diff options
Diffstat (limited to 'keyboards/converter/usb_usb/rules.mk')
| -rw-r--r-- | keyboards/converter/usb_usb/rules.mk | 149 |
1 files changed, 149 insertions, 0 deletions
diff --git a/keyboards/converter/usb_usb/rules.mk b/keyboards/converter/usb_usb/rules.mk new file mode 100644 index 000000000..2d1f284b9 --- /dev/null +++ b/keyboards/converter/usb_usb/rules.mk @@ -0,0 +1,149 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET ?= usb_usb + +TMK_DIR ?= ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR ?= . + +# MCU name +MCU ?= atmega32u4 + + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU ?= 8000000 + + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH ?= AVR8 +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB ?= $(F_CPU) +# Interrupt driven control endpoint task +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + + +# Build Options +# comment out to disable the options. +# +#MOUSEKEY_ENABLE ?= yes # Mouse keys +EXTRAKEY_ENABLE ?= yes # Media control and System control +CONSOLE_ENABLE ?= yes # Console for debug +#COMMAND_ENABLE ?= yes # Commands for debug and configuration +#NKRO_ENABLE ?= yes # USB Nkey Rollover + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +#LDFLAGS += -Wl,--relax + +#OPT_DEFS += -DNO_ACTION_TAPPING +#OPT_DEFS += -DNO_ACTION_LAYER +#OPT_DEFS += -DNO_ACTION_MACRO + +SRC = matrix.cpp + +# +# Keymap file +# +# ifeq (yes,$(strip $(UNIMAP_ENABLE))) +# KEYMAP_FILE = unimap +# else +# ifeq (yes,$(strip $(ACTIONMAP_ENABLE))) +# KEYMAP_FILE = actionmap +# else +# KEYMAP_FILE = keymap +# endif +# endif +# ifdef KEYMAP +# SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) +# else +# SRC := $(KEYMAP_FILE).c $(SRC) +# endif + +# CONFIG_H ?= config.h + + + +# Search Path +# VPATH += $(TARGET_DIR) +# VPATH += $(TMK_DIR) + + + +# program Leonardo +# PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV) + + + +include $(TMK_DIR)/protocol/usb_hid.mk +include $(TMK_DIR)/protocol/lufa.mk +# include $(TMK_DIR)/common.mk +# include $(TMK_DIR)/rules.mk |