blob: 092eb4665debb811c4e28a2e37a35f435132b2fe (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
#include "satan.h"
#ifdef BACKLIGHT_ENABLE
#include "backlight.h"
#endif
__attribute__ ((weak))
void matrix_init_user(void) {
// leave these blank
};
__attribute__ ((weak))
void matrix_scan_user(void) {
// leave these blank
};
#ifdef BACKLIGHT_ENABLE
void backlight_init_ports()
{
// Setup PB6 as output and output low.
DDRB |= (1<<6);
PORTB &= ~(1<<6);
// Use full 16-bit resolution.
ICR1 = 0xFFFF;
// I could write a wall of text here to explain... but TL;DW
// Go read the ATmega32u4 datasheet.
// And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on
// Pin PB6 = OCR1B (Timer 1, Channel C)
// Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0
// (i.e. start high, go low when counter matches.)
// WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0
// Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1
TCCR1A = _BV(COM1B1) | _BV(WGM11); // = 0b00001010;
TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001;
backlight_init();
}
void backlight_set(uint8_t level)
{
// Prevent backlight blink on lowest level
PORTB &= ~(_BV(PORTB6));
if ( level == 0 )
{
// Turn off PWM control on PB6, revert to output low.
TCCR1A &= ~(_BV(COM1B1));
OCR1B = 0x0;
}
else if ( level == BACKLIGHT_LEVELS )
{
// Turn on PWM control of PB6
TCCR1A |= _BV(COM1B1);
// Set the brightness
OCR1B = 0xFFFF;
}
else
{
// Turn on PWM control of PB6
TCCR1A |= _BV(COM1B1);
// Set the brightness
OCR1B = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2));
}
}
#endif
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
if (matrix_init_user) {
(*matrix_init_user)();
}
led_init_ports();
#ifdef BACKLIGHT_ENABLE
backlight_init_ports();
#endif
};
void matrix_scan_kb(void) {
// put your looping keyboard code here
// runs every cycle (a lot)
if (matrix_scan_user) {
(*matrix_scan_user)();
}
};
|
