1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
|
Alternative Controller for HHKB
===============================
Feature
-------
- Mouse Keys
- NKRO on USB(PJRC Tennsy only)
- Keymap Layers
Customize Keymap
----------------
see keymap.c.
Build
=====
PJRC Teensy
-----------
0. Edit matrix.c.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
1. Define macros in config_pjrc.h.(Optional)
VENDOR_ID, PRODUCT_ID and string descriptor.
IS_COMMAND
2. Edit Makefile for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, NKRO_ENABLE
3. Build hex file.
$ make -f Makefile.pjrc
4. Program MCU.
$ make -f Makefile.pjrc program
V-USB
-----
0. Edit matrix.c and usbconfig.h.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
define macros for V-USB in usbconfig.h.
1. Define macros in config_vusb.h.(Optional)
IS_COMMAND
2. Edit Makefile.vusb for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
3. Build hex file.
$ make -f Makefile.vusb
4. Program MCU.
$ make -f Makefile.vusb program
Using a bootloader to program for convenience is recommended.
Once program this V-USB bootloader at first, you can program MCU without
extra programmer. You should have reset switch to start up as bootloader
mode in this case.
USBaspLoader:
http://www.obdev.at/products/vusb/usbasploader.html
iWRAP
-----
0. Edit matrix.c and usbconfig.h.
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
define macros for V-USB in usbconfig.h.
1. Define macros in config_iwrap.h.(Optional)
IS_COMMAND
2. Edit Makefile.iwrap for MCU setting and build options.
MCU, F_CPU
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
3. Build hex file.
$ make -f Makefile.iwrap
4. Program MCU.
$ make -f Makefile.iwrap program
Hardware
========
PJRC Teensy
-----------
+---------------+
| Teensy++ |
| |
| | HHKB
| | ~~~~
| PB0-2|------->ROW(6-8)
| PB3-5|------->COL(9-11)
| PB6|------->ENABLE(12)
| PE6|<-------KEY(4)
| PE7|------->PREV(5)
| |
| |
| |
+---------------+
V-USB
-----
+---+ +---------------+
USB GND | | ATmega168 |
~~~ C3 | |
5V <-------+--------+---|Vcc,AVCC | HHKB
R1 | | ~~~~
D- <----+--+-----R2-----|INT1 PB2-4|------->ROW(6-8)
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
Z1 Z2 | PC3|------->ENABLE(12)
GND<----+---+-----------|GND PB0|<-------KEY(4)
| PB1|------->PREV(5)
| |
GND+-C2--+--|XTAL1 RXD|------->Debug Console
X1 | TXD|<-------Debug Console
GND+-C3--+--|XTAL2 RST|---SW--+GND
+---------------+
R1: 1.5K Ohm
R2,R3: 68 Ohm
Z1,Z2: Zener 3.6V
C1,C2: 22pF
C3: 0.1uF
X1: Crystal 20MHz(16MHz/12MHz)
SW: Push Switch(Optional for bootloader)
iWRAP
-----
+---------------+ WT12
5V | ATmega168 | 5V/3.3V~~~~
+-----+---|Vcc,AVCC PC4|---/--->iWRAP(RxD)
USB | C3 | PC5|<--/----iWRAP(TxD)
~~~ | + | |
5V <--BATT + GND | | HHKB
R1 | | ~~~~
D- <----+-----+--R2-----|INT1 PB2-4|------->ROW(6-8)
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
Z1 Z2 | PC3|------->ENABLE(12)
GND<----+---+-----------|GND PB0|<-------KEY(4)
| PB1|------->PREV(5)
| |
GND+-C2--+--|XTAL1 RXD|------->Debug Console
X1 | TXD|<-------Debug Console
GND+-C3--+--|XTAL2 RST|---SW--+GND
+---------------+
R1: 1.5K Ohm
R2,R3: 68 Ohm
Z1,Z2: Zener 3.6V
C1,C2: 22pF
C3: 0.1uF
X1: Crystal 12MHz
SW: Push Switch(Optional)
BATT: Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V).
EOF
|