diff options
Diffstat (limited to 'keyboards/lets_split')
| -rw-r--r-- | keyboards/lets_split/Makefile | 77 | ||||
| -rw-r--r-- | keyboards/lets_split/pro_micro.h | 64 | ||||
| -rw-r--r-- | keyboards/lets_split/rules.mk | 74 |
3 files changed, 107 insertions, 108 deletions
diff --git a/keyboards/lets_split/Makefile b/keyboards/lets_split/Makefile index b9f07636b..4e2a6f00f 100644 --- a/keyboards/lets_split/Makefile +++ b/keyboards/lets_split/Makefile @@ -1,78 +1,3 @@ -SRC += matrix.c \ - i2c.c \ - split_util.c \ - serial.c - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= no # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality -MIDI_ENABLE ?= no # MIDI controls -AUDIO_ENABLE ?= yes # Audio output on port C6 -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. - -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend - -CUSTOM_MATRIX = yes - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif
\ No newline at end of file diff --git a/keyboards/lets_split/pro_micro.h b/keyboards/lets_split/pro_micro.h index 09e219b7b..f9e7ed75d 100644 --- a/keyboards/lets_split/pro_micro.h +++ b/keyboards/lets_split/pro_micro.h @@ -111,18 +111,18 @@ static const uint8_t SCK = 15; // Mapping of analog pins as digital I/O // A6-A11 share with digital pins -static const uint8_t A0 = 18; -static const uint8_t A1 = 19; -static const uint8_t A2 = 20; -static const uint8_t A3 = 21; -static const uint8_t A4 = 22; -static const uint8_t A5 = 23; -static const uint8_t A6 = 24; // D4 -static const uint8_t A7 = 25; // D6 -static const uint8_t A8 = 26; // D8 -static const uint8_t A9 = 27; // D9 -static const uint8_t A10 = 28; // D10 -static const uint8_t A11 = 29; // D12 +static const uint8_t ADC0 = 18; +static const uint8_t ADC1 = 19; +static const uint8_t ADC2 = 20; +static const uint8_t ADC3 = 21; +static const uint8_t ADC4 = 22; +static const uint8_t ADC5 = 23; +static const uint8_t ADC6 = 24; // D4 +static const uint8_t ADC7 = 25; // D6 +static const uint8_t ADC8 = 26; // D8 +static const uint8_t ADC9 = 27; // D9 +static const uint8_t ADC10 = 28; // D10 +static const uint8_t ADC11 = 29; // D12 #define digitalPinToPCICR(p) ((((p) >= 8 && (p) <= 11) || ((p) >= 14 && (p) <= 17) || ((p) >= A8 && (p) <= A10)) ? (&PCICR) : ((uint8_t *)0)) #define digitalPinToPCICRbit(p) 0 @@ -220,26 +220,26 @@ const uint8_t PROGMEM digital_pin_to_port_PGM[] = { PC, // D5 - PC6 PD, // D6 - PD7 PE, // D7 - PE6 - + PB, // D8 - PB4 PB, // D9 - PB5 PB, // D10 - PB6 PB, // D11 - PB7 PD, // D12 - PD6 PC, // D13 - PC7 - + PB, // D14 - MISO - PB3 PB, // D15 - SCK - PB1 PB, // D16 - MOSI - PB2 PB, // D17 - SS - PB0 - + PF, // D18 - A0 - PF7 PF, // D19 - A1 - PF6 PF, // D20 - A2 - PF5 PF, // D21 - A3 - PF4 PF, // D22 - A4 - PF1 PF, // D23 - A5 - PF0 - + PD, // D24 - PD5 PD, // D25 / D6 - A7 - PD7 PB, // D26 / D8 - A8 - PB4 @@ -257,26 +257,26 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = { _BV(6), // D5 - PC6 _BV(7), // D6 - PD7 _BV(6), // D7 - PE6 - + _BV(4), // D8 - PB4 _BV(5), // D9 - PB5 _BV(6), // D10 - PB6 _BV(7), // D11 - PB7 _BV(6), // D12 - PD6 _BV(7), // D13 - PC7 - + _BV(3), // D14 - MISO - PB3 _BV(1), // D15 - SCK - PB1 _BV(2), // D16 - MOSI - PB2 _BV(0), // D17 - SS - PB0 - + _BV(7), // D18 - A0 - PF7 _BV(6), // D19 - A1 - PF6 _BV(5), // D20 - A2 - PF5 _BV(4), // D21 - A3 - PF4 _BV(1), // D22 - A4 - PF1 _BV(0), // D23 - A5 - PF0 - + _BV(5), // D24 - PD5 _BV(7), // D25 / D6 - A7 - PD7 _BV(4), // D26 / D8 - A8 - PB4 @@ -286,24 +286,24 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = { }; const uint8_t PROGMEM digital_pin_to_timer_PGM[] = { - NOT_ON_TIMER, + NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, TIMER0B, /* 3 */ NOT_ON_TIMER, TIMER3A, /* 5 */ TIMER4D, /* 6 */ - NOT_ON_TIMER, - - NOT_ON_TIMER, + NOT_ON_TIMER, + + NOT_ON_TIMER, TIMER1A, /* 9 */ TIMER1B, /* 10 */ TIMER0A, /* 11 */ - - NOT_ON_TIMER, + + NOT_ON_TIMER, TIMER4A, /* 13 */ - - NOT_ON_TIMER, + + NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, @@ -324,11 +324,11 @@ const uint8_t PROGMEM digital_pin_to_timer_PGM[] = { const uint8_t PROGMEM analog_pin_to_channel_PGM[] = { 7, // A0 PF7 ADC7 - 6, // A1 PF6 ADC6 - 5, // A2 PF5 ADC5 + 6, // A1 PF6 ADC6 + 5, // A2 PF5 ADC5 4, // A3 PF4 ADC4 - 1, // A4 PF1 ADC1 - 0, // A5 PF0 ADC0 + 1, // A4 PF1 ADC1 + 0, // A5 PF0 ADC0 8, // A6 D4 PD4 ADC8 10, // A7 D6 PD7 ADC10 11, // A8 D8 PB4 ADC11 diff --git a/keyboards/lets_split/rules.mk b/keyboards/lets_split/rules.mk new file mode 100644 index 000000000..6961fbd55 --- /dev/null +++ b/keyboards/lets_split/rules.mk @@ -0,0 +1,74 @@ +SRC += matrix.c \ + i2c.c \ + split_util.c \ + serial.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= yes # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +CUSTOM_MATRIX = yes
\ No newline at end of file |