From e337bb82a3b418dfd6c60b8c615322c854e5995d Mon Sep 17 00:00:00 2001
From: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
Date: Mon, 29 Apr 2019 11:04:56 -0700
Subject: Fix Planck and Preonic builds (#5658)

* Planck: Copy contents of Planck rules.mk to each revision

* Planck: Delete Planck rules.mk

* Planck: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Preonic: Copy contents of Preonic rules.mk to each revision

* Preonic: Delete Preonic rules.mk

* Preonic: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Planck: Delete non-specific Bootloader settings from revs. 1 and 2

Deleted BOOTLOADER setting code block, as the checks were only valid for revs. 3-5 and the Planck Light.

Neither Planck rev1 or rev2 set the bootloader via rules.mk, so there's no setting of BOOTLOADER in their rules.mk files.

* Preonic: Fix BOOTLOADER settings code blocks

* Preonic: delete extra blank lines from rules.mk files

* Preonic: delete AVR-type hardware config blocks from rev3

* Update Planck and Preonic readme files

- update Hardware Supported
- update/add Install Examples
- update Docs paragraph

* Enable Bootmagic Lite where it is disabled

Enabled Bootmagic Lite for:

- Planck Light
- Planck revs. 1-5
- Preonic revs. 1 and 2

* Remove `planck_grid` from LAYOUTS rule for all Planck revisions

Community has landed on `ortho_4x12`, which is already set; `planck_grid` is redundant.
---
 keyboards/preonic/rev2/rules.mk | 67 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)

(limited to 'keyboards/preonic/rev2/rules.mk')

diff --git a/keyboards/preonic/rev2/rules.mk b/keyboards/preonic/rev2/rules.mk
index e69de29bb..748979c79 100644
--- a/keyboards/preonic/rev2/rules.mk
+++ b/keyboards/preonic/rev2/rules.mk
@@ -0,0 +1,67 @@
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded 
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = qmk-dfu
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = lite     # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = yes         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = yes           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
+API_SYSEX_ENABLE = no
+
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+LAYOUTS = ortho_5x12
-- 
cgit v1.2.3-24-g4f1b