diff options
Diffstat (limited to 'keyboards')
| -rw-r--r-- | keyboards/minivan44/Makefile | 75 | ||||
| -rw-r--r-- | keyboards/minivan44/config.h | 162 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/default/Makefile | 21 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/default/config.h | 8 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/default/keymap.c | 97 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/default/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/xyverz/Makefile | 21 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/xyverz/config.h | 8 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/xyverz/keymap.c | 92 | ||||
| -rw-r--r-- | keyboards/minivan44/keymaps/xyverz/readme.md | 1 | ||||
| -rw-r--r-- | keyboards/minivan44/minivan44.c | 28 | ||||
| -rw-r--r-- | keyboards/minivan44/minivan44.h | 22 | ||||
| -rw-r--r-- | keyboards/minivan44/readme.md | 28 |
13 files changed, 0 insertions, 564 deletions
diff --git a/keyboards/minivan44/Makefile b/keyboards/minivan44/Makefile deleted file mode 100644 index 45ca12780..000000000 --- a/keyboards/minivan44/Makefile +++ /dev/null @@ -1,75 +0,0 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= yes # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR - include ../../Makefile -endif - - diff --git a/keyboards/minivan44/config.h b/keyboards/minivan44/config.h deleted file mode 100644 index 0ae93c095..000000000 --- a/keyboards/minivan44/config.h +++ /dev/null @@ -1,162 +0,0 @@ -/* -Copyright 2012 Jun Wako <wakojun@gmail.com> - -This program is free software: you can redistribute it and/or modify -it under the terms of the GNU General Public License as published by -the Free Software Foundation, either version 2 of the License, or -(at your option) any later version. - -This program is distributed in the hope that it will be useful, -but WITHOUT ANY WARRANTY; without even the implied warranty of -MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -GNU General Public License for more details. - -You should have received a copy of the GNU General Public License -along with this program. If not, see <http://www.gnu.org/licenses/>. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEAE -#define PRODUCT_ID 0x8844 -#define DEVICE_VER 0x0002 -#define MANUFACTURER Evan Sailer -#define PRODUCT TheVan 44 -#define DESCRIPTION keyboard firmware for TV44 - -/* key matrix size */ -#define MATRIX_ROWS 4 -#define MATRIX_COLS 12 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ -#define MATRIX_ROW_PINS { D7, B5, F7, D4 } -#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -// #define BACKLIGHT_PIN B7 -// #define BACKLIGHT_BREATHING -// #define BACKLIGHT_LEVELS 3 - - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCING_DELAY 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - -/* - * Magic Key Options - * - * Magic keys are hotkey commands that allow control over firmware functions of - * the keyboard. They are best used in combination with the HID Listen program, - * found here: https://www.pjrc.com/teensy/hid_listen.html - * - * The options below allow the magic key functionality to be changed. This is - * useful if your keyboard/keypad is missing keys and you want magic key support. - * - */ - -/* key combination for magic key command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* override magic key keymap */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -//#define MAGIC_KEY_LOCK CAPS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -#endif diff --git a/keyboards/minivan44/keymaps/default/Makefile b/keyboards/minivan44/keymaps/default/Makefile deleted file mode 100644 index f4671a9d1..000000000 --- a/keyboards/minivan44/keymaps/default/Makefile +++ /dev/null @@ -1,21 +0,0 @@ -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR - include ../../../../Makefile -endif
\ No newline at end of file diff --git a/keyboards/minivan44/keymaps/default/config.h b/keyboards/minivan44/keymaps/default/config.h deleted file mode 100644 index df06a2620..000000000 --- a/keyboards/minivan44/keymaps/default/config.h +++ /dev/null @@ -1,8 +0,0 @@ -#ifndef CONFIG_USER_H -#define CONFIG_USER_H - -#include "../../config.h" - -// place overrides here - -#endif
\ No newline at end of file diff --git a/keyboards/minivan44/keymaps/default/keymap.c b/keyboards/minivan44/keymaps/default/keymap.c deleted file mode 100644 index d559a4b1c..000000000 --- a/keyboards/minivan44/keymaps/default/keymap.c +++ /dev/null @@ -1,97 +0,0 @@ -#include "minivan44.h" -#include "action_layer.h" -#include "eeconfig.h" - -extern keymap_config_t keymap_config; - -// Each layer gets a name for readability, which is then used in the keymap matrix below. -// The underscores don't mean anything - you can have a layer called STUFF or any other name. -// Layer names don't all need to be of the same length, obviously, and you can also skip them -// entirely and just use numbers. - -#define _QW 0 -#define _DV 1 -#define _CM 2 -#define _L1 3 -#define _L2 4 -#define _L3 5 - -// Macro name shortcuts -#define QWERTY M(_QW) -#define DVORAK M(_DV) -#define COLEMAK M(_CM) - -// Fillers to make layering more clear -#define _______ KC_TRNS -#define XXXXXXX KC_NO - - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { - [_QW] = { /* Qwerty */ - {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, - {MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, MO(_L1) }, - {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_F, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) }, - {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } - }, - [_DV] = { /* Dvorak */ - {KC_TAB, KC_COMM, KC_DOT, KC_SLSH, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_Q, KC_BSPC }, - {MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, MO(_L1) }, - {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, MO(_L2) }, - {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } - }, - [_CM] = { /* Colemak */ - {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC }, - {MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, MO(_L1) }, - {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, MO(_L2) }, - {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_RALT, KC_ESC, XXXXXXX, TG(_L3) } - }, - [_L1] = { /* LAYER 1 */ - {KC_GRV, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL }, - {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ }, - {_______, KC_ESC, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, - {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } - }, - [_L2] = { /* LAYER 2 */ - {_______, QWERTY, DVORAK, COLEMAK, _______, _______, _______, KC_7, KC_8, KC_9, KC_0, _______ }, - {KC_ESC, KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4, KC_5, KC_6, KC_VOLU, KC_ENT }, - {_______, _______, _______, _______, _______, _______, KC_0, KC_1, KC_2, KC_3, KC_VOLD, _______ }, - {_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ } - }, - [_L3] = { /* LAYER 3 */ - {_______, _______, _______, _______, _______, _______, _______, KC_F1, KC_F2, KC_F3, KC_F4, _______ }, - {KC_ESC, _______, _______, _______, _______, _______, _______, KC_F5, KC_F6, KC_F7, KC_F8, _______ }, - {KC_LSFT, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_F9, KC_F10, KC_F11, KC_F12, _______ }, - {_______, KC_LSFT, KC_B, KC_SPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_C, _______, _______, XXXXXXX, _______ } - } -}; - -const uint16_t PROGMEM fn_actions[] = { - -}; - -void persistant_default_layer_set(uint16_t default_layer) { - eeconfig_update_default_layer(default_layer); - default_layer_set(default_layer); -} - -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - switch(id) { - case _DV: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_DV); - } - break; - case _QW: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_QW); - } - break; - case _CM: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_CM); - } - break; - } - return MACRO_NONE; -}; diff --git a/keyboards/minivan44/keymaps/default/readme.md b/keyboards/minivan44/keymaps/default/readme.md deleted file mode 100644 index 189a9c0ff..000000000 --- a/keyboards/minivan44/keymaps/default/readme.md +++ /dev/null @@ -1 +0,0 @@ -# The default keymap for minivan44
\ No newline at end of file diff --git a/keyboards/minivan44/keymaps/xyverz/Makefile b/keyboards/minivan44/keymaps/xyverz/Makefile deleted file mode 100644 index f4671a9d1..000000000 --- a/keyboards/minivan44/keymaps/xyverz/Makefile +++ /dev/null @@ -1,21 +0,0 @@ -# Build Options -# change to "no" to disable the options, or define them in the Makefile in -# the appropriate keymap folder that will get included automatically -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no # Audio output on port C6 -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend - -ifndef QUANTUM_DIR - include ../../../../Makefile -endif
\ No newline at end of file diff --git a/keyboards/minivan44/keymaps/xyverz/config.h b/keyboards/minivan44/keymaps/xyverz/config.h deleted file mode 100644 index df06a2620..000000000 --- a/keyboards/minivan44/keymaps/xyverz/config.h +++ /dev/null @@ -1,8 +0,0 @@ -#ifndef CONFIG_USER_H -#define CONFIG_USER_H - -#include "../../config.h" - -// place overrides here - -#endif
\ No newline at end of file diff --git a/keyboards/minivan44/keymaps/xyverz/keymap.c b/keyboards/minivan44/keymaps/xyverz/keymap.c deleted file mode 100644 index f995da0e7..000000000 --- a/keyboards/minivan44/keymaps/xyverz/keymap.c +++ /dev/null @@ -1,92 +0,0 @@ -#include "minivan44.h" -#include "action_layer.h" -#include "eeconfig.h" - -extern keymap_config_t keymap_config; - -#define _DV 0 -#define _QW 1 -#define _CM 2 -#define _L1 3 -#define _L2 4 - -// Macro name shortcuts -#define DVORAK M(_DV) -#define QWERTY M(_QW) -#define COLEMAK M(_CM) - -// Fillers to make layering more clear -#define _______ KC_TRNS -#define XXXXXXX KC_NO - - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { - [_DV] = { /* 0: Dvorak */ - {KC_TAB, KC_QUOT, KC_COMM, KC_DOT, KC_P, KC_Y, KC_F, KC_G, KC_C, KC_R, KC_L, KC_BSPC }, - {MO(_L1), KC_A, KC_O, KC_E, KC_U, KC_I, KC_D, KC_H, KC_T, KC_N, KC_S, KC_ENT }, - {KC_LSFT, KC_SCLN, KC_Q, KC_J, KC_K, KC_X, KC_B, KC_M, KC_W, KC_V, KC_Z, KC_RSFT }, - {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } - }, - - [_QW] = { /* 1: Qwerty */ - {KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, - {MO(_L1), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT }, - {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, - {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } - }, - - [_CM] = { /* 2: Colemak */ - {KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_BSPC }, - {MO(_L1), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_ENT }, - {KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT }, - {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC, KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) } - }, - - [_L1] = {/* 1: FN 1 */ - {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL }, - {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_DOWN, KC_UP, KC_LEFT, KC_RGHT, _______ }, - {_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT }, - {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ } - }, - - [_L2] = { /* 2: FN 2 */ - {KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_ESC }, - {_______, KC_F11, KC_F12, _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT }, - {_______, _______, _______, _______, _______, _______, _______, _______, KC_END, KC_PGDN, KC_VOLD, _______ }, - {QWERTY, DVORAK, COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ } - } - -}; - -const uint16_t PROGMEM fn_actions[] = { - -}; - -void persistant_default_layer_set(uint16_t default_layer) { - eeconfig_update_default_layer(default_layer); - default_layer_set(default_layer); -} - -const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) -{ - switch(id) { - case _DV: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_DV); - } - break; - case _QW: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_QW); - } - break; - case _CM: - if (record->event.pressed) { - persistant_default_layer_set(1UL<<_CM); - } - break; - } - return MACRO_NONE; -}; - - diff --git a/keyboards/minivan44/keymaps/xyverz/readme.md b/keyboards/minivan44/keymaps/xyverz/readme.md deleted file mode 100644 index 189a9c0ff..000000000 --- a/keyboards/minivan44/keymaps/xyverz/readme.md +++ /dev/null @@ -1 +0,0 @@ -# The default keymap for minivan44
\ No newline at end of file diff --git a/keyboards/minivan44/minivan44.c b/keyboards/minivan44/minivan44.c deleted file mode 100644 index be8214fd5..000000000 --- a/keyboards/minivan44/minivan44.c +++ /dev/null @@ -1,28 +0,0 @@ -#include "minivan44.h" - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - - matrix_init_user(); -} - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - - matrix_scan_user(); -} - -bool process_record_kb(uint16_t keycode, keyrecord_t *record) { - // put your per-action keyboard code here - // runs for every action, just before processing by the firmware - - return process_record_user(keycode, record); -} - -void led_set_kb(uint8_t usb_led) { - // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here - - led_set_user(usb_led); -} diff --git a/keyboards/minivan44/minivan44.h b/keyboards/minivan44/minivan44.h deleted file mode 100644 index c6119c2e1..000000000 --- a/keyboards/minivan44/minivan44.h +++ /dev/null @@ -1,22 +0,0 @@ -#ifndef MINIVAN44_H -#define MINIVAN44_H - -#include "quantum.h" - -// This a shortcut to help you visually see your layout. -// The following is an example using the Planck MIT layout -// The first section contains all of the arguements -// The second converts the arguments into a two-dimensional array -#define KEYMAP( \ - K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \ - K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \ - K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \ - K30, K31, K32, K33, K37, K38, K39, K3B \ -) \ -{ \ - { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B }, \ - { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B }, \ - { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B }, \ - { K30, K31, K32, K33, KC_NO, KC_NO, KC_NO, K37, K38, K39, K3A, K3B } \ - -#endif diff --git a/keyboards/minivan44/readme.md b/keyboards/minivan44/readme.md deleted file mode 100644 index 59b62b0e6..000000000 --- a/keyboards/minivan44/readme.md +++ /dev/null @@ -1,28 +0,0 @@ -minivan44 keyboard firmware -====================== - -## Quantum MK Firmware - -For the full Quantum feature list, see [the parent readme.md](/doc/readme.md). - -## Building - -Download or clone the whole firmware and navigate to the keyboards/minivan44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. - -Depending on which keymap you would like to use, you will have to compile slightly differently. - -### Default - -To build with the default keymap, simply run `make`. - -### Other Keymaps - -Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files. - -To build the firmware binary hex file with a keymap just do `make` with `keymap` option like: - -``` -$ make keymap=[default|jack|<name>] -``` - -Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
\ No newline at end of file |