1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
|
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = hhkb_lufa
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# List C source files here. (C dependencies are automatically generated.)
SRC += keymap_common.c \
matrix.c \
led.c
CONFIG_H = config.h
# MCU name
# PJRC Teensy++ 2.0
#MCU = at90usb1286
# TMK Alt Controller or PJRC Teensy 2.0
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096 (TMK Alt Controller)
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
MOUSEKEY_ENABLE = yes # Mouse keys
EXTRAKEY_ENABLE = yes # Audio control and System control
CONSOLE_ENABLE = yes # Console for debug
COMMAND_ENABLE = yes # Commands for debug and configuration
#NKRO_ENABLE = yes # USB Nkey Rollover
#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
#HHKB_JP = yes # HHKB JP support
ifdef HHKB_JP
OPT_DEFS += -DHHKB_JP
endif
#
# Keymap file
#
ifdef KEYMAP
SRC := keymap_$(KEYMAP).c $(SRC)
else
ifdef HHKB_JP
SRC := keymap_jp.c $(SRC)
else
SRC := keymap_hasu.c $(SRC)
endif
endif
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
include rn42.mk
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/protocol/lufa.mk
include $(TOP_DIR)/common.mk
include $(TOP_DIR)/rules.mk
debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
debug-on: all
debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
debug-off: all
|
