8 FALSE
-#define STM32_PWM_TIM1_IRQ_PRIORITY 7
-#define STM32_PWM_TIM2_IRQ_PRIORITY 7
-#define STM32_PWM_TIM3_IRQ_PRIORITY 7
-#define STM32_PWM_TIM4_IRQ_PRIORITY 7
-#define STM32_PWM_TIM5_IRQ_PRIORITY 7
-#define STM32_PWM_TIM8_IRQ_PRIORITY 7
-
-/*
- * RTC driver system settings.
- */
-#define STM32_RTC_IRQ_PRIORITY 15
-
-/*
- * SERIAL driver system settings.
- */
-#define STM32_SERIAL_USE_USART1 FALSE
-#define STM32_SERIAL_USE_USART2 FALSE
-#define STM32_SERIAL_USE_USART3 FALSE
-#define STM32_SERIAL_USE_UART4 FALSE
-#define STM32_SERIAL_USE_UART5 FALSE
-#define STM32_SERIAL_USART1_PRIORITY 12
-#define STM32_SERIAL_USART2_PRIORITY 12
-#define STM32_SERIAL_USART3_PRIORITY 12
-#define STM32_SERIAL_UART4_PRIORITY 12
-#define STM32_SERIAL_UART5_PRIORITY 12
-
-/*
- * SPI driver system settings.
- */
-#define STM32_SPI_USE_SPI1 FALSE
-#define STM32_SPI_USE_SPI2 FALSE
-#define STM32_SPI_USE_SPI3 FALSE
-#define STM32_SPI_SPI1_DMA_PRIORITY 1
-#define STM32_SPI_SPI2_DMA_PRIORITY 1
-#define STM32_SPI_SPI3_DMA_PRIORITY 1
-#define STM32_SPI_SPI1_IRQ_PRIORITY 10
-#define STM32_SPI_SPI2_IRQ_PRIORITY 10
-#define STM32_SPI_SPI3_IRQ_PRIORITY 10
-#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
-
-/*
- * ST driver system settings.
- */
-#define STM32_ST_IRQ_PRIORITY 8
-#define STM32_ST_USE_TIMER 2
-
-/*
- * UART driver system settings.
- */
-#define STM32_UART_USE_USART1 FALSE
-#define STM32_UART_USE_USART2 FALSE
-#define STM32_UART_USE_USART3 FALSE
-#define STM32_UART_USART1_IRQ_PRIORITY 12
-#define STM32_UART_USART2_IRQ_PRIORITY 12
-#define STM32_UART_USART3_IRQ_PRIORITY 12
-#define STM32_UART_USART1_DMA_PRIORITY 0
-#define STM32_UART_USART2_DMA_PRIORITY 0
-#define STM32_UART_USART3_DMA_PRIORITY 0
-#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
-
-/*
- * USB driver system settings.
- */
-#define STM32_USB_USE_USB1 TRUE
-#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
-#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
-#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
-
-#endif /* _MCUCONF_H_ */
+/*
+ ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+ Licensed under the Apache License, Version 2.0 (the "License");
+ you may not use this file except in compliance with the License.
+ You may obtain a copy of the License at
+
+ http://www.apache.org/licenses/LICENSE-2.0
+
+ Unless required by applicable law or agreed to in writing, software
+ distributed under the License is distributed on an "AS IS" BASIS,
+ WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ See the License for the specific language governing permissions and
+ limitations under the License.
+*/
+
+#ifndef _MCUCONF_H_
+#define _MCUCONF_H_
+
+#define STM32F103_MCUCONF
+
+/*
+ * STM32F103 drivers configuration.
+ * The following settings override the default settings present in
+ * the various device driver implementation headers.
+ * Note that the settings for each driver only have effect if the whole
+ * driver is enabled in halconf.h.
+ *
+ * IRQ priorities:
+ * 15...0 Lowest...Highest.
+ *
+ * DMA priorities:
+ * 0...3 Lowest...Highest.
+ */
+
+/*
+ * HAL driver system settings.
+ */
+#define STM32_NO_INIT FALSE
+#define STM32_HSI_ENABLED TRUE
+#define STM32_LSI_ENABLED FALSE
+#define STM32_HSE_ENABLED TRUE
+#define STM32_LSE_ENABLED FALSE
+#define STM32_SW STM32_SW_PLL
+#define STM32_PLLSRC STM32_PLLSRC_HSE
+#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1
+#define STM32_PLLMUL_VALUE 9
+#define STM32_HPRE STM32_HPRE_DIV1
+#define STM32_PPRE1 STM32_PPRE1_DIV2
+#define STM32_PPRE2 STM32_PPRE2_DIV2
+#define STM32_ADCPRE STM32_ADCPRE_DIV4
+#define STM32_USB_CLOCK_REQUIRED TRUE
+#define STM32_USBPRE STM32_USBPRE_DIV1P5
+#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK
+#define STM32_RTCSEL STM32_RTCSEL_HSEDIV
+#define STM32_PVD_ENABLE FALSE
+#define STM32_PLS STM32_PLS_LEV0
+
+/*
+ * ADC driver system settings.
+ */
+#define STM32_ADC_USE_ADC1 FALSE
+#define STM32_ADC_ADC1_DMA_PRIORITY 2
+#define STM32_ADC_ADC1_IRQ_PRIORITY 6
+
+/*
+ * CAN driver system settings.
+ */
+#define STM32_CAN_USE_CAN1 FALSE
+#define STM32_CAN_CAN1_IRQ_PRIORITY 11
+
+/*
+ * EXT driver system settings.
+ */
+#define STM32_EXT_EXTI0_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI1_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI2_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI3_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI4_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI16_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI17_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI18_IRQ_PRIORITY 6
+#define STM32_EXT_EXTI19_IRQ_PRIORITY 6
+
+/*
+ * GPT driver system settings.
+ */
+#define STM32_GPT_USE_TIM1 FALSE
+#define STM32_GPT_USE_TIM2 FALSE
+#define STM32_GPT_USE_TIM3 FALSE
+#define STM32_GPT_USE_TIM4 FALSE
+#define STM32_GPT_USE_TIM5 FALSE
+#define STM32_GPT_USE_TIM8 FALSE
+#define STM32_GPT_TIM1_IRQ_PRIORITY 7
+#define STM32_GPT_TIM2_IRQ_PRIORITY 7
+#define STM32_GPT_TIM3_IRQ_PRIORITY 7
+#define STM32_GPT_TIM4_IRQ_PRIORITY 7
+#define STM32_GPT_TIM5_IRQ_PRIORITY 7
+#define STM32_GPT_TIM8_IRQ_PRIORITY 7
+
+/*
+ * I2C driver system settings.
+ */
+#define STM32_I2C_USE_I2C1 FALSE
+#define STM32_I2C_USE_I2C2 FALSE
+#define STM32_I2C_BUSY_TIMEOUT 50
+#define STM32_I2C_I2C1_IRQ_PRIORITY 5
+#define STM32_I2C_I2C2_IRQ_PRIORITY 5
+#define STM32_I2C_I2C1_DMA_PRIORITY 3
+#define STM32_I2C_I2C2_DMA_PRIORITY 3
+#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure")
+
+/*
+ * ICU driver system settings.
+ */
+#define STM32_ICU_USE_TIM1 FALSE
+#define STM32_ICU_USE_TIM2 FALSE
+#define STM32_ICU_USE_TIM3 FALSE
+#define STM32_ICU_USE_TIM4 FALSE
+#define STM32_ICU_USE_TIM5 FALSE
+#define STM32_ICU_USE_TIM8 FALSE
+#define STM32_ICU_TIM1_IRQ_PRIORITY 7
+#define STM32_ICU_TIM2_IRQ_PRIORITY 7
+#define STM32_ICU_TIM3_IRQ_PRIORITY 7
+#define STM32_ICU_TIM4_IRQ_PRIORITY 7
+#define STM32_ICU_TIM5_IRQ_PRIORITY 7
+#define STM32_ICU_TIM8_IRQ_PRIORITY 7
+
+/*
+ * PWM driver system settings.
+ */
+#define STM32_PWM_USE_ADVANCED FALSE
+#define STM32_PWM_USE_TIM1 FALSE
+#define STM32_PWM_USE_TIM2 FALSE
+#define STM32_PWM_USE_TIM3 FALSE
+#define STM32_PWM_USE_TIM4 FALSE
+#define STM32_PWM_USE_TIM5 FALSE
+#define STM32_PWM_USE_TIM8 FALSE
+#define STM32_PWM_TIM1_IRQ_PRIORITY 7
+#define STM32_PWM_TIM2_IRQ_PRIORITY 7
+#define STM32_PWM_TIM3_IRQ_PRIORITY 7
+#define STM32_PWM_TIM4_IRQ_PRIORITY 7
+#define STM32_PWM_TIM5_IRQ_PRIORITY 7
+#define STM32_PWM_TIM8_IRQ_PRIORITY 7
+
+/*
+ * RTC driver system settings.
+ */
+#define STM32_RTC_IRQ_PRIORITY 15
+
+/*
+ * SERIAL driver system settings.
+ */
+#define STM32_SERIAL_USE_USART1 FALSE
+#define STM32_SERIAL_USE_USART2 FALSE
+#define STM32_SERIAL_USE_USART3 FALSE
+#define STM32_SERIAL_USE_UART4 FALSE
+#define STM32_SERIAL_USE_UART5 FALSE
+#define STM32_SERIAL_USART1_PRIORITY 12
+#define STM32_SERIAL_USART2_PRIORITY 12
+#define STM32_SERIAL_USART3_PRIORITY 12
+#define STM32_SERIAL_UART4_PRIORITY 12
+#define STM32_SERIAL_UART5_PRIORITY 12
+
+/*
+ * SPI driver system settings.
+ */
+#define STM32_SPI_USE_SPI1 FALSE
+#define STM32_SPI_USE_SPI2 FALSE
+#define STM32_SPI_USE_SPI3 FALSE
+#define STM32_SPI_SPI1_DMA_PRIORITY 1
+#define STM32_SPI_SPI2_DMA_PRIORITY 1
+#define STM32_SPI_SPI3_DMA_PRIORITY 1
+#define STM32_SPI_SPI1_IRQ_PRIORITY 10
+#define STM32_SPI_SPI2_IRQ_PRIORITY 10
+#define STM32_SPI_SPI3_IRQ_PRIORITY 10
+#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure")
+
+/*
+ * ST driver system settings.
+ */
+#define STM32_ST_IRQ_PRIORITY 8
+#define STM32_ST_USE_TIMER 2
+
+/*
+ * UART driver system settings.
+ */
+#define STM32_UART_USE_USART1 FALSE
+#define STM32_UART_USE_USART2 FALSE
+#define STM32_UART_USE_USART3 FALSE
+#define STM32_UART_USART1_IRQ_PRIORITY 12
+#define STM32_UART_USART2_IRQ_PRIORITY 12
+#define STM32_UART_USART3_IRQ_PRIORITY 12
+#define STM32_UART_USART1_DMA_PRIORITY 0
+#define STM32_UART_USART2_DMA_PRIORITY 0
+#define STM32_UART_USART3_DMA_PRIORITY 0
+#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure")
+
+/*
+ * USB driver system settings.
+ */
+#define STM32_USB_USE_USB1 TRUE
+#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE
+#define STM32_USB_USB1_HP_IRQ_PRIORITY 13
+#define STM32_USB_USB1_LP_IRQ_PRIORITY 14
+
+#endif /* _MCUCONF_H_ */
diff --git a/keyboards/chibios_test/stm32_f103_onekey/rules.mk b/keyboards/chibios_test/stm32_f103_onekey/rules.mk
new file mode 100644
index 000000000..307ca5b19
--- /dev/null
+++ b/keyboards/chibios_test/stm32_f103_onekey/rules.mk
@@ -0,0 +1,52 @@
+# project specific files
+SRC = matrix.c \
+ led.c
+
+# GENERIC STM32F103C8T6 board - stm32duino bootloader
+OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
+MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
+BOARD = GENERIC_STM32_F103
+
+# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
+# OPT_DEFS =
+# MCU_LDSCRIPT = STM32F103x8
+# BOARD = GENERIC_STM32_F103
+
+# MAPLE MINI
+# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
+# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
+# BOARD = MAPLEMINI_STM32_F103
+
+## chip/board settings
+# the next two should match the directories in
+# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
+MCU_FAMILY = STM32
+MCU_SERIES = STM32F1xx
+# linker script to use
+# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
+# or <this_dir>/ld/
+# startup code to use
+# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
+MCU_STARTUP = stm32f1xx
+# it should exist either in <chibios>/os/hal/boards/
+# or <this_dir>/boards
+# Cortex version
+# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
+MCU = cortex-m3
+# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
+ARMV = 7
+# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
+# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
+# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
+# a custom board definition that you plan to reuse).
+# If you're not setting it here, leave it commented out.
+# It is chip dependent, the correct number can be looked up here (page 175):
+# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
+# This also requires a patch to chibios:
+# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
+#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
+
+
+ifndef QUANTUM_DIR
+ include ../../../Makefile
+endif
generated by cgit v1.2.3-24-g4f1b (git 2.32.0) at 2024-07-04 15:26:37 +0200