From c5060ea81942b0e3f8577536ff78402a19abe3d3 Mon Sep 17 00:00:00 2001
From: tmk <nobody@nowhere>
Date: Sat, 25 Aug 2012 15:49:08 +0900
Subject: test build of 'Host shield' in minimal env.

---
 protocol/usb_hid/test/Makefile | 126 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 126 insertions(+)
 create mode 100644 protocol/usb_hid/test/Makefile

(limited to 'protocol/usb_hid/test/Makefile')

diff --git a/protocol/usb_hid/test/Makefile b/protocol/usb_hid/test/Makefile
new file mode 100644
index 000000000..39f5de455
--- /dev/null
+++ b/protocol/usb_hid/test/Makefile
@@ -0,0 +1,126 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
+# Target file name (without extension).
+TARGET = usb_hid_test
+
+TOP_DIR = ../../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# MCU name
+MCU = atmega32u4
+
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+
+# Build Options
+#   comment out to disable the options.
+#
+# Console for debug
+OPT_DEFS += -DCONSOLE_ENABLE
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#OPT_DEFS += -DBOOT_SIZE=4096
+
+
+
+SRC =  test.cpp
+SRC += common/debug.c
+SRC += common/print.c
+
+CONFIG_H = config.h
+
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+VPATH += $(TOP_DIR)/common
+
+
+
+# program Leonardo
+PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -P$(DEV) -b57600 -Uflash:w:$(TARGET).hex
+
+
+
+include $(TOP_DIR)/protocol/usb_hid.mk
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/rules.mk
-- 
cgit v1.2.3-24-g4f1b