From 8a330b33ff41ffc1ec3f8fa39722e93115ea3f0f Mon Sep 17 00:00:00 2001 From: Legonut Date: Tue, 4 Dec 2018 21:15:52 -0500 Subject: Keyboard: Add new keyboard "Sol" from RGBKB (#4497) * Add final RGBKB Sol firmware * Apply suggestions from code review Apply most of the changes noroadsleft has suggested Co-Authored-By: Legonut * Cleanup readme * Cleanup keymaps per @noroadslefts suggestions * Remove eeproms, use set_single_persistent_default_layer * Suggestions from @noroadsleft and @drashna some small cleanup * Change RGB_SMOD to RGB_RMOD * fix RGB_SMOD * Apply suggestions from code review Remove redundant lines Co-Authored-By: Legonut --- keyboards/sol/rules.mk | 71 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 71 insertions(+) create mode 100644 keyboards/sol/rules.mk (limited to 'keyboards/sol/rules.mk') diff --git a/keyboards/sol/rules.mk b/keyboards/sol/rules.mk new file mode 100644 index 000000000..f53e5b21f --- /dev/null +++ b/keyboards/sol/rules.mk @@ -0,0 +1,71 @@ +SRC += i2c.c \ + serial.c \ + common/ssd1306.c + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Bootloader +# This definition is optional, and if your keyboard supports multiple bootloaders of +# different sizes, comment this out, and the correct address will be loaded +# automatically (+60). See bootloader.mk for all options. +BOOTLOADER = qmk-dfu + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = no # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +CUSTOM_MATRIX = yes + +DEFAULT_FOLDER = sol/rev1 -- cgit v1.2.3-24-g4f1b