From d678724ca8978b4d0ad981d11be4171e6315caca Mon Sep 17 00:00:00 2001 From: Drashna Jaelre Date: Fri, 4 May 2018 11:06:04 -0700 Subject: Fix Atom47 Keyboard --- keyboards/atom47/rev2/atom47.c | 31 ----------- keyboards/atom47/rev2/atom47.h | 25 --------- keyboards/atom47/rev2/config.h | 6 +- keyboards/atom47/rev2/keymaps/LEdiodes/atom47.c | 31 ----------- keyboards/atom47/rev2/keymaps/LEdiodes/atom47.h | 25 --------- keyboards/atom47/rev2/keymaps/LEdiodes/config.h | 74 ------------------------- keyboards/atom47/rev2/keymaps/LEdiodes/keymap.c | 35 ------------ keyboards/atom47/rev2/keymaps/LEdiodes/rules.mk | 65 ---------------------- keyboards/atom47/rev2/keymaps/default/keymap.c | 39 ------------- keyboards/atom47/rev2/keymaps/default/readme.md | 1 - keyboards/atom47/rev2/rev2.c | 31 +++++++++++ keyboards/atom47/rev2/rev2.h | 25 +++++++++ keyboards/atom47/rev2/rules.mk | 62 --------------------- 13 files changed, 59 insertions(+), 391 deletions(-) delete mode 100644 keyboards/atom47/rev2/atom47.c delete mode 100644 keyboards/atom47/rev2/atom47.h delete mode 100644 keyboards/atom47/rev2/keymaps/LEdiodes/atom47.c delete mode 100644 keyboards/atom47/rev2/keymaps/LEdiodes/atom47.h delete mode 100644 keyboards/atom47/rev2/keymaps/LEdiodes/config.h delete mode 100644 keyboards/atom47/rev2/keymaps/LEdiodes/keymap.c delete mode 100644 keyboards/atom47/rev2/keymaps/LEdiodes/rules.mk delete mode 100644 keyboards/atom47/rev2/keymaps/default/keymap.c delete mode 100644 keyboards/atom47/rev2/keymaps/default/readme.md create mode 100644 keyboards/atom47/rev2/rev2.c create mode 100644 keyboards/atom47/rev2/rev2.h (limited to 'keyboards/atom47/rev2') diff --git a/keyboards/atom47/rev2/atom47.c b/keyboards/atom47/rev2/atom47.c deleted file mode 100644 index 7b839e796..000000000 --- a/keyboards/atom47/rev2/atom47.c +++ /dev/null @@ -1,31 +0,0 @@ -#include "atom47.h" -#include "led.h" - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - matrix_init_user(); - led_init_ports(); -}; - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -}; - -void led_init_ports(void) { - // * Set our LED pins as output - DDRB &= ~(1<<5); -} - -void led_set_kb(uint8_t usb_led) { - if (usb_led & (1<. */ -#ifndef CONFIG_H -#define CONFIG_H +#ifndef REV2_CONFIG_H +#define REV2_CONFIG_H #include "config_common.h" @@ -26,7 +26,7 @@ along with this program. If not, see . #define DEVICE_VER 0x0003 #define MANUFACTURER Vortex #define PRODUCT Core -#define DESCRIPTION Atom47 PCB for the Vortex Core +#define DESCRIPTION Atom47 PCB for the Vortex Core Rev.2 /* key matrix size */ #define MATRIX_ROWS 4 diff --git a/keyboards/atom47/rev2/keymaps/LEdiodes/atom47.c b/keyboards/atom47/rev2/keymaps/LEdiodes/atom47.c deleted file mode 100644 index 7b839e796..000000000 --- a/keyboards/atom47/rev2/keymaps/LEdiodes/atom47.c +++ /dev/null @@ -1,31 +0,0 @@ -#include "atom47.h" -#include "led.h" - -void matrix_init_kb(void) { - // put your keyboard start-up code here - // runs once when the firmware starts up - matrix_init_user(); - led_init_ports(); -}; - -void matrix_scan_kb(void) { - // put your looping keyboard code here - // runs every cycle (a lot) - matrix_scan_user(); -}; - -void led_init_ports(void) { - // * Set our LED pins as output - DDRB &= ~(1<<5); -} - -void led_set_kb(uint8_t usb_led) { - if (usb_led & (1<. -*/ - -#ifndef CONFIG_H -#define CONFIG_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0003 -#define MANUFACTURER Vortex -#define PRODUCT Core -#define DESCRIPTION Atom47 PCB for the Vortex Core - -/* key matrix size */ -#define MATRIX_ROWS 4 -#define MATRIX_COLS 13 - -// ROWS: Top to bottom, COLS: Left to right - -#define MATRIX_ROW_PINS {B1,B2,B3,B7} -#define MATRIX_COL_PINS {D7,D5,F0,F1,F4,F6,F7,D4,C7,C6,D6,B5,B4} -#define UNUSED_PINS - -#define BACKLIGHT_PIN B6 - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* define if matrix has ghost */ -//#define MATRIX_HAS_GHOST - -/* Set 0 if debouncing isn't needed */ -#define DEBOUNCING_DELAY 5 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* key combination for command */ -#define IS_COMMAND() ( \ - keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ -) - -/* Backlight configuration - */ -#define BACKLIGHT_LEVELS 4 - -#define RGB_DI_PIN D0 // The pin the LED strip is connected to -#define RGBLED_NUM 1 // Number of LEDs in your strip - -#define QMK_ESC_OUTPUT D7 // usually COL -#define QMK_ESC_INPUT B1 // usually ROW -#define QMK_LED B6 - -#endif - diff --git a/keyboards/atom47/rev2/keymaps/LEdiodes/keymap.c b/keyboards/atom47/rev2/keymaps/LEdiodes/keymap.c deleted file mode 100644 index b987c433f..000000000 --- a/keyboards/atom47/rev2/keymaps/LEdiodes/keymap.c +++ /dev/null @@ -1,35 +0,0 @@ -#include QMK_KEYBOARD_H - -// These are all aliases for the function layers. -#define _L0 0 -#define _L1 1 -#define _L2 2 -#define _L3 3 - -#define _______ KC_TRNS - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { -[_L0] = LAYOUT_ansi( - KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \ - KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \ - KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_L1), \ - KC_LCTL, KC_LGUI, KC_LALT, TG(_L3), KC_SPC, KC_SPC, MO(_L2), KC_RALT, KC_APP, KC_RCTRL), \ - -[_L2] = LAYOUT_ansi( - _______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \ - KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \ - _______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ - -[_L1] = LAYOUT_ansi( - KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \ - KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \ - _______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ - -[_L3] = LAYOUT_ansi( - _______, _______, _______, KC_7, KC_8, KC_9, _______, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, KC_4, KC_5, KC_6, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, KC_1, KC_2, KC_3, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, _______, KC_0, KC_DOT, _______, _______, _______, RESET), \ -}; diff --git a/keyboards/atom47/rev2/keymaps/LEdiodes/rules.mk b/keyboards/atom47/rev2/keymaps/LEdiodes/rules.mk deleted file mode 100644 index d446d3a69..000000000 --- a/keyboards/atom47/rev2/keymaps/LEdiodes/rules.mk +++ /dev/null @@ -1,65 +0,0 @@ -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = no # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150) -MIDI_ENABLE = no # MIDI controls -AUDIO_ENABLE = no -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/atom47/rev2/keymaps/default/keymap.c b/keyboards/atom47/rev2/keymaps/default/keymap.c deleted file mode 100644 index 5f74416ce..000000000 --- a/keyboards/atom47/rev2/keymaps/default/keymap.c +++ /dev/null @@ -1,39 +0,0 @@ -#include QMK_KEYBOARD_H - -// Each layer gets a name for readability, which is then used in the keymap matrix below. -// The underscores don't mean anything - you can have a layer called STUFF or any other name. -// Layer names don't all need to be of the same length, obviously, and you can also skip them -// entirely and just use numbers. - -#define _MA 0 //Main layer -#define _FN 1 //Fn -#define _FN1 2 //Fn1 -#define _PN 3 //Pn - -#define _______ KC_TRNS - -const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { -[_MA] = LAYOUT_ansi( - KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \ - KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \ - KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_FN1), \ - KC_LCTL, KC_LGUI, KC_LALT, MO(_PN), KC_SPC, KC_SPC, MO(_FN), KC_RALT, KC_APP, KC_RCTRL), \ - -[_FN] = LAYOUT_ansi( - _______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \ - KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \ - _______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ - -[_FN1] = LAYOUT_ansi( - KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \ - KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \ - _______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ - -[_PN] = LAYOUT_ansi( - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET), -}; diff --git a/keyboards/atom47/rev2/keymaps/default/readme.md b/keyboards/atom47/rev2/keymaps/default/readme.md deleted file mode 100644 index ab86b4f12..000000000 --- a/keyboards/atom47/rev2/keymaps/default/readme.md +++ /dev/null @@ -1 +0,0 @@ -This is the default keymap as found on the Vortex Core, with some added buttons for backlight control. diff --git a/keyboards/atom47/rev2/rev2.c b/keyboards/atom47/rev2/rev2.c new file mode 100644 index 000000000..31a8561f0 --- /dev/null +++ b/keyboards/atom47/rev2/rev2.c @@ -0,0 +1,31 @@ +#include "rev2.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); +}; + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + matrix_scan_user(); +}; + +void led_init_ports(void) { + // * Set our LED pins as output + DDRB &= ~(1<<5); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<