summaryrefslogtreecommitdiffstats
path: root/docs/feature_rgb_matrix.md
blob: f2168ab16ef44dda7c0293cea1fd72494bf632db (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
# RGB Matrix Lighting

This feature allows you to use RGB LED matrices driven by external drivers. It hooks into the RGBLIGHT system so you can use the same keycodes as RGBLIGHT to control it.

If you want to use single color LED's you should use the [LED Matrix Subsystem](feature_led_matrix.md) instead.

## Driver configuration
---
### IS31FL3731

There is basic support for addressable RGB matrix lighting with the I2C IS31FL3731 RGB controller. To enable it, add this to your `rules.mk`:

```C
RGB_MATRIX_ENABLE = IS31FL3731
```

Configure the hardware via your `config.h`:

```C
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 0b1110100 AD <-> GND
// 0b1110111 AD <-> VCC
// 0b1110101 AD <-> SCL
// 0b1110110 AD <-> SDA
#define DRIVER_ADDR_1 0b1110100
#define DRIVER_ADDR_2 0b1110110

#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 25
#define DRIVER_2_LED_TOTAL 24
#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL + DRIVER_2_LED_TOTAL
```

Currently only 2 drivers are supported, but it would be trivial to support all 4 combinations.

Define these arrays listing all the LEDs in your `<keyboard>.c`:

```C
const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
/* Refer to IS31 manual for these locations
    *   driver
    *   |  R location
    *   |  |      G location
    *   |  |      |      B location
    *   |  |      |      | */
    {0, C1_3,  C2_3,  C3_3},
    ....
}
```

Where `Cx_y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3731.pdf) and the header file `drivers/issi/is31fl3731.h`. The `driver` is the index of the driver you defined in your `config.h` (`0` or `1` right now).

---
###  IS31FL3733/IS31FL3737

!> For the IS31FL3737, replace all instances of `IS31FL3733` below with `IS31FL3737`.

There is basic support for addressable RGB matrix lighting with the I2C IS31FL3733 RGB controller. To enable it, add this to your `rules.mk`:

```C
RGB_MATRIX_ENABLE = IS31FL3733
```

Configure the hardware via your `config.h`:

```C
// This is a 7-bit address, that gets left-shifted and bit 0
// set to 0 for write, 1 for read (as per I2C protocol)
// The address will vary depending on your wiring:
// 00 <-> GND
// 01 <-> SCL
// 10 <-> SDA
// 11 <-> VCC
// ADDR1 represents A1:A0 of the 7-bit address.
// ADDR2 represents A3:A2 of the 7-bit address.
// The result is: 0b101(ADDR2)(ADDR1)
#define DRIVER_ADDR_1 0b1010000
#define DRIVER_ADDR_2 0b1010000 // this is here for compliancy reasons.

#define DRIVER_COUNT 2
#define DRIVER_1_LED_TOTAL 64
#define DRIVER_LED_TOTAL DRIVER_1_LED_TOTAL
```

Currently only a single drivers is supported, but it would be trivial to support all 4 combinations. For now define `DRIVER_ADDR_2` as `DRIVER_ADDR_1`

Define these arrays listing all the LEDs in your `<keyboard>.c`:

```C
const is31_led g_is31_leds[DRIVER_LED_TOTAL] = {
/* Refer to IS31 manual for these locations
    *   driver
    *   |  R location
    *   |  |       G location
    *   |  |       |       B location
    *   |  |       |       | */
    {0, B_1,    A_1,    C_1},
    ....
}
```

Where `X_Y` is the location of the LED in the matrix defined by [the datasheet](http://www.issi.com/WW/pdf/31FL3733.pdf) and the header file `drivers/issi/is31fl3733.h`. The `driver` is the index of the driver you defined in your `config.h` (Only `0` right now).

---

### WS2812 (AVR only)

There is basic support for addressable RGB matrix lighting with a WS2811/WS2812{a,b,c} addressable LED strand. To enable it, add this to your `rules.mk`:

```C
RGB_MATRIX_ENABLE = WS2812
```

Configure the hardware via your `config.h`:

```C
// The pin connected to the data pin of the LEDs
#define RGB_DI_PIN D7
// The number of LEDs connected
#define DRIVER_LED_TOTAL 70
```

---

From this point forward the configuration is the same for all the drivers. The struct rgb_led array tells the system for each led, what key electrical matrix it represents, what the physical position is on the board, and if the led is for a modifier key or not. Here is a brief example:

```C
const rgb_led g_rgb_leds[DRIVER_LED_TOTAL] = {
/*  {row | col << 4}
    *    |         {x=0..224, y=0..64}
    *    |            |              modifier
    *    |            |                | */
    {{0|(0<<4)},   {20.36*0, 21.33*0}, 1},
    {{0|(1<<4)},   {20.36*1, 21.33*0}, 1},
    ....
}
```

The first part, `{row | col << 4}`, tells the system what key this LED represents by using the key's electrical matrix row & col. The second part, `{x=0..224, y=0..64}` represents the LED's physical position on the keyboard. The `x` is between (inclusive) 0-224, and `y` is between (inclusive) 0-64 as the effects are based on this range. The easiest way to calculate these positions is imagine your keyboard is a grid, and the top left of the keyboard represents x, y coordinate 0, 0 and the bottom right of your keyboard represents 224, 64. Using this as a basis, you can use the following formula to calculate the physical position:

```C
x = 224 / (NUMBER_OF_COLS - 1) * COL_POSITION
y =  64 / (NUMBER_OF_ROWS - 1) * ROW_POSITION
```

Where NUMBER_OF_COLS, NUMBER_OF_ROWS, COL_POSITION, & ROW_POSITION are all based on the physical layout of your keyboard, not the electrical layout.

`modifier` is a boolean, whether or not a certain key is considered a modifier (used in some effects).

## Keycodes

All RGB keycodes are currently shared with the RGBLIGHT system:

* `RGB_TOG` - toggle
* `RGB_MOD` - cycle through modes
* `RGB_HUI` - increase hue
* `RGB_HUD` - decrease hue
* `RGB_SAI` - increase saturation
* `RGB_SAD` - decrease saturation
* `RGB_VAI` - increase value
* `RGB_VAD` - decrease value
* `RGB_SPI` - increase speed effect (no EEPROM support)
* `RGB_SPD` - decrease speed effect (no EEPROM support)
* `RGB_MODE_*` keycodes will generally work, but are not currently mapped to the correct effects for the RGB Matrix system

## RGB Matrix Effects

All effects have been configured to support current configuration values (Hue, Saturation, Value, & Speed) unless otherwise noted below. These are the effects that are currently available:

```C
enum rgb_matrix_effects {
    RGB_MATRIX_NONE = 0,
    RGB_MATRIX_SOLID_COLOR = 1,     // Static single hue, no speed support
    RGB_MATRIX_ALPHAS_MODS,         // Static dual hue, speed is hue for secondary hue
    RGB_MATRIX_GRADIENT_UP_DOWN,    // Static gradient top to bottom, speed controls how much gradient changes
    RGB_MATRIX_BREATHING,           // Single hue brightness cycling animation
    RGB_MATRIX_CYCLE_ALL,           // Full keyboard solid hue cycling through full gradient
    RGB_MATRIX_CYCLE_LEFT_RIGHT,    // Full gradient scrolling left to right 
    RGB_MATRIX_CYCLE_UP_DOWN,       // Full gradient scrolling top to bottom
    RGB_MATRIX_RAINBOW_MOVING_CHEVRON,  // Full gradent Chevron shapped scrolling left to right
    RGB_MATRIX_DUAL_BEACON,         // Full gradient spinning around center of keyboard
    RGB_MATRIX_RAINBOW_BEACON,      // Full tighter gradient spinning around center of keyboard
    RGB_MATRIX_RAINBOW_PINWHEELS,   // Full dual gradients spinning two halfs of keyboard
    RGB_MATRIX_RAINDROPS,           // Randomly changes a single key's hue
    RGB_MATRIX_JELLYBEAN_RAINDROPS, // Randomly changes a single key's hue and saturation
    RGB_MATRIX_DIGITAL_RAIN,        // That famous computer simulation
#if defined(RGB_MATRIX_KEYPRESSES) || defined(RGB_MATRIX_KEYRELEASES)
    RGB_MATRIX_SOLID_REACTIVE_SIMPLE,   // Pulses keys hit to hue & value then fades value out
    RGB_MATRIX_SOLID_REACTIVE,      // Static single hue, pulses keys hit to shifted hue then fades to current hue
    RGB_MATRIX_SOLID_REACTIVE_WIDE       // Hue & value pulse near a single key hit then fades value out
    RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE  // Hue & value pulse near multiple key hits then fades value out
    RGB_MATRIX_SOLID_REACTIVE_CROSS      // Hue & value pulse the same column and row of a single key hit then fades value out
    RGB_MATRIX_SOLID_REACTIVE_MULTICROSS // Hue & value pulse the same column and row of multiple key hits then fades value out
    RGB_MATRIX_SOLID_REACTIVE_NEXUS      // Hue & value pulse away on the same column and row of a single key hit then fades value out
    RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS // Hue & value pulse away on the same column and row of multiple key hits then fades value out
    RGB_MATRIX_SPLASH,              // Full gradient & value pulse away from a single key hit then fades value out
    RGB_MATRIX_MULTISPLASH,         // Full gradient & value pulse away from multiple key hits then fades value out
    RGB_MATRIX_SOLID_SPLASH,        // Hue & value pulse away from a single key hit then fades value out
    RGB_MATRIX_SOLID_MULTISPLASH,   // Hue & value pulse away from multiple key hits then fades value out
#endif
    RGB_MATRIX_EFFECT_MAX
};
```
    
You can disable a single effect by defining `DISABLE_[EFFECT_NAME]` in your `config.h`:


|Define                                                 |Description                                    |
|-------------------------------------------------------|-----------------------------------------------|
|`#define DISABLE_RGB_MATRIX_ALPHAS_MODS`               |Disables `RGB_MATRIX_ALPHAS_MODS`              |
|`#define DISABLE_RGB_MATRIX_GRADIENT_UP_DOWN`          |Disables `RGB_MATRIX_GRADIENT_UP_DOWN`         |
|`#define DISABLE_RGB_MATRIX_BREATHING`                 |Disables `RGB_MATRIX_BREATHING`                |
|`#define DISABLE_RGB_MATRIX_CYCLE_ALL`                 |Disables `RGB_MATRIX_CYCLE_ALL`                |
|`#define DISABLE_RGB_MATRIX_CYCLE_LEFT_RIGHT`          |Disables `RGB_MATRIX_CYCLE_LEFT_RIGHT`         |
|`#define DISABLE_RGB_MATRIX_CYCLE_UP_DOWN`             |Disables `RGB_MATRIX_CYCLE_UP_DOWN`            |
|`#define DISABLE_RGB_MATRIX_RAINBOW_MOVING_CHEVRON`    |Disables `RGB_MATRIX_RAINBOW_MOVING_CHEVRON`   |
|`#define DISABLE_RGB_MATRIX_DUAL_BEACON`               |Disables `RGB_MATRIX_DUAL_BEACON`              |
|`#define DISABLE_RGB_MATRIX_RAINBOW_BEACON`            |Disables `RGB_MATRIX_RAINBOW_BEACON`           |
|`#define DISABLE_RGB_MATRIX_RAINBOW_PINWHEELS`         |Disables `RGB_MATRIX_RAINBOW_PINWHEELS`        |
|`#define DISABLE_RGB_MATRIX_RAINDROPS`                 |Disables `RGB_MATRIX_RAINDROPS`                |
|`#define DISABLE_RGB_MATRIX_JELLYBEAN_RAINDROPS`       |Disables `RGB_MATRIX_JELLYBEAN_RAINDROPS`      |
|`#define DISABLE_RGB_MATRIX_DIGITAL_RAIN`              |Disables `RGB_MATRIX_DIGITAL_RAIN`             |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE`            |Disables `RGB_MATRIX_SOLID_REACTIVE`           |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_SIMPLE`     |Disables `RGB_MATRIX_SOLID_REACTIVE_SIMPLE`    |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_WIDE`       |Disables `RGB_MATRIX_SOLID_REACTIVE_WIDE`      |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE`  |Disables `RGB_MATRIX_SOLID_REACTIVE_MULTIWIDE` |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_CROSS`      |Disables `RGB_MATRIX_SOLID_REACTIVE_CROSS`     |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_MULTICROSS` |Disables `RGB_MATRIX_SOLID_REACTIVE_MULTICROSS`|
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_NEXUS`      |Disables `RGB_MATRIX_SOLID_REACTIVE_NEXUS`     |
|`#define DISABLE_RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS` |Disables `RGB_MATRIX_SOLID_REACTIVE_MULTINEXUS`|
|`#define DISABLE_RGB_MATRIX_SPLASH`                    |Disables `RGB_MATRIX_SPLASH`                   |
|`#define DISABLE_RGB_MATRIX_MULTISPLASH`               |Disables `RGB_MATRIX_MULTISPLASH`              |
|`#define DISABLE_RGB_MATRIX_SOLID_SPLASH`              |Disables `RGB_MATRIX_SOLID_SPLASH`             |
|`#define DISABLE_RGB_MATRIX_SOLID_MULTISPLASH`         |Disables `RGB_MATRIX_SOLID_MULTISPLASH`        |


## Custom layer effects

Custom layer effects can be done by defining this in your `<keyboard>.c`:

```C
void rgb_matrix_indicators_kb(void) {
    rgb_matrix_set_color(index, red, green, blue);
}
```

A similar function works in the keymap as `rgb_matrix_indicators_user`.


## Colors

These are shorthands to popular colors. The `RGB` ones can be passed to the `setrgb` functions, while the `HSV` ones to the `sethsv` functions.

|RGB                |HSV                |
|-------------------|-------------------|
|`RGB_WHITE`        |`HSV_WHITE`        |
|`RGB_RED`          |`HSV_RED`          |
|`RGB_CORAL`        |`HSV_CORAL`        |
|`RGB_ORANGE`       |`HSV_ORANGE`       |
|`RGB_GOLDENROD`    |`HSV_GOLDENROD`    |
|`RGB_GOLD`         |`HSV_GOLD`         |
|`RGB_YELLOW`       |`HSV_YELLOW`       |
|`RGB_CHARTREUSE`   |`HSV_CHARTREUSE`   |
|`RGB_GREEN`        |`HSV_GREEN`        |
|`RGB_SPRINGGREEN`  |`HSV_SPRINGGREEN`  |
|`RGB_TURQUOISE`    |`HSV_TURQUOISE`    |
|`RGB_TEAL`         |`HSV_TEAL`         |
|`RGB_CYAN`         |`HSV_CYAN`         |
|`RGB_AZURE`        |`HSV_AZURE`        |
|`RGB_BLUE`         |`HSV_BLUE`         |
|`RGB_PURPLE`       |`HSV_PURPLE`       |
|`RGB_MAGENTA`      |`HSV_MAGENTA`      |
|`RGB_PINK`         |`HSV_PINK`         |

These are defined in [`rgblight_list.h`](https://github.com/qmk/qmk_firmware/blob/master/quantum/rgblight_list.h). Feel free to add to this list!


## Additional `config.h` Options

```C
#define RGB_MATRIX_KEYPRESSES // reacts to keypresses
#define RGB_MATRIX_KEYRELEASES // reacts to keyreleases (instead of keypresses)
#define RGB_DISABLE_AFTER_TIMEOUT 0 // number of ticks to wait until disabling effects
#define RGB_DISABLE_WHEN_USB_SUSPENDED false // turn off effects when suspended
#define RGB_MATRIX_LED_PROCESS_LIMIT (DRIVER_LED_TOTAL + 4) / 5 // limits the number of LEDs to process in an animation per task run (increases keyboard responsiveness)
#define RGB_MATRIX_LED_FLUSH_LIMIT 16 // limits in milliseconds how frequently an animation will update the LEDs. 16 (16ms) is equivalent to limiting to 60fps (increases keyboard responsiveness)
#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 200 // limits maximum brightness of LEDs to 200 out of 255. If not defined maximum brightness is set to 255
```

## EEPROM storage

The EEPROM for it is currently shared with the RGBLIGHT system (it's generally assumed only one RGB would be used at a time), but could be configured to use its own 32bit address with:

```C
#define EECONFIG_RGB_MATRIX (uint32_t *)28
```

Where `28` is an unused index from `eeconfig.h`.

## Suspended state

To use the suspend feature, add this to your `<keyboard>.c`:

```C
void suspend_power_down_kb(void)
{
    rgb_matrix_set_suspend_state(true);
}

void suspend_wakeup_init_kb(void)
{
    rgb_matrix_set_suspend_state(false);
}
```