summaryrefslogtreecommitdiffstats
path: root/keyboard/atomic/Makefile
blob: 3f066aebcdfa385ab24d312f94817d3ffb8b63d4 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
#                Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
#               (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
#            have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
#             have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
#               (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
#                (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
#              with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
#                   bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------

# Target file name (without extension).
TARGET = atomic

# Directory common source filess exist
TOP_DIR = ../..
TMK_DIR = ../../tmk_core

# Directory keyboard dependent files exist
TARGET_DIR = .

# # project specific files
SRC = atomic.c

ifdef keymap
	KEYMAP = $(keymap)
endif

ifdef KEYMAP
ifneq ("$(wildcard keymaps/$(KEYMAP).c)","")
	KEYMAP_FILE = keymaps/$(KEYMAP).c
else
ifneq ("$(wildcard keymaps/$(KEYMAP)/keymap.c)","")
	KEYMAP_FILE = keymaps/$(KEYMAP)/keymap.c
ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
	include keymaps/$(KEYMAP)/makefile.mk
endif
else
$(error Keymap file does not exist)
endif 
endif

else

ifneq ("$(wildcard keymaps/default.c)","")
	KEYMAP_FILE = keymaps/default.c
else
	KEYMAP_FILE = keymaps/default/keymap.c
endif

ifneq ("$(wildcard keymaps/default/makefile.mk)","")
	include keymaps/default/makefile.mk
endif

endif

SRC := $(KEYMAP_FILE) $(SRC)

CONFIG_H = config.h

# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000

#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096

# Build Options
#   change to "no" to disable the options, or define them in the makefile.mk in 
#   the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE  = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE  = yes # Audio control and System control(+450)
CONSOLE_ENABLE   = yes # Console for debug(+400)
COMMAND_ENABLE   = yes # Commands for debug and configuration
NKRO_ENABLE      = no  # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
MIDI_ENABLE      = no  # MIDI controls
AUDIO_ENABLE     = no  # Audio output on port C6
UNICODE_ENABLE   = no  # Unicode
BLUETOOTH_ENABLE = no  # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE  = no  # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.

# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend

ifdef KEYMAP

ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
	include keymaps/$(KEYMAP)/makefile.mk
endif 
endif

else

ifneq ("$(wildcard keymaps/default/makefile.mk)","")
	include keymaps/default/makefile.mk
endif

endif

ifeq ($(strip $(BACKLIGHT_ENABLE)), yes)
	SRC := backlight.c $(SRC)
endif

# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax

# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
VPATH += $(TMK_DIR)

include $(TOP_DIR)/quantum/quantum.mk