diff options
Diffstat (limited to 'keyboards/zen/rules.mk')
| -rw-r--r-- | keyboards/zen/rules.mk | 69 |
1 files changed, 19 insertions, 50 deletions
diff --git a/keyboards/zen/rules.mk b/keyboards/zen/rules.mk index 4e8268911..f5d64a7f0 100644 --- a/keyboards/zen/rules.mk +++ b/keyboards/zen/rules.mk @@ -1,51 +1,26 @@ -SRC += matrix.c \ - split_util.c \ - serial.c - -# MCU name -#MCU = at90usb1287 +# Pro Micro or Elite-C +# Automagically converted to Proton-C MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) +BOOTLOADER = dfu +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. -BOOTLOADER = caterina +ifeq ($(strip $(CTPC)), yes) + CONVERT_TO_PROTON_C=yes +endif -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +ifeq ($(strip $(CONVERT_TO_PROTON_C)), yes) + SPLIT_KEYBOARD = no # currently unsupported on ARM + RGBLIGHT_ENABLE = no # currently unsupported on ARM + + EXTRAFLAGS += -DUSE_PROTON_C +else + # Currently moved to Pro Micro only section because of lack of Proton-C support + SPLIT_KEYBOARD = yes + RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. +endif # Build Options # change to "no" to disable the options, or define them in the Makefile in @@ -57,17 +32,11 @@ EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality MIDI_ENABLE = no # MIDI controls AUDIO_ENABLE = no # Audio output on port C6 UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. -SUBPROJECT_rev1 = yes -USE_I2C = no -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -CUSTOM_MATRIX = yes +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -DEFAULT_FOLDER = zen/rev1 +DEFAULT_FOLDER = zen/rev2 |