1 files changed, 75 insertions, 75 deletions
diff --git a/lib/lufa/Bootloaders/MassStorage/makefile b/lib/lufa/Bootloaders/MassStorage/makefile
index 7f0ec82a7..f3948e754 100644
--- a/lib/lufa/Bootloaders/MassStorage/makefile
+++ b/lib/lufa/Bootloaders/MassStorage/makefile
@@ -1,75 +1,75 @@
-#
-#             LUFA Library
-#     Copyright (C) Dean Camera, 2017.
-#
-#  dean [at] fourwalledcubicle [dot] com
-#           www.lufa-lib.org
-#
-# --------------------------------------
-#         LUFA Project Makefile.
-# --------------------------------------
-
-# Run "make help" for target help.
-
-MCU          = at90usb1287
-ARCH         = AVR8
-BOARD        = USBKEY
-F_CPU        = 8000000
-F_USB        = $(F_CPU)
-OPTIMIZATION = s
-TARGET       = BootloaderMassStorage
-SRC          = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S Lib/SCSI.c Lib/VirtualFAT.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS)
-LUFA_PATH    = ../../LUFA
-CC_FLAGS     = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET)
-LD_FLAGS     = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS)
-
-# Flash size and bootloader section sizes of the target, in KB. These must
-# match the target's total FLASH size and the bootloader size set in the
-# device's fuses.
-FLASH_SIZE_KB         = 128
-BOOT_SECTION_SIZE_KB  = 8
-
-# Bootloader address calculation formulas
-# Do not modify these macros, but rather modify the dependent values above.
-CALC_ADDRESS_IN_HEX   = $(shell printf "0x%X" $$(( $(1) )) )
-BOOT_START_OFFSET     = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 )
-BOOT_SEC_OFFSET       = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) )
-
-# Bootloader linker section flags for relocating the API table sections to
-# known FLASH addresses - these should not normally be user-edited.
-BOOT_SECTION_LD_FLAG  = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2))
-BOOT_API_LD_FLAGS     = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96)
-BOOT_API_LD_FLAGS    += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable,   BootloaderAPI_JumpTable,   32)
-BOOT_API_LD_FLAGS    += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures,  BootloaderAPI_Signatures,  8)
-
-# Check if the bootloader needs an AUX section, located before the real bootloader section to store some of the
-# bootloader code. This is required for 32KB and smaller devices, where the actual bootloader is 6KB but the maximum
-# bootloader section size is 4KB. The actual usable application space will be reduced by 6KB for these devices.
-ifeq ($(BOOT_SECTION_SIZE_KB),8)
-  CC_FLAGS           += -DAUX_BOOT_SECTION_SIZE=0
-else
-  AUX_BOOT_SECTION_SIZE_KB = (6 - $(BOOT_SECTION_SIZE_KB))
-
-  CC_FLAGS           += -DAUX_BOOT_SECTION_SIZE='($(AUX_BOOT_SECTION_SIZE_KB) * 1024)'
-  LD_FLAGS           += -Wl,--section-start=.boot_aux=$(call BOOT_SEC_OFFSET, (($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024 - 16))
-  LD_FLAGS           += $(call BOOT_SECTION_LD_FLAG, .boot_aux_trampoline, Boot_AUX_Trampoline, ($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024)
-endif
-
-# Default target
-all:
-
-# Include LUFA-specific DMBS extension modules
-DMBS_LUFA_PATH ?= $(LUFA_PATH)/Build/LUFA
-include $(DMBS_LUFA_PATH)/lufa-sources.mk
-include $(DMBS_LUFA_PATH)/lufa-gcc.mk
-
-# Include common DMBS build system modules
-DMBS_PATH      ?= $(LUFA_PATH)/Build/DMBS/DMBS
-include $(DMBS_PATH)/core.mk
-include $(DMBS_PATH)/cppcheck.mk
-include $(DMBS_PATH)/doxygen.mk
-include $(DMBS_PATH)/dfu.mk
-include $(DMBS_PATH)/gcc.mk
-include $(DMBS_PATH)/hid.mk
-include $(DMBS_PATH)/avrdude.mk
-include $(DMBS_PATH)/atprogram.mk
+#
+#             LUFA Library
+#     Copyright (C) Dean Camera, 2017.
+#
+#  dean [at] fourwalledcubicle [dot] com
+#           www.lufa-lib.org
+#
+# --------------------------------------
+#         LUFA Project Makefile.
+# --------------------------------------
+
+# Run "make help" for target help.
+
+MCU          = at90usb1287
+ARCH         = AVR8
+BOARD        = USBKEY
+F_CPU        = 8000000
+F_USB        = $(F_CPU)
+OPTIMIZATION = s
+TARGET       = BootloaderMassStorage
+SRC          = $(TARGET).c Descriptors.c BootloaderAPI.c BootloaderAPITable.S Lib/SCSI.c Lib/VirtualFAT.c $(LUFA_SRC_USB) $(LUFA_SRC_USBCLASS)
+LUFA_PATH    = ../../LUFA
+CC_FLAGS     = -DUSE_LUFA_CONFIG_HEADER -IConfig/ -DBOOT_START_ADDR=$(BOOT_START_OFFSET)
+LD_FLAGS     = -Wl,--section-start=.text=$(BOOT_START_OFFSET) $(BOOT_API_LD_FLAGS)
+
+# Flash size and bootloader section sizes of the target, in KB. These must
+# match the target's total FLASH size and the bootloader size set in the
+# device's fuses.
+FLASH_SIZE_KB         = 128
+BOOT_SECTION_SIZE_KB  = 8
+
+# Bootloader address calculation formulas
+# Do not modify these macros, but rather modify the dependent values above.
+CALC_ADDRESS_IN_HEX   = $(shell printf "0x%X" $$(( $(1) )) )
+BOOT_START_OFFSET     = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) - $(BOOT_SECTION_SIZE_KB)) * 1024 )
+BOOT_SEC_OFFSET       = $(call CALC_ADDRESS_IN_HEX, ($(FLASH_SIZE_KB) * 1024) - ($(strip $(1))) )
+
+# Bootloader linker section flags for relocating the API table sections to
+# known FLASH addresses - these should not normally be user-edited.
+BOOT_SECTION_LD_FLAG  = -Wl,--section-start=$(strip $(1))=$(call BOOT_SEC_OFFSET, $(3)) -Wl,--undefined=$(strip $(2))
+BOOT_API_LD_FLAGS     = $(call BOOT_SECTION_LD_FLAG, .apitable_trampolines, BootloaderAPI_Trampolines, 96)
+BOOT_API_LD_FLAGS    += $(call BOOT_SECTION_LD_FLAG, .apitable_jumptable,   BootloaderAPI_JumpTable,   32)
+BOOT_API_LD_FLAGS    += $(call BOOT_SECTION_LD_FLAG, .apitable_signatures,  BootloaderAPI_Signatures,  8)
+
+# Check if the bootloader needs an AUX section, located before the real bootloader section to store some of the
+# bootloader code. This is required for 32KB and smaller devices, where the actual bootloader is 6KB but the maximum
+# bootloader section size is 4KB. The actual usable application space will be reduced by 6KB for these devices.
+ifeq ($(BOOT_SECTION_SIZE_KB),8)
+  CC_FLAGS           += -DAUX_BOOT_SECTION_SIZE=0
+else
+  AUX_BOOT_SECTION_SIZE_KB = (6 - $(BOOT_SECTION_SIZE_KB))
+
+  CC_FLAGS           += -DAUX_BOOT_SECTION_SIZE='($(AUX_BOOT_SECTION_SIZE_KB) * 1024)'
+  LD_FLAGS           += -Wl,--section-start=.boot_aux=$(call BOOT_SEC_OFFSET, (($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024 - 16))
+  LD_FLAGS           += $(call BOOT_SECTION_LD_FLAG, .boot_aux_trampoline, Boot_AUX_Trampoline, ($(BOOT_SECTION_SIZE_KB) + $(AUX_BOOT_SECTION_SIZE_KB)) * 1024)
+endif
+
+# Default target
+all:
+
+# Include LUFA-specific DMBS extension modules
+DMBS_LUFA_PATH ?= $(LUFA_PATH)/Build/LUFA
+include $(DMBS_LUFA_PATH)/lufa-sources.mk
+include $(DMBS_LUFA_PATH)/lufa-gcc.mk
+
+# Include common DMBS build system modules
+DMBS_PATH      ?= $(LUFA_PATH)/Build/DMBS/DMBS
+include $(DMBS_PATH)/core.mk
+include $(DMBS_PATH)/cppcheck.mk
+include $(DMBS_PATH)/doxygen.mk
+include $(DMBS_PATH)/dfu.mk
+include $(DMBS_PATH)/gcc.mk
+include $(DMBS_PATH)/hid.mk
+include $(DMBS_PATH)/avrdude.mk
+include $(DMBS_PATH)/atprogram.mk