diff options
Diffstat (limited to 'keyboards/hotdox/rules.mk')
| -rw-r--r-- | keyboards/hotdox/rules.mk | 82 |
1 files changed, 82 insertions, 0 deletions
diff --git a/keyboards/hotdox/rules.mk b/keyboards/hotdox/rules.mk new file mode 100644 index 000000000..f785cdd06 --- /dev/null +++ b/keyboards/hotdox/rules.mk @@ -0,0 +1,82 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make = Make software. +# +# make clean = Clean out built project files. +# +# That's pretty much all you need. To compile, always go make clean, +# followed by make. +# +# For advanced users only: +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +#---------------------------------------------------------------------------- + +# # project specific files +SRC = matrix.c \ + i2c_master.c \ + left.c + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Boot Section +BOOTLOADER = atmel-dfu + +# Build Options +# comment out to disable the options. +# +CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDone +UNICODE_ENABLE = yes # Unicode +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA +USB_6KRO_ENABLE = no # USB 6key Rollover +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor +SWAP_HANDS_ENABLE = no # Disable Onehand +RGBLIGHT_ENABLE = no +MIDI_ENABLE = no + +LAYOUTS = ergodox |