From f68c5bf0d30dc1300c71dabc63d2c2970f7337c9 Mon Sep 17 00:00:00 2001
From: tmk <nobody@nowhere>
Date: Fri, 22 Feb 2013 09:53:46 +0900
Subject: Add initial files for PC98

---
 converter/pc98_usb/README | 79 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 79 insertions(+)
 create mode 100644 converter/pc98_usb/README

(limited to 'converter/pc98_usb/README')

diff --git a/converter/pc98_usb/README b/converter/pc98_usb/README
new file mode 100644
index 000000000..7b4f95ca2
--- /dev/null
+++ b/converter/pc98_usb/README
@@ -0,0 +1,79 @@
+Sun to USB keyboard protocol converter
+======================================
+Target MCU is ATMega32u4 but other USB capable AVR will also work.
+Supported keyboards: Sun Type 5 Keyboard, CTCSP SHORT TYPE KEYBOARD(CKUB)
+
+CTCSP SHORT TYPE KEYBOARD: http://imgur.com/a/QIv6p
+
+
+
+
+Connector
+---------
+  8Pin mini DIN
+     ___ ___
+    /  |_|  \
+   / 8  7  6 \
+  | 5    4  3 |
+   \_ 2   1 _/
+     \_____/  
+   (receptacle)
+
+    Wiring:
+    Pin mini DIN        MCU
+    ----------------------------------
+    1   GND             GND
+    2   GND             GND
+    3   5V
+    4   RX/TX(Mouse)
+    5   RX              PD3
+    6   TX              PD2
+    7   GND             GND
+    8   5V              VCC
+
+
+Protocol
+--------
+Singnal: Asynchronous, Negative logic, 1200baud, No Flow control
+Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit
+
+    AVR USART engine expects positive logic while Sun keyboard signal is negative.
+    To use AVR UART engine you need exteral inverter in front of RX and TX pin.
+    Otherwise you can software serial routine to communicate the keyboard.
+
+This converter uses software method, you doesn't need any inverter part.
+
+
+Commands From System To Keyboard
+    0x01 Reset
+            Keyboard responds with following byte sequence:
+            Success: 0xFF 0x04 0x7F
+            Fail:    0x7E 0x01 0x7F
+    0x02 Bell On
+    0x03 Bell Off
+    0x0A Click On
+    0x0B Click Off
+    0x0E LED
+            followed by LED status byte:
+            bit: 3       2       1       0
+            LED: CapsLk  ScrLk   Compose NumLk
+    0x0F Layout
+            Keyboard responds with 'Layout Response' 0xFE 0xXX
+
+Commands From Keyboard To System
+    0x7F Idle
+            means no keys pressed.
+    0xFE Layout Response
+    0xFF Reset Response(followed by 0x04)
+     
+Reference
+    http://kentie.net/article/sunkbd/page2.htm
+    http://kentie.net/article/sunkbd/KBD.pdf
+
+
+Build Firmware
+--------------
+Just use 'make'
+    $ cd sun_usb
+    $ make
+Then, load the binary to MCU with your favorite programmer.
-- 
cgit v1.2.3-24-g4f1b