diff options
Diffstat (limited to 'keyboards/clueboard2')
| -rw-r--r-- | keyboards/clueboard2/Makefile | 71 | ||||
| -rw-r--r-- | keyboards/clueboard2/clueboard2.c | 63 |
2 files changed, 134 insertions, 0 deletions
diff --git a/keyboards/clueboard2/Makefile b/keyboards/clueboard2/Makefile new file mode 100644 index 000000000..e9367a90d --- /dev/null +++ b/keyboards/clueboard2/Makefile @@ -0,0 +1,71 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE ?= no # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID + +ifndef QUANTUM_DIR + include ../../Makefile +endif diff --git a/keyboards/clueboard2/clueboard2.c b/keyboards/clueboard2/clueboard2.c new file mode 100644 index 000000000..d78ffed9b --- /dev/null +++ b/keyboards/clueboard2/clueboard2.c @@ -0,0 +1,63 @@ +#include "clueboard2.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); + + // JTAG disable for PORT F. write JTD bit twice within four cycles. + MCUCR |= (1<<JTD); + MCUCR |= (1<<JTD); +}; + +void led_init_ports() { + // * Set our LED pins as output + DDRB |= (1<<4); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + // Turn capslock on + PORTB |= (1<<4); + } else { + // Turn capslock off + PORTB &= ~(1<<4); + } +} + +/* Clueboard 2.0 LED locations: + * + * Capslock: B4, pull high to turn on + * LCtrl: Shared with Capslock, DO NOT INSTALL LED'S IN BOTH + * Page Up: B7, pull high to turn on + * Escape: D6, pull high to turn on + * Arrows: D4, pull high to turn on + */ + +void backlight_init_ports(void) { + print("init_backlight_pin()\n"); + // Set our LED pins as output + DDRD |= (1<<6); // Esc + DDRB |= (1<<7); // Page Up + DDRD |= (1<<4); // Arrows + + // Set our LED pins low + PORTD &= ~(1<<6); // Esc + PORTB &= ~(1<<7); // Page Up + PORTD &= ~(1<<4); // Arrows +} + +void backlight_set(uint8_t level) { + if ( level == 0 ) { + // Turn off light + PORTD |= (1<<6); // Esc + PORTB |= (1<<7); // Page Up + PORTD |= (1<<4); // Arrows + } else { + // Turn on light + PORTD &= ~(1<<6); // Esc + PORTB &= ~(1<<7); // Page Up + PORTD &= ~(1<<4); // Arrows + } +} |