summaryrefslogtreecommitdiffstats
path: root/converter/ps2_usb/Makefile
blob: 39455defdf5cb7d7930025134a0011edcf11930a (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
# 
# Makefile for Teensy
#
# Target file name (without extension).
TARGET = ps2_usb_lufa

# Directory common source filess exist
TMK_DIR = ../..

# Directory keyboard dependent files exist
TARGET_DIR = .

# project specific files
SRC =	keymap_common.c \
	matrix.c \
	led.c

ifdef KEYMAP
    SRC := keymap_$(KEYMAP).c $(SRC)
else
    SRC := keymap_plain.c $(SRC)
endif

CONFIG_H = config.h


# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=512


# Build Options
#   comment out to disable the options.
#
#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
CONSOLE_ENABLE = yes	# Console for debug(+400)
COMMAND_ENABLE = yes    # Commands for debug and configuration
NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA


# PS/2 Options
#
PS2_USE_USART = yes	# uses hardware USART engine for PS/2 signal receive(recomened)
#PS2_USE_INT = yes	# uses external interrupt for falling edge of PS/2 clock pin
#PS2_USE_BUSYWAIT = yes	# uses primitive reference code


# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax

# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TMK_DIR)

include $(TMK_DIR)/protocol.mk
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk