diff options
Diffstat (limited to 'tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/BootloaderDFU.c')
| -rw-r--r-- | tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/BootloaderDFU.c | 804 |
1 files changed, 0 insertions, 804 deletions
diff --git a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/BootloaderDFU.c b/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/BootloaderDFU.c deleted file mode 100644 index 00e673268..000000000 --- a/tmk_core/protocol/lufa/LUFA-git/Bootloaders/DFU/BootloaderDFU.c +++ /dev/null @@ -1,804 +0,0 @@ -/* - LUFA Library - Copyright (C) Dean Camera, 2014. - - dean [at] fourwalledcubicle [dot] com - www.lufa-lib.org -*/ - -/* - Copyright 2014 Dean Camera (dean [at] fourwalledcubicle [dot] com) - - Permission to use, copy, modify, distribute, and sell this - software and its documentation for any purpose is hereby granted - without fee, provided that the above copyright notice appear in - all copies and that both that the copyright notice and this - permission notice and warranty disclaimer appear in supporting - documentation, and that the name of the author not be used in - advertising or publicity pertaining to distribution of the - software without specific, written prior permission. - - The author disclaims all warranties with regard to this - software, including all implied warranties of merchantability - and fitness. In no event shall the author be liable for any - special, indirect or consequential damages or any damages - whatsoever resulting from loss of use, data or profits, whether - in an action of contract, negligence or other tortious action, - arising out of or in connection with the use or performance of - this software. -*/ - -/** \file - * - * Main source file for the DFU class bootloader. This file contains the complete bootloader logic. - */ - -#define INCLUDE_FROM_BOOTLOADER_C -#include "BootloaderDFU.h" - -/** Flag to indicate if the bootloader is currently running in secure mode, disallowing memory operations - * other than erase. This is initially set to the value set by SECURE_MODE, and cleared by the bootloader - * once a memory erase has completed in a bootloader session. - */ -static bool IsSecure = SECURE_MODE; - -/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run - * via a soft reset. When cleared, the bootloader will abort, the USB interface will shut down and the application - * jumped to via an indirect jump to location 0x0000 (or other location specified by the host). - */ -static bool RunBootloader = true; - -/** Flag to indicate if the bootloader is waiting to exit. When the host requests the bootloader to exit and - * jump to the application address it specifies, it sends two sequential commands which must be properly - * acknowledged. Upon reception of the first the RunBootloader flag is cleared and the WaitForExit flag is set, - * causing the bootloader to wait for the final exit command before shutting down. - */ -static bool WaitForExit = false; - -/** Current DFU state machine state, one of the values in the DFU_State_t enum. */ -static uint8_t DFU_State = dfuIDLE; - -/** Status code of the last executed DFU command. This is set to one of the values in the DFU_Status_t enum after - * each operation, and returned to the host when a Get Status DFU request is issued. - */ -static uint8_t DFU_Status = OK; - -/** Data containing the DFU command sent from the host. */ -static DFU_Command_t SentCommand; - -/** Response to the last issued Read Data DFU command. Unlike other DFU commands, the read command - * requires a single byte response from the bootloader containing the read data when the next DFU_UPLOAD command - * is issued by the host. - */ -static uint8_t ResponseByte; - -/** Pointer to the start of the user application. By default this is 0x0000 (the reset vector), however the host - * may specify an alternate address when issuing the application soft-start command. - */ -static AppPtr_t AppStartPtr = (AppPtr_t)0x0000; - -/** 64-bit flash page number. This is concatenated with the current 16-bit address on USB AVRs containing more than - * 64KB of flash memory. - */ -static uint8_t Flash64KBPage = 0; - -/** Memory start address, indicating the current address in the memory being addressed (either FLASH or EEPROM - * depending on the issued command from the host). - */ -static uint16_t StartAddr = 0x0000; - -/** Memory end address, indicating the end address to read from/write to in the memory being addressed (either FLASH - * of EEPROM depending on the issued command from the host). - */ -static uint16_t EndAddr = 0x0000; - -/** Magic lock for forced application start. If the HWBE fuse is programmed and BOOTRST is unprogrammed, the bootloader - * will start if the /HWB line of the AVR is held low and the system is reset. However, if the /HWB line is still held - * low when the application attempts to start via a watchdog reset, the bootloader will re-start. If set to the value - * \ref MAGIC_BOOT_KEY the special init function \ref Application_Jump_Check() will force the application to start. - */ -uint16_t MagicBootKey ATTR_NO_INIT; - - -/** Special startup routine to check if the bootloader was started via a watchdog reset, and if the magic application - * start key has been loaded into \ref MagicBootKey. If the bootloader started via the watchdog and the key is valid, - * this will force the user application to start via a software jump. - */ -void Application_Jump_Check(void) -{ - bool JumpToApplication = false; - - #if ((BOARD == BOARD_XPLAIN) || (BOARD == BOARD_XPLAIN_REV1)) - /* Disable JTAG debugging */ - JTAG_DISABLE(); - - /* Enable pull-up on the JTAG TCK pin so we can use it to select the mode */ - PORTF |= (1 << 4); - Delay_MS(10); - - /* If the TCK pin is not jumpered to ground, start the user application instead */ - JumpToApplication |= ((PINF & (1 << 4)) != 0); - - /* Re-enable JTAG debugging */ - JTAG_ENABLE(); - #endif - - /* If the reset source was the bootloader and the key is correct, clear it and jump to the application */ - if ((MCUSR & (1 << WDRF)) && (MagicBootKey == MAGIC_BOOT_KEY)) - JumpToApplication |= true; - - /* If a request has been made to jump to the user application, honor it */ - if (JumpToApplication) - { - /* Turn off the watchdog */ - MCUSR &= ~(1<<WDRF); - wdt_disable(); - - /* Clear the boot key and jump to the user application */ - MagicBootKey = 0; - - // cppcheck-suppress constStatement - ((void (*)(void))0x0000)(); - } -} - -/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously - * runs the bootloader processing routine until instructed to soft-exit, or hard-reset via the watchdog to start - * the loaded application code. - */ -int main(void) -{ - /* Configure hardware required by the bootloader */ - SetupHardware(); - - /* Turn on first LED on the board to indicate that the bootloader has started */ - LEDs_SetAllLEDs(LEDS_LED1); - - /* Enable global interrupts so that the USB stack can function */ - GlobalInterruptEnable(); - - /* Run the USB management task while the bootloader is supposed to be running */ - while (RunBootloader || WaitForExit) - USB_USBTask(); - - /* Reset configured hardware back to their original states for the user application */ - ResetHardware(); - - /* Start the user application */ - AppStartPtr(); -} - -/** Configures all hardware required for the bootloader. */ -static void SetupHardware(void) -{ - /* Disable watchdog if enabled by bootloader/fuses */ - MCUSR &= ~(1 << WDRF); - wdt_disable(); - - /* Disable clock division */ - clock_prescale_set(clock_div_1); - - /* Relocate the interrupt vector table to the bootloader section */ - MCUCR = (1 << IVCE); - MCUCR = (1 << IVSEL); - - /* Initialize the USB and other board hardware drivers */ - USB_Init(); - LEDs_Init(); - - /* Bootloader active LED toggle timer initialization */ - TIMSK1 = (1 << TOIE1); - TCCR1B = ((1 << CS11) | (1 << CS10)); -} - -/** Resets all configured hardware required for the bootloader back to their original states. */ -static void ResetHardware(void) -{ - /* Shut down the USB and other board hardware drivers */ - USB_Disable(); - LEDs_Disable(); - - /* Disable Bootloader active LED toggle timer */ - TIMSK1 = 0; - TCCR1B = 0; - - /* Relocate the interrupt vector table back to the application section */ - MCUCR = (1 << IVCE); - MCUCR = 0; -} - -/** ISR to periodically toggle the LEDs on the board to indicate that the bootloader is active. */ -ISR(TIMER1_OVF_vect, ISR_BLOCK) -{ - LEDs_ToggleLEDs(LEDS_LED1 | LEDS_LED2); -} - -/** Event handler for the USB_ControlRequest event. This is used to catch and process control requests sent to - * the device from the USB host before passing along unhandled control requests to the library for processing - * internally. - */ -void EVENT_USB_Device_ControlRequest(void) -{ - /* Ignore any requests that aren't directed to the DFU interface */ - if ((USB_ControlRequest.bmRequestType & (CONTROL_REQTYPE_TYPE | CONTROL_REQTYPE_RECIPIENT)) != - (REQTYPE_CLASS | REQREC_INTERFACE)) - { - return; - } - - /* Activity - toggle indicator LEDs */ - LEDs_ToggleLEDs(LEDS_LED1 | LEDS_LED2); - - /* Get the size of the command and data from the wLength value */ - SentCommand.DataSize = USB_ControlRequest.wLength; - - switch (USB_ControlRequest.bRequest) - { - case DFU_REQ_DNLOAD: - Endpoint_ClearSETUP(); - - /* Check if bootloader is waiting to terminate */ - if (WaitForExit) - { - /* Bootloader is terminating - process last received command */ - ProcessBootloaderCommand(); - - /* Indicate that the last command has now been processed - free to exit bootloader */ - WaitForExit = false; - } - - /* If the request has a data stage, load it into the command struct */ - if (SentCommand.DataSize) - { - while (!(Endpoint_IsOUTReceived())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - - /* First byte of the data stage is the DNLOAD request's command */ - SentCommand.Command = Endpoint_Read_8(); - - /* One byte of the data stage is the command, so subtract it from the total data bytes */ - SentCommand.DataSize--; - - /* Load in the rest of the data stage as command parameters */ - for (uint8_t DataByte = 0; (DataByte < sizeof(SentCommand.Data)) && - Endpoint_BytesInEndpoint(); DataByte++) - { - SentCommand.Data[DataByte] = Endpoint_Read_8(); - SentCommand.DataSize--; - } - - /* Process the command */ - ProcessBootloaderCommand(); - } - - /* Check if currently downloading firmware */ - if (DFU_State == dfuDNLOAD_IDLE) - { - if (!(SentCommand.DataSize)) - { - DFU_State = dfuIDLE; - } - else - { - /* Throw away the filler bytes before the start of the firmware */ - DiscardFillerBytes(DFU_FILLER_BYTES_SIZE); - - /* Throw away the packet alignment filler bytes before the start of the firmware */ - DiscardFillerBytes(StartAddr % FIXED_CONTROL_ENDPOINT_SIZE); - - /* Calculate the number of bytes remaining to be written */ - uint16_t BytesRemaining = ((EndAddr - StartAddr) + 1); - - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Write flash - { - /* Calculate the number of words to be written from the number of bytes to be written */ - uint16_t WordsRemaining = (BytesRemaining >> 1); - - union - { - uint16_t Words[2]; - uint32_t Long; - } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}}; - - uint32_t CurrFlashPageStartAddress = CurrFlashAddress.Long; - uint8_t WordsInFlashPage = 0; - - while (WordsRemaining--) - { - /* Check if endpoint is empty - if so clear it and wait until ready for next packet */ - if (!(Endpoint_BytesInEndpoint())) - { - Endpoint_ClearOUT(); - - while (!(Endpoint_IsOUTReceived())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - } - - /* Write the next word into the current flash page */ - boot_page_fill(CurrFlashAddress.Long, Endpoint_Read_16_LE()); - - /* Adjust counters */ - WordsInFlashPage += 1; - CurrFlashAddress.Long += 2; - - /* See if an entire page has been written to the flash page buffer */ - if ((WordsInFlashPage == (SPM_PAGESIZE >> 1)) || !(WordsRemaining)) - { - /* Commit the flash page to memory */ - boot_page_write(CurrFlashPageStartAddress); - boot_spm_busy_wait(); - - /* Check if programming incomplete */ - if (WordsRemaining) - { - CurrFlashPageStartAddress = CurrFlashAddress.Long; - WordsInFlashPage = 0; - - /* Erase next page's temp buffer */ - boot_page_erase(CurrFlashAddress.Long); - boot_spm_busy_wait(); - } - } - } - - /* Once programming complete, start address equals the end address */ - StartAddr = EndAddr; - - /* Re-enable the RWW section of flash */ - boot_rww_enable(); - } - else // Write EEPROM - { - while (BytesRemaining--) - { - /* Check if endpoint is empty - if so clear it and wait until ready for next packet */ - if (!(Endpoint_BytesInEndpoint())) - { - Endpoint_ClearOUT(); - - while (!(Endpoint_IsOUTReceived())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - } - - /* Read the byte from the USB interface and write to to the EEPROM */ - eeprom_update_byte((uint8_t*)StartAddr, Endpoint_Read_8()); - - /* Adjust counters */ - StartAddr++; - } - } - - /* Throw away the currently unused DFU file suffix */ - DiscardFillerBytes(DFU_FILE_SUFFIX_SIZE); - } - } - - Endpoint_ClearOUT(); - - Endpoint_ClearStatusStage(); - - break; - case DFU_REQ_UPLOAD: - Endpoint_ClearSETUP(); - - while (!(Endpoint_IsINReady())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - - if (DFU_State != dfuUPLOAD_IDLE) - { - if ((DFU_State == dfuERROR) && IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Blank Check - { - /* Blank checking is performed in the DFU_DNLOAD request - if we get here we've told the host - that the memory isn't blank, and the host is requesting the first non-blank address */ - Endpoint_Write_16_LE(StartAddr); - } - else - { - /* Idle state upload - send response to last issued command */ - Endpoint_Write_8(ResponseByte); - } - } - else - { - /* Determine the number of bytes remaining in the current block */ - uint16_t BytesRemaining = ((EndAddr - StartAddr) + 1); - - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Read FLASH - { - /* Calculate the number of words to be written from the number of bytes to be written */ - uint16_t WordsRemaining = (BytesRemaining >> 1); - - union - { - uint16_t Words[2]; - uint32_t Long; - } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}}; - - while (WordsRemaining--) - { - /* Check if endpoint is full - if so clear it and wait until ready for next packet */ - if (Endpoint_BytesInEndpoint() == FIXED_CONTROL_ENDPOINT_SIZE) - { - Endpoint_ClearIN(); - - while (!(Endpoint_IsINReady())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - } - - /* Read the flash word and send it via USB to the host */ - #if (FLASHEND > 0xFFFF) - Endpoint_Write_16_LE(pgm_read_word_far(CurrFlashAddress.Long)); - #else - Endpoint_Write_16_LE(pgm_read_word(CurrFlashAddress.Long)); - #endif - - /* Adjust counters */ - CurrFlashAddress.Long += 2; - } - - /* Once reading is complete, start address equals the end address */ - StartAddr = EndAddr; - } - else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x02)) // Read EEPROM - { - while (BytesRemaining--) - { - /* Check if endpoint is full - if so clear it and wait until ready for next packet */ - if (Endpoint_BytesInEndpoint() == FIXED_CONTROL_ENDPOINT_SIZE) - { - Endpoint_ClearIN(); - - while (!(Endpoint_IsINReady())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - } - - /* Read the EEPROM byte and send it via USB to the host */ - Endpoint_Write_8(eeprom_read_byte((uint8_t*)StartAddr)); - - /* Adjust counters */ - StartAddr++; - } - } - - /* Return to idle state */ - DFU_State = dfuIDLE; - } - - Endpoint_ClearIN(); - - Endpoint_ClearStatusStage(); - break; - case DFU_REQ_GETSTATUS: - Endpoint_ClearSETUP(); - - while (!(Endpoint_IsINReady())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - - /* Write 8-bit status value */ - Endpoint_Write_8(DFU_Status); - - /* Write 24-bit poll timeout value */ - Endpoint_Write_8(0); - Endpoint_Write_16_LE(0); - - /* Write 8-bit state value */ - Endpoint_Write_8(DFU_State); - - /* Write 8-bit state string ID number */ - Endpoint_Write_8(0); - - Endpoint_ClearIN(); - - Endpoint_ClearStatusStage(); - break; - case DFU_REQ_CLRSTATUS: - Endpoint_ClearSETUP(); - - /* Reset the status value variable to the default OK status */ - DFU_Status = OK; - - Endpoint_ClearStatusStage(); - break; - case DFU_REQ_GETSTATE: - Endpoint_ClearSETUP(); - - while (!(Endpoint_IsINReady())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - - /* Write the current device state to the endpoint */ - Endpoint_Write_8(DFU_State); - - Endpoint_ClearIN(); - - Endpoint_ClearStatusStage(); - break; - case DFU_REQ_ABORT: - Endpoint_ClearSETUP(); - - /* Reset the current state variable to the default idle state */ - DFU_State = dfuIDLE; - - Endpoint_ClearStatusStage(); - break; - } -} - -/** Routine to discard the specified number of bytes from the control endpoint stream. This is used to - * discard unused bytes in the stream from the host, including the memory program block suffix. - * - * \param[in] NumberOfBytes Number of bytes to discard from the host from the control endpoint - */ -static void DiscardFillerBytes(uint8_t NumberOfBytes) -{ - while (NumberOfBytes--) - { - if (!(Endpoint_BytesInEndpoint())) - { - Endpoint_ClearOUT(); - - /* Wait until next data packet received */ - while (!(Endpoint_IsOUTReceived())) - { - if (USB_DeviceState == DEVICE_STATE_Unattached) - return; - } - } - else - { - Endpoint_Discard_8(); - } - } -} - -/** Routine to process an issued command from the host, via a DFU_DNLOAD request wrapper. This routine ensures - * that the command is allowed based on the current secure mode flag value, and passes the command off to the - * appropriate handler function. - */ -static void ProcessBootloaderCommand(void) -{ - /* Check if device is in secure mode */ - if (IsSecure) - { - /* Don't process command unless it is a READ or chip erase command */ - if (!(((SentCommand.Command == COMMAND_WRITE) && - IS_TWOBYTE_COMMAND(SentCommand.Data, 0x00, 0xFF)) || - (SentCommand.Command == COMMAND_READ))) - { - /* Set the state and status variables to indicate the error */ - DFU_State = dfuERROR; - DFU_Status = errWRITE; - - /* Stall command */ - Endpoint_StallTransaction(); - - /* Don't process the command */ - return; - } - } - - /* Dispatch the required command processing routine based on the command type */ - switch (SentCommand.Command) - { - case COMMAND_PROG_START: - ProcessMemProgCommand(); - break; - case COMMAND_DISP_DATA: - ProcessMemReadCommand(); - break; - case COMMAND_WRITE: - ProcessWriteCommand(); - break; - case COMMAND_READ: - ProcessReadCommand(); - break; - case COMMAND_CHANGE_BASE_ADDR: - if (IS_TWOBYTE_COMMAND(SentCommand.Data, 0x03, 0x00)) // Set 64KB flash page command - Flash64KBPage = SentCommand.Data[2]; - - break; - } -} - -/** Routine to concatenate the given pair of 16-bit memory start and end addresses from the host, and store them - * in the StartAddr and EndAddr global variables. - */ -static void LoadStartEndAddresses(void) -{ - union - { - uint8_t Bytes[2]; - uint16_t Word; - } Address[2] = {{.Bytes = {SentCommand.Data[2], SentCommand.Data[1]}}, - {.Bytes = {SentCommand.Data[4], SentCommand.Data[3]}}}; - - /* Load in the start and ending read addresses from the sent data packet */ - StartAddr = Address[0].Word; - EndAddr = Address[1].Word; -} - -/** Handler for a Memory Program command issued by the host. This routine handles the preparations needed - * to write subsequent data from the host into the specified memory. - */ -static void ProcessMemProgCommand(void) -{ - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00) || // Write FLASH command - IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Write EEPROM command - { - /* Load in the start and ending read addresses */ - LoadStartEndAddresses(); - - /* If FLASH is being written to, we need to pre-erase the first page to write to */ - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) - { - union - { - uint16_t Words[2]; - uint32_t Long; - } CurrFlashAddress = {.Words = {StartAddr, Flash64KBPage}}; - - /* Erase the current page's temp buffer */ - boot_page_erase(CurrFlashAddress.Long); - boot_spm_busy_wait(); - } - - /* Set the state so that the next DNLOAD requests reads in the firmware */ - DFU_State = dfuDNLOAD_IDLE; - } -} - -/** Handler for a Memory Read command issued by the host. This routine handles the preparations needed - * to read subsequent data from the specified memory out to the host, as well as implementing the memory - * blank check command. - */ -static void ProcessMemReadCommand(void) -{ - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00) || // Read FLASH command - IS_ONEBYTE_COMMAND(SentCommand.Data, 0x02)) // Read EEPROM command - { - /* Load in the start and ending read addresses */ - LoadStartEndAddresses(); - - /* Set the state so that the next UPLOAD requests read out the firmware */ - DFU_State = dfuUPLOAD_IDLE; - } - else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Blank check FLASH command - { - uint32_t CurrFlashAddress = 0; - - while (CurrFlashAddress < (uint32_t)BOOT_START_ADDR) - { - /* Check if the current byte is not blank */ - #if (FLASHEND > 0xFFFF) - if (pgm_read_byte_far(CurrFlashAddress) != 0xFF) - #else - if (pgm_read_byte(CurrFlashAddress) != 0xFF) - #endif - { - /* Save the location of the first non-blank byte for response back to the host */ - Flash64KBPage = (CurrFlashAddress >> 16); - StartAddr = CurrFlashAddress; - - /* Set state and status variables to the appropriate error values */ - DFU_State = dfuERROR; - DFU_Status = errCHECK_ERASED; - - break; - } - - CurrFlashAddress++; - } - } -} - -/** Handler for a Data Write command issued by the host. This routine handles non-programming commands such as - * bootloader exit (both via software jumps and hardware watchdog resets) and flash memory erasure. - */ -static void ProcessWriteCommand(void) -{ - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x03)) // Start application - { - /* Indicate that the bootloader is terminating */ - WaitForExit = true; - - /* Check if data supplied for the Start Program command - no data executes the program */ - if (SentCommand.DataSize) - { - if (SentCommand.Data[1] == 0x01) // Start via jump - { - union - { - uint8_t Bytes[2]; - AppPtr_t FuncPtr; - } Address = {.Bytes = {SentCommand.Data[4], SentCommand.Data[3]}}; - - /* Load in the jump address into the application start address pointer */ - AppStartPtr = Address.FuncPtr; - } - } - else - { - if (SentCommand.Data[1] == 0x00) // Start via watchdog - { - /* Unlock the forced application start mode of the bootloader if it is restarted */ - MagicBootKey = MAGIC_BOOT_KEY; - - /* Start the watchdog to reset the AVR once the communications are finalized */ - wdt_enable(WDTO_250MS); - } - else // Start via jump - { - /* Set the flag to terminate the bootloader at next opportunity */ - RunBootloader = false; - } - } - } - else if (IS_TWOBYTE_COMMAND(SentCommand.Data, 0x00, 0xFF)) // Erase flash - { - uint32_t CurrFlashAddress = 0; - - /* Clear the application section of flash */ - while (CurrFlashAddress < (uint32_t)BOOT_START_ADDR) - { - boot_page_erase(CurrFlashAddress); - boot_spm_busy_wait(); - boot_page_write(CurrFlashAddress); - boot_spm_busy_wait(); - - CurrFlashAddress += SPM_PAGESIZE; - } - - /* Re-enable the RWW section of flash as writing to the flash locks it out */ - boot_rww_enable(); - - /* Memory has been erased, reset the security bit so that programming/reading is allowed */ - IsSecure = false; - } -} - -/** Handler for a Data Read command issued by the host. This routine handles bootloader information retrieval - * commands such as device signature and bootloader version retrieval. - */ -static void ProcessReadCommand(void) -{ - const uint8_t BootloaderInfo[3] = {BOOTLOADER_VERSION, BOOTLOADER_ID_BYTE1, BOOTLOADER_ID_BYTE2}; - const uint8_t SignatureInfo[4] = {0x58, AVR_SIGNATURE_1, AVR_SIGNATURE_2, AVR_SIGNATURE_3}; - - uint8_t DataIndexToRead = SentCommand.Data[1]; - - if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x00)) // Read bootloader info - { - ResponseByte = BootloaderInfo[DataIndexToRead]; - } - else if (IS_ONEBYTE_COMMAND(SentCommand.Data, 0x01)) // Read signature byte - { - if (DataIndexToRead < 0x60) - ResponseByte = SignatureInfo[DataIndexToRead - 0x30]; - else - ResponseByte = SignatureInfo[DataIndexToRead - 0x60 + 3]; - } -} - |