summaryrefslogtreecommitdiffstats
path: root/keyboards/treadstone48/serial.c
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/treadstone48/serial.c')
-rw-r--r--keyboards/treadstone48/serial.c590
1 files changed, 590 insertions, 0 deletions
diff --git a/keyboards/treadstone48/serial.c b/keyboards/treadstone48/serial.c
new file mode 100644
index 000000000..6006ebf1b
--- /dev/null
+++ b/keyboards/treadstone48/serial.c
@@ -0,0 +1,590 @@
+/*
+ * WARNING: be careful changing this code, it is very timing dependent
+ *
+ * 2018-10-28 checked
+ * avr-gcc 4.9.2
+ * avr-gcc 5.4.0
+ * avr-gcc 7.3.0
+ */
+
+#ifndef F_CPU
+#define F_CPU 16000000
+#endif
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <util/delay.h>
+#include <stddef.h>
+#include <stdbool.h>
+#include "serial.h"
+//#include <pro_micro.h>
+
+#ifdef SOFT_SERIAL_PIN
+
+#ifdef __AVR_ATmega32U4__
+ // if using ATmega32U4 I2C, can not use PD0 and PD1 in soft serial.
+ #ifdef USE_I2C
+ #if SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1
+ #error Using ATmega32U4 I2C, so can not use PD0, PD1
+ #endif
+ #endif
+
+ #if SOFT_SERIAL_PIN >= D0 && SOFT_SERIAL_PIN <= D3
+ #define SERIAL_PIN_DDR DDRD
+ #define SERIAL_PIN_PORT PORTD
+ #define SERIAL_PIN_INPUT PIND
+ #if SOFT_SERIAL_PIN == D0
+ #define SERIAL_PIN_MASK _BV(PD0)
+ #define EIMSK_BIT _BV(INT0)
+ #define EICRx_BIT (~(_BV(ISC00) | _BV(ISC01)))
+ #define SERIAL_PIN_INTERRUPT INT0_vect
+ #elif SOFT_SERIAL_PIN == D1
+ #define SERIAL_PIN_MASK _BV(PD1)
+ #define EIMSK_BIT _BV(INT1)
+ #define EICRx_BIT (~(_BV(ISC10) | _BV(ISC11)))
+ #define SERIAL_PIN_INTERRUPT INT1_vect
+ #elif SOFT_SERIAL_PIN == D2
+ #define SERIAL_PIN_MASK _BV(PD2)
+ #define EIMSK_BIT _BV(INT2)
+ #define EICRx_BIT (~(_BV(ISC20) | _BV(ISC21)))
+ #define SERIAL_PIN_INTERRUPT INT2_vect
+ #elif SOFT_SERIAL_PIN == D3
+ #define SERIAL_PIN_MASK _BV(PD3)
+ #define EIMSK_BIT _BV(INT3)
+ #define EICRx_BIT (~(_BV(ISC30) | _BV(ISC31)))
+ #define SERIAL_PIN_INTERRUPT INT3_vect
+ #endif
+ #elif SOFT_SERIAL_PIN == E6
+ #define SERIAL_PIN_DDR DDRE
+ #define SERIAL_PIN_PORT PORTE
+ #define SERIAL_PIN_INPUT PINE
+ #define SERIAL_PIN_MASK _BV(PE6)
+ #define EIMSK_BIT _BV(INT6)
+ #define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
+ #define SERIAL_PIN_INTERRUPT INT6_vect
+ #else
+ #error invalid SOFT_SERIAL_PIN value
+ #endif
+
+#else
+ #error serial.c now support ATmega32U4 only
+#endif
+
+//////////////// for backward compatibility ////////////////////////////////
+#if !defined(SERIAL_USE_SINGLE_TRANSACTION) && !defined(SERIAL_USE_MULTI_TRANSACTION)
+/* --- USE OLD API (compatible with let's split serial.c) */
+ #if SERIAL_SLAVE_BUFFER_LENGTH > 0
+ uint8_t volatile serial_slave_buffer[SERIAL_SLAVE_BUFFER_LENGTH] = {0};
+ #endif
+ #if SERIAL_MASTER_BUFFER_LENGTH > 0
+ uint8_t volatile serial_master_buffer[SERIAL_MASTER_BUFFER_LENGTH] = {0};
+ #endif
+ uint8_t volatile status0 = 0;
+
+SSTD_t transactions[] = {
+ { (uint8_t *)&status0,
+ #if SERIAL_MASTER_BUFFER_LENGTH > 0
+ sizeof(serial_master_buffer), (uint8_t *)serial_master_buffer,
+ #else
+ 0, (uint8_t *)NULL,
+ #endif
+ #if SERIAL_SLAVE_BUFFER_LENGTH > 0
+ sizeof(serial_slave_buffer), (uint8_t *)serial_slave_buffer
+ #else
+ 0, (uint8_t *)NULL,
+ #endif
+ }
+};
+
+void serial_master_init(void)
+{ soft_serial_initiator_init(transactions, TID_LIMIT(transactions)); }
+
+void serial_slave_init(void)
+{ soft_serial_target_init(transactions, TID_LIMIT(transactions)); }
+
+// 0 => no error
+// 1 => slave did not respond
+// 2 => checksum error
+int serial_update_buffers()
+{
+ int result;
+ result = soft_serial_transaction();
+ return result;
+}
+
+#endif // end of OLD API (compatible with let's split serial.c)
+////////////////////////////////////////////////////////////////////////////
+
+#define ALWAYS_INLINE __attribute__((always_inline))
+#define NO_INLINE __attribute__((noinline))
+#define _delay_sub_us(x) __builtin_avr_delay_cycles(x)
+
+// parity check
+#define ODD_PARITY 1
+#define EVEN_PARITY 0
+#define PARITY EVEN_PARITY
+
+#ifdef SERIAL_DELAY
+ // custom setup in config.h
+ // #define TID_SEND_ADJUST 2
+ // #define SERIAL_DELAY 6 // micro sec
+ // #define READ_WRITE_START_ADJUST 30 // cycles
+ // #define READ_WRITE_WIDTH_ADJUST 8 // cycles
+#else
+// ============ Standard setups ============
+
+#ifndef SELECT_SOFT_SERIAL_SPEED
+#define SELECT_SOFT_SERIAL_SPEED 1
+// 0: about 189kbps
+// 1: about 137kbps (default)
+// 2: about 75kbps
+// 3: about 39kbps
+// 4: about 26kbps
+// 5: about 20kbps
+#endif
+
+#if __GNUC__ < 6
+ #define TID_SEND_ADJUST 14
+#else
+ #define TID_SEND_ADJUST 2
+#endif
+
+#if SELECT_SOFT_SERIAL_SPEED == 0
+ // Very High speed
+ #define SERIAL_DELAY 4 // micro sec
+ #if __GNUC__ < 6
+ #define READ_WRITE_START_ADJUST 33 // cycles
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_START_ADJUST 34 // cycles
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 1
+ // High speed
+ #define SERIAL_DELAY 6 // micro sec
+ #if __GNUC__ < 6
+ #define READ_WRITE_START_ADJUST 30 // cycles
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_START_ADJUST 33 // cycles
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 2
+ // Middle speed
+ #define SERIAL_DELAY 12 // micro sec
+ #define READ_WRITE_START_ADJUST 30 // cycles
+ #if __GNUC__ < 6
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 3
+ // Low speed
+ #define SERIAL_DELAY 24 // micro sec
+ #define READ_WRITE_START_ADJUST 30 // cycles
+ #if __GNUC__ < 6
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 4
+ // Very Low speed
+ #define SERIAL_DELAY 36 // micro sec
+ #define READ_WRITE_START_ADJUST 30 // cycles
+ #if __GNUC__ < 6
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#elif SELECT_SOFT_SERIAL_SPEED == 5
+ // Ultra Low speed
+ #define SERIAL_DELAY 48 // micro sec
+ #define READ_WRITE_START_ADJUST 30 // cycles
+ #if __GNUC__ < 6
+ #define READ_WRITE_WIDTH_ADJUST 3 // cycles
+ #else
+ #define READ_WRITE_WIDTH_ADJUST 7 // cycles
+ #endif
+#else
+#error invalid SELECT_SOFT_SERIAL_SPEED value
+#endif /* SELECT_SOFT_SERIAL_SPEED */
+#endif /* SERIAL_DELAY */
+
+#define SERIAL_DELAY_HALF1 (SERIAL_DELAY/2)
+#define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY/2)
+
+#define SLAVE_INT_WIDTH_US 1
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+ #define SLAVE_INT_RESPONSE_TIME SERIAL_DELAY
+#else
+ #define SLAVE_INT_ACK_WIDTH_UNIT 2
+ #define SLAVE_INT_ACK_WIDTH 4
+#endif
+
+static SSTD_t *Transaction_table = NULL;
+static uint8_t Transaction_table_size = 0;
+
+inline static void serial_delay(void) ALWAYS_INLINE;
+inline static
+void serial_delay(void) {
+ _delay_us(SERIAL_DELAY);
+}
+
+inline static void serial_delay_half1(void) ALWAYS_INLINE;
+inline static
+void serial_delay_half1(void) {
+ _delay_us(SERIAL_DELAY_HALF1);
+}
+
+inline static void serial_delay_half2(void) ALWAYS_INLINE;
+inline static
+void serial_delay_half2(void) {
+ _delay_us(SERIAL_DELAY_HALF2);
+}
+
+inline static void serial_output(void) ALWAYS_INLINE;
+inline static
+void serial_output(void) {
+ SERIAL_PIN_DDR |= SERIAL_PIN_MASK;
+}
+
+// make the serial pin an input with pull-up resistor
+inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
+inline static
+void serial_input_with_pullup(void) {
+ SERIAL_PIN_DDR &= ~SERIAL_PIN_MASK;
+ SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
+}
+
+inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
+inline static
+uint8_t serial_read_pin(void) {
+ return !!(SERIAL_PIN_INPUT & SERIAL_PIN_MASK);
+}
+
+inline static void serial_low(void) ALWAYS_INLINE;
+inline static
+void serial_low(void) {
+ SERIAL_PIN_PORT &= ~SERIAL_PIN_MASK;
+}
+
+inline static void serial_high(void) ALWAYS_INLINE;
+inline static
+void serial_high(void) {
+ SERIAL_PIN_PORT |= SERIAL_PIN_MASK;
+}
+
+void soft_serial_initiator_init(SSTD_t *sstd_table, int sstd_table_size)
+{
+ Transaction_table = sstd_table;
+ Transaction_table_size = (uint8_t)sstd_table_size;
+ serial_output();
+ serial_high();
+}
+
+void soft_serial_target_init(SSTD_t *sstd_table, int sstd_table_size)
+{
+ Transaction_table = sstd_table;
+ Transaction_table_size = (uint8_t)sstd_table_size;
+ serial_input_with_pullup();
+
+ // Enable INT0-INT3,INT6
+ EIMSK |= EIMSK_BIT;
+#if SERIAL_PIN_MASK == _BV(PE6)
+ // Trigger on falling edge of INT6
+ EICRB &= EICRx_BIT;
+#else
+ // Trigger on falling edge of INT0-INT3
+ EICRA &= EICRx_BIT;
+#endif
+}
+
+// Used by the sender to synchronize timing with the reciver.
+static void sync_recv(void) NO_INLINE;
+static
+void sync_recv(void) {
+ for (uint8_t i = 0; i < SERIAL_DELAY*5 && serial_read_pin(); i++ ) {
+ }
+ // This shouldn't hang if the target disconnects because the
+ // serial line will float to high if the target does disconnect.
+ while (!serial_read_pin());
+}
+
+// Used by the reciver to send a synchronization signal to the sender.
+static void sync_send(void) NO_INLINE;
+static
+void sync_send(void) {
+ serial_low();
+ serial_delay();
+ serial_high();
+}
+
+// Reads a byte from the serial line
+static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
+static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
+ uint8_t byte, i, p, pb;
+
+ _delay_sub_us(READ_WRITE_START_ADJUST);
+ for( i = 0, byte = 0, p = PARITY; i < bit; i++ ) {
+ serial_delay_half1(); // read the middle of pulses
+ if( serial_read_pin() ) {
+ byte = (byte << 1) | 1; p ^= 1;
+ } else {
+ byte = (byte << 1) | 0; p ^= 0;
+ }
+ _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
+ serial_delay_half2();
+ }
+ /* recive parity bit */
+ serial_delay_half1(); // read the middle of pulses
+ pb = serial_read_pin();
+ _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
+ serial_delay_half2();
+
+ *pterrcount += (p != pb)? 1 : 0;
+
+ return byte;
+}
+
+// Sends a byte with MSB ordering
+void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
+void serial_write_chunk(uint8_t data, uint8_t bit) {
+ uint8_t b, p;
+ for( p = PARITY, b = 1<<(bit-1); b ; b >>= 1) {
+ if(data & b) {
+ serial_high(); p ^= 1;
+ } else {
+ serial_low(); p ^= 0;
+ }
+ serial_delay();
+ }
+ /* send parity bit */
+ if(p & 1) { serial_high(); }
+ else { serial_low(); }
+ serial_delay();
+
+ serial_low(); // sync_send() / senc_recv() need raise edge
+}
+
+static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
+static
+void serial_send_packet(uint8_t *buffer, uint8_t size) {
+ for (uint8_t i = 0; i < size; ++i) {
+ uint8_t data;
+ data = buffer[i];
+ sync_send();
+ serial_write_chunk(data,8);
+ }
+}
+
+static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
+static
+uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
+ uint8_t pecount = 0;
+ for (uint8_t i = 0; i < size; ++i) {
+ uint8_t data;
+ sync_recv();
+ data = serial_read_chunk(&pecount, 8);
+ buffer[i] = data;
+ }
+ return pecount == 0;
+}
+
+inline static
+void change_sender2reciver(void) {
+ sync_send(); //0
+ serial_delay_half1(); //1
+ serial_low(); //2
+ serial_input_with_pullup(); //2
+ serial_delay_half1(); //3
+}
+
+inline static
+void change_reciver2sender(void) {
+ sync_recv(); //0
+ serial_delay(); //1
+ serial_low(); //3
+ serial_output(); //3
+ serial_delay_half1(); //4
+}
+
+static inline uint8_t nibble_bits_count(uint8_t bits)
+{
+ bits = (bits & 0x5) + (bits >> 1 & 0x5);
+ bits = (bits & 0x3) + (bits >> 2 & 0x3);
+ return bits;
+}
+
+// interrupt handle to be used by the target device
+ISR(SERIAL_PIN_INTERRUPT) {
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+ serial_low();
+ serial_output();
+ SSTD_t *trans = Transaction_table;
+#else
+ // recive transaction table index
+ uint8_t tid, bits;
+ uint8_t pecount = 0;
+ sync_recv();
+ bits = serial_read_chunk(&pecount,7);
+ tid = bits>>3;
+ bits = (bits&7) != nibble_bits_count(tid);
+ if( bits || pecount> 0 || tid > Transaction_table_size ) {
+ return;
+ }
+ serial_delay_half1();
+
+ serial_high(); // response step1 low->high
+ serial_output();
+ _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT*SLAVE_INT_ACK_WIDTH);
+ SSTD_t *trans = &Transaction_table[tid];
+ serial_low(); // response step2 ack high->low
+#endif
+
+ // target send phase
+ if( trans->target2initiator_buffer_size > 0 )
+ serial_send_packet((uint8_t *)trans->target2initiator_buffer,
+ trans->target2initiator_buffer_size);
+ // target switch to input
+ change_sender2reciver();
+
+ // target recive phase
+ if( trans->initiator2target_buffer_size > 0 ) {
+ if (serial_recive_packet((uint8_t *)trans->initiator2target_buffer,
+ trans->initiator2target_buffer_size) ) {
+ *trans->status = TRANSACTION_ACCEPTED;
+ } else {
+ *trans->status = TRANSACTION_DATA_ERROR;
+ }
+ } else {
+ *trans->status = TRANSACTION_ACCEPTED;
+ }
+
+ sync_recv(); //weit initiator output to high
+}
+
+/////////
+// start transaction by initiator
+//
+// int soft_serial_transaction(int sstd_index)
+//
+// Returns:
+// TRANSACTION_END
+// TRANSACTION_NO_RESPONSE
+// TRANSACTION_DATA_ERROR
+// this code is very time dependent, so we need to disable interrupts
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+int soft_serial_transaction(void) {
+ SSTD_t *trans = Transaction_table;
+#else
+int soft_serial_transaction(int sstd_index) {
+ if( sstd_index > Transaction_table_size )
+ return TRANSACTION_TYPE_ERROR;
+ SSTD_t *trans = &Transaction_table[sstd_index];
+#endif
+ cli();
+
+ // signal to the target that we want to start a transaction
+ serial_output();
+ serial_low();
+ _delay_us(SLAVE_INT_WIDTH_US);
+
+#ifndef SERIAL_USE_MULTI_TRANSACTION
+ // wait for the target response
+ serial_input_with_pullup();
+ _delay_us(SLAVE_INT_RESPONSE_TIME);
+
+ // check if the target is present
+ if (serial_read_pin()) {
+ // target failed to pull the line low, assume not present
+ serial_output();
+ serial_high();
+ *trans->status = TRANSACTION_NO_RESPONSE;
+ sei();
+ return TRANSACTION_NO_RESPONSE;
+ }
+
+#else
+ // send transaction table index
+ int tid = (sstd_index<<3) | (7 & nibble_bits_count(sstd_index));
+ sync_send();
+ _delay_sub_us(TID_SEND_ADJUST);
+ serial_write_chunk(tid, 7);
+ serial_delay_half1();
+
+ // wait for the target response (step1 low->high)
+ serial_input_with_pullup();
+ while( !serial_read_pin() ) {
+ _delay_sub_us(2);
+ }
+
+ // check if the target is present (step2 high->low)
+ for( int i = 0; serial_read_pin(); i++ ) {
+ if (i > SLAVE_INT_ACK_WIDTH + 1) {
+ // slave failed to pull the line low, assume not present
+ serial_output();
+ serial_high();
+ *trans->status = TRANSACTION_NO_RESPONSE;
+ sei();
+ return TRANSACTION_NO_RESPONSE;
+ }
+ _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
+ }
+#endif
+
+ // initiator recive phase
+ // if the target is present syncronize with it
+ if( trans->target2initiator_buffer_size > 0 ) {
+ if (!serial_recive_packet((uint8_t *)trans->target2initiator_buffer,
+ trans->target2initiator_buffer_size) ) {
+ serial_output();
+ serial_high();
+ *trans->status = TRANSACTION_DATA_ERROR;
+ sei();
+ return TRANSACTION_DATA_ERROR;
+ }
+ }
+
+ // initiator switch to output
+ change_reciver2sender();
+
+ // initiator send phase
+ if( trans->initiator2target_buffer_size > 0 ) {
+ serial_send_packet((uint8_t *)trans->initiator2target_buffer,
+ trans->initiator2target_buffer_size);
+ }
+
+ // always, release the line when not in use
+ sync_send();
+
+ *trans->status = TRANSACTION_END;
+ sei();
+ return TRANSACTION_END;
+}
+
+#ifdef SERIAL_USE_MULTI_TRANSACTION
+int soft_serial_get_and_clean_status(int sstd_index) {
+ SSTD_t *trans = &Transaction_table[sstd_index];
+ cli();
+ int retval = *trans->status;
+ *trans->status = 0;;
+ sei();
+ return retval;
+}
+#endif
+
+#endif
+
+// Helix serial.c history
+// 2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
+// 2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
+// (adjusted with avr-gcc 4.9.2)
+// 2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
+// (adjusted with avr-gcc 4.9.2)
+// 2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
+// (adjusted with avr-gcc 4.9.2)
+// 2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
+// (adjusted with avr-gcc 7.3.0)
+// 2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
+// (adjusted with avr-gcc 5.4.0, 7.3.0)
generated by cgit v1.2.3-24-g4f1b (git 2.32.0) at 2024-11-21 20:59:30 +0100